GRAUPNER mx-20 Hott Programming Manual page 248

Pha1  Nor mal
Pha2 – Landing
Pha3 – Strecke
Pha4 –
Pha5 –
Name
Then the timer is controlled through a corresponding
control switch to be defi ned on the C1 joystick. As soon
as you switch to the "Landing" fl ight phase, this fl ight
phase timer is automatically stopped and hidden in the
base screen. More about this can be found on page 142.
Now move the marking frame over the "Ph.Tim" column
to the "Motor" column to the right. Here you can decide
with "yes/no" in which phase the motor is controlled by
the throttle/brake joystick and the brake system to be
adjusted in the "Brake settings" submenu of the "Wing
mixers" menu should be shut off (= "yes") and vice
versa (= "no"):
Pha1 Normal

Pha2 – Landing
Strecke
Pha3 –
Pha4 –
Pha5 –
Name
Now move the marking frame once more to the right and
enter an appropriate switching time after activation of
the value fi eld of the "Sw.Time" column; for example:
248 Detail program description - Control adjust
Clk 1 Pha1
Pha2
Pha3
Pha4
Pha5
ph.Tim.
Then you must assigned these two fl ight phases to a
switch with which you can switch between the two fl ight
phases during the fl ight. In this case, a single switch is
suffi cient. It should be easy to reach, however, so that
you can still switch between "motor" and "brake" during
a landing approach, for example, without having to
release a joystick.
The assignment of the selected switch takes place in the
menu ...
"Phase assignment"
Select the switch symbol under "C" with one of the arrow
keys. After briefl y pressing the central
yes right touch pad, actuate the desired switch, such as
no
"SW 2".
PHASE ASSIGNMENT
prior
A B
motor
Both switch positions, in other words ON (I) and OFF ( )
are initially assigned in the bottom right of the display to
the phase "1 normal". With one of the arrow keys, select
this value fi eld and then, by briefl y pressing the central
SET key of the right touch pad, activate the selection list
of the phases which you set up in the "Phase setting"
 Normal 1.1s
– Landing 1.1s
– Strecke 0.1s
– 0.1s
0.1s
–
Name Sw.time
(page 134)
SET key of the
combi
C D E F
2
1 Normal
menu. For example, you name the phase for the front
switch position "normal" and "landing" for the rear
position (or vice versa):
PHASE ASSIGNMENT
prior combi
A B C D
2
2 Landing
These phase names then appear in all fl ight-phase
dependent menus and, of course, also in the base
screen of the transmitter.
Now switch to the "Landing" fl ight phase and in the
"Crow" line of the submenu ...
""Brake settings"
BRAKE SETTINGS
Crow 0% 0%
D.red 0% 0%
Elevat cur ve
Landing
AILE WK
... of the "Wing mixers" menu, set the desired throw of
the ailerons with actuation of the C1 joystick ("brake")
upward. Then, if applicable, switch to the "FL" column
in order to specify the desired through of the fl aps with
C1 actuation downward (hidden in the fi gure above).
This fl ap position is referred to as "Crow position" or
"Butterfl y; see also page 160.
In the line "D.red" (differentiation reduction), enter a
value which corresponds to the value you entered or
enter on the fi rst page of the "Wing mixers" menu in the
E F
(page 160)
0%
0%
WK2