Mazda CX-7 2007 Workshop Manual page 1268

SIDE AIR BAG MODULE REMOVAL/INSTALLATION
Warning
• Handling the air bag module improperly can accidentally operate (deploy) the air bag module,
which may seriously injure you. Read the air bag system service warnings and cautions before
handling the air bag module. (See 08-10-3 AIR BAG SYSTEM SERVICE WARNINGS.) (See 08-10-5
AIR BAG SYSTEM SERVICE CAUTIONS.)
• If the side air bag module is installed with debris in the seat back, the foreign material may be
scattered when the side air bag module operates (deploys), causing injury. Verify that there is no
foreign material in the seat back before installing the side air bag module.
1. Turn the ignition switch to the LOCK position.
2. Disconnect the negative battery cable and wait for 1 min or more.
3. Remove the front seat. (See 09-13-2 FRONT SEAT REMOVAL/INSTALLATION.)
4. Partially peel back the seat back trim.
5. Partially peel back the seat back pad.
6. Remove the seat cushion frame. (See 09-13-2 FRONT SEAT DISASSEMBLY/ASSEMBLY.)
7. Remove in the order indicated in the table.
1 Nut
2 Side air bag module
3 Connector
8. Install in the reverse order of removal.
9. Turn the ignition switch to the ON position.
10. Verify that the air bag system warning light
illuminates for approx. 6 s and goes out.
• If the air bag system warning light does not
operate normally, refer to the on-board
diagnostic system (air bag system) and
perform inspection of the system.
End Of Sie
CURTAIN AIR BAG MODULE REMOVAL/INSTALLATION WM: CURTAIN AIR BAG MODULE
Warning
• Handling the air bag module improperly can accidentally deploy the air bag module, which may
seriously injure you. Read the air bag system service warnings and cautions before handling the
air bag module. (See 08-10-3 AIR BAG SYSTEM SERVICE WARNINGS.) (See 08-10-5 AIR BAG
SYSTEM SERVICE CAUTIONS.)
1. Turn the ignition switch to the LOCK position.
2. Disconnect the negative battery cable and wait for 1 min or more.
3. Remove the following parts:
(1) A-pillar lower trim (See 09-17-16 A-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(2) A-pillar trim (See 09-17-15 A-PILLAR TRIM REMOVAL/INSTALLATION.)
(3) Front scuff plate inner (See 09-17-19 FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
(4) Rear scuff plate inner (See 09-17-19 REAR SCUFF PLATE REMOVAL/INSTALLATION.)
(5) B-pillar lower trim (See 09-17-16 B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
(6) Front seat belt upper anchor installation bolt (See 08-11-2 FRONT SEAT BELT REMOVAL/
INSTALLATION.)
(7) B-pillar upper trim (See 09-17-16 B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
(8) Rear seat (See 09-13-7 REAR SEAT REMOVAL/INSTALLATION.)
(9) Sub trunk box (See 09-17-25 SUB TRUNK BOX REMOVAL/INSTALLATION.)
(10)Trunk end trim (See 09-17-24 TRUNK END TRIM REMOVAL/INSTALLATION.)
(11)Trunk side trim (See 09-17-24 TRUNK SIDE TRIM REMOVAL/INSTALLATION.)
(12)C-pillar trim (See 09-17-17 C-PILLAR TRIM REMOVAL/INSTALLATION.)
(13)D-pillar trim (See 09-17-18 D-PILLAR TRIM REMOVAL/INSTALLATION.)
(14)Map light (See 09-18-22 MAP LIGHT REMOVAL/INSTALLATION.)
(15)Sunvisor (See 09-17-26 SUNVISOR REMOVAL/INSTALLATION.)
(16)Assist handle (See 09-17-27 ASSIST HANDLE REMOVAL/INSTALLATION.)
(17)Headliner (See 09-17-27 HEADLINER REMOVAL/INSTALLATION.)
(18)Rear speaker (See 09-20-8 REAR SPEAKER REMOVAL/INSTALLATION.)
08-10–8
AIR BAG SYSTEM
2
3
id081000800800
4.5—8.0
1
{46—81,
40—70}
N·m {kgf·cm, in·lbf}
acxuuw00000640
id081000800900