Extron electronics DMP 64 User Manual page 70

Command/Response table for DSP SIS commands (continued)
Command
Audio group master commands
NOTE: • See Group Masters, for more information about audio group masters.
• A group must have assigned members for these commands to have an effect.
X6^
• For , a positive (+) value is assumed unless a negative (-) value is specified.
X6^
• If entering a
with an "invalid parameter" (E13) error.
X6^ X6& X6*
• , , and
Set a group fader control
Example:
Raise a group fader control
Example
Lower a group fader control
View the group fader
control level
Mute a group mute control
Clear (unmute) a group
mute control
View a group mute control
Set soft limits
Example:
View soft limits
View group type
View group members
X6%
NOTE:
= Group master group number
X6^
= Group fader level
X6&
= Group fader increase/decrease
X6*
= Group fader soft limit
X6(
= Group type
ASCII command Response
(host to device) (device to host)
value outside the valid range for the group or outside the soft limits, the DMP 64 responds
values can be sent without leading zeroes; responses are always 5 digits.
E X6% X6^ }
D * GRPM Grpm
E }
GrpmD02*-
d2*-293*GRPM
00293*GRPM
E X6% X6& }
D * +GRPM Grpm
E }
GrpmD02*-
d2*30+GRPM
00263*GRPM
E X6% X6& }
D * -GRPM Grpm
E X6% }
D GRPM Grpm
E X6% }
D *1GRPM GrpmD
E X6% }
D *0GRPM GrpmD
E X6% }
D GRPM GrpmD
E X6% * X6* * X6* }
L GRPM
upper lower
GrpmL
E }
L2 +60 -60GRPM GrpmL02*+00060*-00060
* *
E X6% }
L GRPM GrpmL
E X6% }
P GRPM GrpmP
E X6% }
O GRPM GrpmO
...*
01 - 32.
dB value, in 0.1 dB increments, using negative numbers but not
decimal places. -100.0 dB to +80.0 dB is represented by -1000 to 800.
The valid range depends on the type of gain or trim block assigned
to the group number (
dB value, in 0.1 dB increments, to raise or lower a group fader.
dB value, in 0.1 dB increments. The valid range must be within the
range for the gain block grouped in
6= gain
12 = mute
Additional
description
X6% X6^]
Set the group fader to a value
*
X6^
of
Set the group 2 fader control
]
to -29.3 dB.
X6% X6^]
* Increase the level of the
group fader by
Raise the group 2 fader 3 dB
]
(from -29.3 dB to -26.3 dB,
starting from the level set
in the "Set a group fader
control" example, above.
X6% X6^]
* Decrease the level of the
group fader by
X6% X6^]
In verbose modes 1 and 2, the
*
response is simplified to
X6^]
X6% ]
*+00001 Mute all blocks in group
X6% ]
Umute all blocks in group
*+00000
X6%
.
X6% X6$]
* For group masters,
always expressed as a positive
or negative 5-digit value.
Set the groups soft limits to
X6*
and
X6% X6* X6*]
* *
]
Set the upper soft limit for the
group 2 fader to +6.0 dB and
the lower limit to -6.0 dB.
X6% X6* X6*]
In verbose modes 0 and 1,
* *
the response is simplified to
X6* X6*]
*
X6% X6(]
* Show the group type (
for group
modes 0 and 1, the response
is simplified to
X6% X6) X6) X6)
* 1 * 2 * is the control or mix point.
X6) ]
In verbose modes 0 and 1,
16
the response is simplified to
X6) X6)
1 *
X6%
).
X6%
.
DMP 64 • SIS Programming and Control
.
X6%
X6&
dB.
X6%
X6&
dB.
.
X6%
.
X6$
is
X6*
.
.
X6(
)
X6%
. In verbose
X6(]
.
X6) ]
2 *...* 16 .
64