D Command Table - Icom IC-7800 Instruction Manual

D D Command table
Command Sub command
00 —
01 Same as
command 06
02 —
03 —
04 —
05 —
06 00
01
02
03
04
05
07
08
12
13
07 —
B0
B1
C0
C1
D0
D1
08 —
0001–0101*
09 —
0A —
0B —
0E 00
01
02
03
12
13
22
23
A1–A7
B0
B1
B2
D0
D3
0F 00
01
10 00
01
02
03
04
05
06
07
08
Description
Send frequency data
Send mode data
Read band edge frequencies
Read operating frequency
Read operating mode
Set operating frequency
Select LSB
Select USB
Select AM
Select CW
Select RTTY
Select FM
Select CW-R
Select RTTY-R
Select PSK
Select PSK-R
Select VFO mode
Exchange main and sub bands
Equalize main and sub bands
Turn the dualwatch OFF
Turn the dualwatch ON
Select main band
Select sub band
Select memory mode
Select memory channel
*P1=0100, P2=0101
Memory write
Memory to VFO
Memory clear
Scan stop
Programmed/memory scan start
Programmed scan start
∂F scan start
Fine programmed scan start
Fine ∂F scan start
Memory scan start
Select memory scan start
Set ∂F scan span (A1=±5 kHz;
A2=±10 kHz; A3=±20 kHz;
A4=±50 kHz; A5=±100 kHz;
A6=±500 kHz; A7=±1 MHz)
Set as non-select channel
Set as select channel (1=#1;
2=#2; 3=#3; when no data com-
mand is specified, the previously
set number or "#1" is selected)
Set the number for select memory
scan (0=ALL; 1=#1; 2=#2; 3=#3)
Set scan resume OFF
Set scan resume ON
Turn the split function OFF
Turn the split function ON
Select 10 Hz (1 Hz) tuning step
Select 100 Hz tuning step
Select 1 kHz tuning step
Select 5 kHz tuning step
Select 9 kHz tuning step
Select 10 kHz tuning step
Select 12.5 kHz tuning step
Select 20 kHz tuning step
Select 25 kHz tuning step
Command Sub command
11 —
12 00 + RX ANT
01 + RX ANT
02 + RX ANT
03 + RX ANT
13 00
01
02
14 01 + Level data [AF] level setting (0=max. CCW to
02 + Level data [RF] level setting (0=max. CCW to
03 + Level data [SQL] level setting (0=11 o'clock to
05 + Level data [APF] level setting
06 + Level data [NR] level setting (0=min. to
07 + Level data Inside [TWIN PBT] setting or IF
08 + Level data Outside [TWIN PBT] setting
09 + Level data [CW PITCH] setting (0=300 Hz,
0A + Level data [RF POWER] setting (0=max.
0B + Level data [MIC] setting (0=max. CCW to
0C + Level data [KEY SPEED] setting (0=max.
0D + Level data [NOTCH] setting (0=low freq. to
0E + Level data [COMP] setting (0=max. CCW to
0F + Level data [DELAY] setting (0=max. CCW to
11 + Level data [AGC] control setting (0=max.
12 + Level data [NB] control setting (0=max. CCW
13 + Level data [DIGI-SEL] setting (0=max. CCW
14 + Level data [DRIVE] setting (0=max. CCW to
15 + Level data [MONI GAIN] setting (0=max.
16 + Level data [VOX GAIN] setting (0=max.
17 + Level data [ANTI VOX] setting (0=max. CCW
18 + Level data [CONTRAST] setting (0=max.
19 + Level data [BRIGHT] setting (0=max. CCW
14-3
CONTROL COMMAND
Description
Select/read attenuator (0=OFF;
1=3 dB; 2=6 dB; 3=9 dB; 4=12 dB;
5=15 dB; 6=18 dB; 7=21 dB)
Select/read ANT1 selection
(00=RX ANT OFF; 01=RX ANT ON)
Select/read ANT2 selection
(00=RX ANT OFF; 01=RX ANT ON)
Select/read ANT3 selection
(00=RX ANT OFF; 01=RX ANT ON)
Select/read ANT4 selection
(00=RX ANT OFF; 01=RX ANT ON)
Announce with voice synthesizer
(00=all data; 01=frequency and
S-meter level; 02=receive mode)
255=max. CW)
255=11 o'clock)
255=max. CW)
(0=Pitch–550 Hz, 128=Pitch,
255=Pitch+550 Hz; 10 Hz steps)
255=max.)
shift setting (0=max. CCW,
128=center, 255=max. CW)
(0=max. CCW, 128=center,
255=max. CW)
128=600 Hz, 255=900 Hz; 5 Hz
steps)
CCW to 255=max. CW)
255=max. CW)
CCW to 255=max. CW)
255=high freq.)
255=max. CW)
255=max. CW)
CCW to 255=max. CW)
to 255=max. CW)
to 255=max. CW)
255=max. CW)
CCW to 255=max. CW)
CCW to 255=max. CW)
to 255=max. CW)
CCW to 255=max. CW)
to 255=max. CW)
14