Ricoh B156 Service Manual page 244

SERVICE PROGRAM MODE
2
(Class 1, 2, and 3)
980 Dctr Roller Interval
1 Job_Interruption: K
2 Job_Interruption: M
3 Job_Interruption: C
4 Job_Interruption: Y
5 Job_end: K
6 Job_end: M
7 Job_end: C
8 Job_end: Y
981 Toner Revitalization (3 and 4 requires BICU v1.04 and Main Unit Controller v1.05)
1 Job_Interruption
For A4 SEF, the
counter counts twice.
2 Job_ End
For A4 SEF, the
counter counts twice.
⇒
3 Toner Revitalization –
Duplex Job
Interruption
⇒
4 Toner Revitalization –
Duplex PCU Idling
⇒
5 Toner Revitalization –
Page Count Up
982 Dev. Motor Control
1 Speed Shift Time
2 Dev.CL_Off Time
⇒
983 Control Development Fan At Job End
1 Development Unit Fan
⇒
984 Duplex PCU Idling Setting (Requires BICU v1.04 and Main Unit Controller v1.05)
1 Total Period: T1
2 Printing Prohibited
Period: T2
B156/B220
CÓPIA NÃO CONTROLADA
Mode No.
Specifies the timing for reversing the doctor roller during
the multiple printing with single color. When this counter
reaches the prescribed value, reversing the doctor roller
is done during the print job.
In addition, reversing the doctor roller is done when the
counter reaches the 1/2 prescribed value in these SPs
after the toner near end has been detected.
[0 ~ 200 / 100 / 10 /step] 0: Disables job interruption.
Specifies the timing for reversing the doctor roller after
job end with single color. When this counter reaches the
prescribed value and next job is not commanded,
reversing the doctor roller is done after the job end.
[1 ~ 100 / 20 / 1 /step]
Specifies the number of prints for executing toner
revitalization in the middle of a job.
[0 ~ 200 / 100 / 10 /step]
0: Disables job interruption.
Specifies the number of prints for executing toner
revitalization at the end of a job.
[0 ~ 100 / 20 / 1 /step]
0: Disables toner refresh at end of a job.
The oil removal mode (PCU idling and toner refresh) is
carried out when the duplex printing accumulated
number. [0 ~ 200 / 30 / 1 sheet/step]
The duplex printing accumulated number is 6 (default) to
29 at the toner refresh mode timing after job end, the oil
removal mode is carried out. [0 ~ 200 / 6 / 1 sheet/step]
When the single printing is made, the number of the
single printing {absolute value of (default) times single
printing number} reduces the duplex printing
accumulated number. After oil removal mode the duplex
printing accumulated number is cleared to 0.
[0.0 ~ -1.0 / -0.1 / 0.1/step]
Specifies the interval for changing the development
motor speed from half speed to normal speed.
[0 ~ 500 / 100 / 10 ms/step] DFU
Specifies the interval until turning off the development
clutch after turning off the development motor.
[−150 ~ 0 / −60 / 10 ms/step] DFU
To prevent dirty background, which can occur in high-
temperature/high-humidity conditions turn ON the
development fan at job end. [0 ~ 900 / 0 / 10 s/step]
The total period of the PCU idling in duplex mode.
[6 ~ 200 / 60 / 1 s/step]
The machine can print 6 seconds (default) after PCU
idling starts.
[6 ~ 60 / 6 / 1 s/step]
CÓPIA NÃO CONTROLADA
Function / [ Setting ]
5-16
Rev. 10/2005
SM