D Command Table - Icom ID-51A Advanced Instructions

Previous view
17
OTHER FUNCTIONS
CI-V information (Continued)
■

D Command table

Cmd. Sub Data
cmd.
00 see p. 17-24 Send operating frequency for transceive
01 see p. 17-24 Send operating mode for transceive
03 see p. 17-24 Read operating frequency
04 see p. 17-24 Read operating mode
05 see p. 17-24 Send operating frequency
06 see p. 17-24 Send operating mode
07 D0 Select A band
Dualwatch: Set the Main band as the A band
Single watch: Select the A band
D1 Select B band
Dualwatch: Set the Main band as the B band
Single watch: Select the B band
0C see p. 17-24 Read frequency offset*
0D see p. 17-24 Send frequency offset
0F Read duplex setting
(10=simplex, 11=DUP–, 12=DUP+)
10 Set simplex operation
11 Set DUP– operation
12 Set DUP+ operation
11 00 Send/read attenuator OFF (AIR band)
30 Send/read 30 dB attenuator (AIR band)
14 01 see p. 17-24 Send/read audio output level
03 see p. 17-24 Send/read squelch level
0A see p. 17-24 Send/read RF power setting
0B see p. 17-24 Send/read external microphone gain.
16 see p. 17-24 Send/read VOX gain.
15 01 00 Read noise/S-meter squelch status (squelch
close)
01 Read noise/S-meter squelch status (squelch
open)
02 0000 to
Read S-meter level (0000=S0, 0170=S9)
0255
05 00 Read tone squelch and RF squelch status
(squelch close)
01 Read tone squelch and RF squelch status
(squelch open)
11 Read RF power meter
0000 to
(0005=S-LOW, 0026=LOW1, 0051=LOW2,
0255
0128=MID, 0255=HIGH)
16 42 00 Send/read Repeater tone OFF
01 Send/read Repeater tone ON
43 00 Send/read Tone squelch OFF
Send/read Tone squelch ON
01
02 Send/read Reversed Tone squelch ON
46 00 Send/read VOX function OFF
01 Send/read VOX function ON
4B 00 Send/read DTCS OFF
01 Send/read DTCS ON
02 Send/read Reversed DTCS ON
59 00 Send/read Sub band OFF
01 Send/read Sub band ON
5B 00 Send/read DSQL/CSQL OFF (DV mode only)
01 Send/read DSQL ON (DV mode only)
02 Send/read CSQL ON (DV mode only)
18 00 Turning the transceiver power OFF
01 Turning the transceiver power ON*
19 00 Read transceiver ID.
Description
1
2
17-23
Cmd. Sub Data
cmd.
see p. 17-24 Send/read Repeater tone frequency
1B 00
see p. 17-24 Send/read Tone squelch frequency
01
see p. 17-24 Send/read DTCS code and polarity
02
07 see p. 17-25 Send/read CSQL code (DV mode)
1C 00 00 Send/read Transceiver's status (RX)
Send/read Transceiver's status (TX)
01
see p. 17-25 Send/read DV MY call sign
1F 00
01 see p. 17-25 Send/read DV TX call signs
02 see p. 17-25 Send/read DV TX message
20 00 00 00* 3 Send/read Auto DV RX Call signs output OFF
01* 3 Send/read Auto DV RX Call signs output ON
01 see p. 17-26 Output DV RX Call signs
02 see p. 17-26 Read DV RX Call signs
01 00 00* 3 Send/read Auto DV RX message output OFF
01* 3 Send/read Auto DV RX message output ON
see p. 17-26 Output DV RX message
01
see p. 17-26 Read DV RX message
02
00* 3 Send/read Auto DV RX status output OFF
02 00
3
01* Send/read Auto DV RX status output ON
01 see p. 17-25 Output DV RX status
02 see p. 17-25 Read DV RX status
* 1 : Less than 100 Hz is omitted.
* 2 : When sending the power ON command (18 01), the com-
mand "FE" must be sent before the basic format.
：50
• 19200bps
：26
• 9600bps
：14
• 4800bps
：5
• 1200bps
：3
• 300bps
e.g.: When operating with 4800 bps
q w
F E
F E F E 8
×14
q Preamble code (fixed)
w Transceiver's default address
e Controller's default address
r Command number
t Sub command number
u End of message code (fixed)
* 3 : Output setting is automatically turned OFF after turning
the power OFF, then ON.
Description
e r t
6 E O 1 8 0 1 F
u
D