Page 2
8. READ the instructions of test equipment throughly before connecting a test equipment to the transceiver. Icom, Icom Inc. and logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.
* 1 Pre-amp1 is ON * 2 Pre-amp2 is ON • Frequency stability : Less than ±0.05 ppm • Squelch sensitivity : (Pre-amp OFF) (IC-7800’s condition: After 5 min. since SSB/CW/RTTY/PSK31 Less than 5.6 µV turns power ON on the rear panel) Less than 1.0 µV...
Page 6
SECTION 2 INSIDE VIEWS UPPER LAYER PA200W board REG unit BPF unit FILTER unit ANT-SW unit CTRL board Rear panel TUNER unit Front panel LOGIC unit FRONT unit OSC unit DIGISEL unit DC-DC unit UNDER LAYER SCOPE unit MAIN unit RXPLL-B unit Rear panel Front panel...
TOP VIEW PA UNIT ANT-SW UNIT FILTER UNIT TUNER UNIT BPF UNIT DIGISEL UNIT OSC UNIT DC-DC UNIT LOGIC UNIT FRONT UNIT BOTTOM VIEW DSP-A BOARD DSP-A BOARD DSP-B BOARD DSP-B BOARD SCOPE UNIT SCOPE UNIT MAIN UNIT MAIN UNIT DSP-TX BOARD DSP-TX BOARD RXPLL-A UNIT...
MAIN UNIT AF power amplifier AF power amplifier (IC140: LA4485) (IC140: LA4485) SQL gate SQL gate (Q100,Q101: 2SJ144) (Q100,Q101: 2SJ144) (IC105,IC180: NJM2172V) (IC105,IC180: NJM2172V) AF selection circuit AF selection circuit (IC100,IC101: TC4W53F) (IC100,IC101: TC4W53F) ACC AF output circuit ACC AF output circuit Head phone amplifier Head phone amplifier (IC182: TPA6111A2DGN)
RF bandpass filters pass only the desired band signals and ( BPF, RXPLL-A, AND RXPLL-B UNITS) suppress any undesired band signals. The RF circuit has The IC-7800 has 2 gain levels of pre-amplifier circuits 11 bandpass filters and 1 low-pass filter. which is composed of the pre-amplifier1 and pre-amplifier2.
Page 14
(L1058, L1060, L1062, L1063, C1061, C1062, C1064, a 64.455 MHz (main) or 64.555 MHz (sub) 1st IF signal. C1066, C1070, C1074, R1054), and is then applied to the The IC-7800 has four 1st mixer circuits for the dualwatch 1st IF circuit. function.
Page 15
3-1-5 1ST IF CIRCUIT The 2nd IF signal from the other 2nd mixer circuit (IC1502, pin 5) is amplified at the buffer amplifier (Q1502), and is (RXPLL-A AND RXPLL-B UNITS) then applied to the 2nd IF amplifier (IC1504, pin 3). The The 1st IF circuit filters and amplifies the 1st IF signal.
Page 16
3-1-7 DSP RECEIVER CIRCUIT The converted analog AF signals pass through the low- pass filter (IC601, pins 3, 6, IC651, pins 3, 6), and are then (DSP-A AND DSP-B BOARDS) applied to the buffer amplifier (IC701, pins 2, 3) to convert The DSP (Digital Signal Processor) circuit enables digital into unbalancing signals.
3-1-9 AGC CIRCUIT line. The amplified signals are applied to the RXPLL-B unit via the J1701, pin 9 as “DAGC” line after being passed ( RXPLL-A AND RXPLL-B UNITS AND DSP-A AND through the J400, pin 8 on MAIN unit as “AGC1B” line. The DSP-B BOARDS) applied signals are amplified at the AGC amplifier (RXPLL_B The AGC (Automatic Gain Control) circuit reduces IF...
Page 18
The converted analog IF signal passes through the low- The filtered signal is applied to the YGR amplifier (Q801), pass filter (IC601, pins 3, 6, IC651, pins 3, 6), and is then and passes through the 3 dB attenuator (R805–R807). The applied to the IF amplifier (IC701, pins 2, 3) to convert to signal is applied to the power amplifier circuit via the J801.
(CTRL BOARD, LOGIC AND MAIN UNITS) The ALC (Automatic Level Control) circuit controls the gain of IF amplifiers in order for the IC-7800 to output a constant 3-2-13 TEMPERATURE PROTECTION CIRCUIT RF power set by [RF PWR] control even when the supplied (PA200W BOARD) voltage shifts, etc.
Page 20
• USING REFERENCE SIGNAL TO EXTERNAL The oscillated signal is amplified at the buffer amplifier The oscillated signal is amplified at the buffer amplifier (Q301), and passes through the high-pass (L331, C331– (Q21), and is then applied to the amplifier (Q42). The C333) and low-pass (D341, L332, C334–C337) filters.
Page 21
(2) RX 2ND LO CIRCUIT The amplified signal from Q151 is applied to the PLL IC’s The signal from the hybrid divider passes through the 1/21 divider section (IC201, pin 8), and is then applied to attenuator (R802, R803), and is then applied to the the PLL section.
Page 22
• DSP SYSTEM CLOCK CIRCUIT –C685) and high-pass (L683, C686–C688) filters to suppress unwanted signals. The filtered signal is The 40 MHz reference signal is applied to the amplifier amplified at the buffer amplifier (Q680), and passes (IC652) via the “40M” line, and is then applied to the through the attenuator (R690–R692).
• SCOPE UNIT SYSTEM CLOCK CIRCUIT 3-4-3 MOTOR CONTROL CIRCUIT The 40 MHz reference signal is amplified at the buffer (CTRL BOARD AND TUNER UNIT) amplifier (Q601) via the “40M” line, and then passes The control circuit of the internal antenna tuner consists of through the low-pass filter (L602, L603, C609–C613).
Page 24
3-5-3 SWEEP LO CIRCUIT (SCOPE UNIT) 3-5 SCOPE CIRCUITS The 40 MHz signal is applied to the J3 from the RXPLL-B 3-5-1 SCOPE RECEIVER CIRCUIT (SCOPE UNIT) unit. The signal is used for reference system clock of each A portion of the 64.455 MHz 1st IF signal from the 1st circuits.
(3) DDS LO CIRCUIT The 40 MHz reference system clock is amplified at the amplifiers (Q701, IC602, IC603), and is then applied to the DSP IC (IC601). The applied signal is quintupled in the IC, then uses 200 MHz DSP system clock signal. The 200 MHz clock signal is divided 1/400, and then uses as the 500 kHz sampling frequency of the A/D converter (IC501).
3-7 PORT ALLOCATIONS Port 3-7-1 MAIN CPU2 PORT ALLOCATIONS Description number name (LOGIC UNIT; IC604) DSPCK Outputs clock signal to the DSP IC. Port Description DSPR Outputs data signal to the DSP IC. number name Outputs start signal to the internal 5–9 H8_A0–A4 ISTA...
Page 27
Port Description number name Input port for the driving current FANI detect signal at the cooling fan. Input port for the external keypad on EPAD the rear panel. Input port for the data signal from the DX1A DSP IC on the DSP-A board. Input port for the data signal from the DX1B DSP IC on the DSP-B board.
Page 28
3-7-2 FRONT CPU (DISPLAY BOARD; IC6) Port Description number name Port Description number name Input port for [F-4]. CNTV Outputs LCD contrast control signal. Input port for [F-5]. Outputs LCD brightness control Input port for [F-6]. BRIV signal. Input port for [F-7]. Outputs data signal to the SERI LDAT SSBK...
Page 29
3-7-3 CPDL CPU (LOGIC UNIT; IC605) Port Port Description Description number name number name Outputs strobe signal to the band Outputs unlock signal to the DSP-A CSTB controller (CTRL board; IC51; pin 1). board. DULSA High : Unlock. Outputs strobe signals to the relay controllers (CTRL board;...
Page 30
3-7-4 MAIN CPU1 (LOGIC UNIT; IC103 ) Port Description number name Port Description number name 198, RESET, Input ports for the reset signal. TRST Input port for the mode signal. MRESET Input port for the manual reset signal. Input port for the clock signal. Outputs the buffer amplifier (IC106) Input port for the data signal.
Page 31
3-7-7 RELAY CONTROLLER (ANT-SW UNIT; IC11) 3-7-8 RELAY CONTROLLER (BPF UNIT; IC101) Port Port Description Description number name number name Outputs the antenna ([ANT 1]) select Outputs the RX-A circuit bandpass fil- ANT1A signal for main band. ter (0.03–1.6 MHz) select signal. Outputs the antenna ([ANT 1]) select Outputs the RX-A circuit bandpass fil- ANT1B...
Page 32
3-7-9 RELAY CONTROLLER (BPF UNIT; IC102) 3-7-10 RELAY CONTROLLER (BPF UNIT; IC401) Port Port Description Description number name number name Outputs the RX-A circuit bandpass Outputs the RX-B circuit bandpass fil- filter group select signal. ter (0.03–1.6 MHz) select signal. HF50A Low : While receiving on 30–60 MHz.
Page 33
3-7-11 RELAY CONTROLLER (BPF UNIT; IC402) 3-7-14 CONTROLLER IC (DIGISEL-B UNIT; IC504) Port Port Description Description number name number name Outputs the RX-B circuit bandpass X1B, Output the network serial reactance filter group select signal. control signals. HF50B Low : While receiving on 30–60 MHz. Output the network I/O capacitance 8–11 S1B–S4B...
Page 34
3-7-18 RELAY CONTROLLER (RXPLL-B UNIT; IC1701) 3-7-20 BUFFER IC (MAIN UNIT; IC291) Port Port Description Description number name number name Outputs the HF band’s pre-amplifier 2 Outputs the transmit signal switching control signal for the RX-B circuit. signal. HFOFB TRVSM High : The pre-amplifiers are OFF.
Page 35
3-7-22 BUFFER IC (MAIN UNIT; IC251) 3-7-24 SERIAL/PARAMETER IC (RXPLL-A UNIT; IC1) Port Description number name Port Description number name Outputs the bandpass filter (B7) selecting signal during transmit. Outputs the strobe signals to the 1st TXB7 PST2A High : W h i l e t r a n s m i t t i n g o n LO PLL IC on the RXPLL-A unit.
Page 36
3-7-27 DDS IC (RXPLL-B UNIT; IC101) 3-7-29 D/A CONVERTER IC (MAIN UNIT; IC331) Port Description Port number name Description number name Outputs the AF gain control signal for AFGVS1 Outputs the 1st LO muting signal to sub band (primary control). the RXPLL-B unit.
Page 37
3-7-31 CPLD IC (LOGIC UNIT; IC52) 3-7-33 EXPANDER IC (TENKEY BOARD; IC2) Port Port Description Description number name number name 60, 61 Outputs [PBT CLEAR] LED for main 63–68, IMS0–IMS8 Output the matrix/strobe signals. band control signal. MPCD Low : While using the PBT function in main band.
Page 38
3-7-34 SERIAL/PARAMETER IC 3-7-35 EXPANDER IC (DISPLAY BOARD; IC1) (DISPLAY BOARD; IC7) Port Description number name Port Description number name Input port for [AGC] control signal for MAGL main band. Outputs [TUNER] LED control signal. TN1D Low : While tuning. Input port for [AGC] control signal for SAGL sub band.
Page 39
3-7-38 EXPANDER IC (DISPLAY BOARD; IC4) Port Description number name Input por t for [CLEAR], [DUAL WATCH] and [SPLIT]. Input port for both main and sub bands [APF/TPF]. Input port for both main and sub bands [FILTER] and [PBT CLEAR]. Input port for both main and sub bands [NOTCH], [RIT] and [Δ...
Page 40
3-8 IF AND LO FREQUENCIES LIST 3-8-1 MAIN AND SUB 1ST LO FREQUENCIES LIST (FOR RECEIVING) MODE MAIN 1ST LO FREQUENCY (MHz) SUB 1ST LO FREQUENCY (MHz) 64.4865–124.4565 64.5865–124.5565 64.4835–124.4535 64.5835–124.5535 64.4850–124.4550 64.5850–124.5550 RTTY 64.48483–124.45483 64.58483–124.55483 PSK31 64.4850–124.4550 64.5850–124.5550 64.4850–124.4550 64.5850–124.5550 64.4850–124.4550 64.5850–124.5550...
Page 41
3-8-5 1ST IF FREQUENCIES LIST (FOR TRANSMITTING) MODE 1ST IF FREQUENCY (MHz) 64.45650 64.45350 64.45500 RTTY 64.45483 PSK31 64.45500 64.45500 64.45500 3-8-6 1ST LO FREQUENCIES LIST (FOR TRANSMITTING) BAND (MHz) LO FREQUENCY (MHz) BAND (MHz) LO FREQUENCY (MHz) 66.2580–66.2800 66.2580–66.2800 66.3625–66.3675 66.3625–66.3675 67.9550–68.0300...
Page 42
SECTION 4 ADJUSTMENT PROCEDURES 4-1 PREPARATION BEFORE SERVING REQUIRED TEST EQUIPMENTS EQUIPMENT GRADE AND RANGE EQUIPMENT GRADE AND RANGE AC outlet Voltage : 85–265 V Frequency range : 300–3000 Hz Audio generator Measuring range : 1–500 mV Measuring range : 250–300 W RF power meter Frequency range : 1.8–100 MHz...
Page 43
4-2 OSC UNIT ADJUSTMENTS ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST REFERENCE • Set the OSC unit to the external C o n n e c t a n R F Maximum voltage Adjust OUTPUT reference mode on the set mode. voltmeter to J72.
Page 44
• OSC UNIT TOP VIEW • LOCATION Front panel OSC unit (upper side) -Reference output check point -REF IN output check point -REF OUT output check point -REF IN output check point -REF OUT output check point REF OUT output check point Reference output adjustment 4 - 3...
Page 45
4-3 RXPLL-A UNIT ADJUSTMENTS ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST 40M OUTPUT • MAIN display frequency Maximum voltage Adjust C o n n e c t a n R F : 0.030 MHz PLL-A voltmeter to CP701 PLL-A repeatedly •...
Page 46
• LOCATION • RXPLL-A UNIT TOP VIEW Front panel RXPLL-A unit (lower side) L702 40 M output adjustment L703 CP701 40 M output check point C272 HPL lock voltage C262 check point C252 HPL lock voltage C154 C242 adjustment LPL lock voltage adjustment C232 C222 LPL lock voltage check point...
Page 47
(3.0 dBm ±3.0 dB) PLL-A repeatedly (T2LO). • Mode : USB L565, • Receiving L566 Pre-set the IC-7800 as the following C o n n e c t 4.5 V ±0.1 V SENSITIVITY R1101 condition. PLL-A voltmeter to CP1102. PLL-A •...
Page 48
• RXPLL-A UNIT TOP VIEW • LOCATION Front panel RXPLL-A unit (lower side) 2LO lock voltage check point C546 2LO lock voltage adjustment J561 T2LO output check point L566 T2LO output adjustment L565 L801 R2LO lock voltage L834 adjustment J831 R2LO lock voltage check point L1408 RX sensitivity...
Page 49
RXPLL-A UNIT ADJUSTMENTS–Continued ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST IMAGE • MAIN display frequency Rear C o n n e c t a n A C Minimum audio level Adjust RESPONSE : 14.150 MHz panel m i l l i vo l t m e t e r t o PLL-A repeatedly...
Page 50
• LOCATION • RXPLL-A UNIT TOP VIEW Front panel RXPLL-A unit (lower side) Image response C1656 adjustment R1516 L1222 RX sensitivity adjustment (50MHz) C1265 IF through adjustment 4 - 9...
Page 51
4-4 RXPLL-B UNIT ADJUSTMENTS ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST 40M OUTPUT • Dualwatch : ON C o n n e c t a n R F Maximum voltage Adjust • SUB display frequency PLL-B voltmeter to CP701 PLL-B repeatedly...
Page 52
• LOCATION • RXPLL-B UNIT TOP VIEW RXPLL-B unit (lower side) Front panel L702 40 M output adjustment L703 CP701 40 M output check point C272 HPL lock voltage C262 check point C252 HPL lock voltage C154 C242 adjustment LPL lock voltage adjustment C232 C222 LPL lock voltage check point...
Page 53
L565, • Mode : USB L566 • Receiving R1101 C o n n e c t Pre-set the IC-7800 as the following 4.5 V ±0.1 V voltmeter to CP1102. SENSITIVITY condition. PLL-B PLL-B C o n n e c t...
Page 54
• LOCATION • RXPLL-B UNIT TOP VIEW RXPLL-B unit (lower side) Front panel 2Lo lock voltage check point C546 2LO lock voltage adjustment J561 2LO output check point L566 2LO output adjustment L565 C1656 Image response R1516 adjustment L1408 RX sensitivity L1058 adjustment (HF) R1101...
Page 55
RXPLL-B UNIT ADJUSTMENTS–Continued ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST • SUB display frequency Rear C o n n e c t a n A C Maximum audio level L1222 SENSITIVITY : 50.020 MHz panel millivolt meter to [EXT PLL-B (50 MHz) Ω...
Page 56
• LOCATION • RXPLL-B UNIT TOP VIEW RXPLL-B unit (lower side) Front panel L1222 RX sensitivity adjustment (50MHz) C1265 IF through adjustment (50MHz) 4 - 15...
Page 57
4-5 PA200W BOARD ADJUSTMENTS ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST IDLING • Preset R301, R407 and R410 on PA200W C o n n e c t 1.0 A higher from the PA200W R301 CURRENT the PA200W unit to max. CCW.* ammeter between W1 previous value of the (For driver)
Page 58
• LOCATION • PA200W BOARD TOP VIEW PA200W board (upper side) Front panel Idling current R407 R425 adjustment (final) EP501 Idling current check point R426 R410 R301 Idling current Idling current adjustment (final) adjustment (driver) DC ammeter 4 - 17...
4-6 TUNER ADJUSTMENT ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST 1 • Main display frequency CTRL C o n n e c t Minimum voltage CTRL C104 DETECTOR : 24.950 MHz v o l t m e t e r •...
Page 60
• LOCATION • CTRL BOARD TOP VIEW CTRL board (upper side) Front panel CP101 SWR detector check point C104 SWR detector adjustment 4 - 19...
Page 61
4-7 MAIN UNIT ADJUSTMENTS ADJUSTMENT MEASUREMENT POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST MAXIMUM • Turn the power OFF MAIN C o n n e c t a d i g i t a l 0.5 V ±0.2 V MAIN OUTPUT •...
Page 62
• PA200W BOARD TOP VIEW • LOCATION DC ammeter PA200W board (upper side) MAIN unit (lower side) EP501 Id-APC check point Front panel • MAIN UNIT TOP VIEW L505 Maximum output power adjustment R538 Tx total gain adjustment L512 Maximum output power adjustment C576 Maximum output power adjustment Default adjustment...
Page 63
POINT ADJUSTMENT ADJUSTMENT CONDITION VALUE UNIT LOCATION UNIT ADJUST S3 LO LOCK 2.5 V Pre-set the IC-7800 as the following SCOPE Connect a digital SCOPE C824 VOLTAGE condition. voltmeter to CP801. • MAIN display frequency : 14.200 MHz • Mode : CW •...
Page 64
• LOCATION • SCOPE UNIT TOP VIEW SCOPE unit (lower side) Front panel R416 Scope gain adjustment C824 S3 LO voltage adjustment CP801 S3 LO voltage check point Scope attenuator adjustment Scope adjustment L201 L202 L203 4 - 23...
4-9 SOFTWARE ADJUSTMENTS ADJUSTMENT ADJUSTMENT CONDITION DISPLAY OPERATION ENTERING • Enter the adjustment mode: Push [F-2 (REF)], [F-3 (TX)] or [F-4 (RX)] to ADJUST MODE ADJUSTMENT q Turn power OFF. select each adjustment mode. MODE w Terminate [REMOTE] jack with Once entering adjustment mode, use [F-1 ] to a 2-conductor 3.5(d) mm mini-...
Page 66
SOFTWARE ADJUSTMENTS–Continued ADJUSTMENT ADJUSTMENT CONDITION DISPLAY OPERATION DRIVE LEVEL • Connect an audio generator to [MIC] Push [F-7 (SET)] to set the DRIVE level and DRIVE connector and set as; selects the next adjustment item. Frequency : 1.5 kHz Vd METER Vd48V Push [F-7 (SET)] to set the Vd meter indication Level...
Page 67
NOTE: Adjustment the reference return to the opening screen. frequency at least 5 minutes has been past from the IC-7800’s main power (on the rear panel) is turned After adjustment exiting from the adjustment mode when the transceiver is power OFF.
SECTION 5 PARTS LIST [REPLACEMENT UNITS] [VR-C BOARD] ORDER NO. UNIT NAME ORDER DESCRIPTION LOCATION 0325900101 U 7800 BPF 7210003160 VAR RV-317 (RK0972210) 0325900102 U 7800 RXPLL-A 7210003160 VAR RV-317 (RK0972210) 0325900103 U 7800 RXPLL-B 7030003520 S.RES ERJ3GEYJ 472 V (4.7 k) 28.6/2.7 7030003520 S.RES ERJ3GEYJ 472 V (4.7 k) 27.8/8.4...
Page 130
• WIRE CONNECTION INFORMATION WIRE No. CONNECTION1 CONNECTION2 *WIRE No. CONNECTION1 CONNECTION2 REF. No DISPLAY BOARD J203 LOGIC UNIT J805 LOGIC UNIT J826 MAIN UNIT J901 DISPLAY BOARD J3 SW-A BOARD J3 LOGIC UNIT J810 MAIN UNIT J451 W51~65 DISPLAY BOARD J6 VR-A BOARD J1 LOGIC UNIT J815 RXPLL-B UNIT J2...
Page 134
• FRONT AND BOTTOM SIDE MP12 (C) MP6 (C) LOGIC UNIT MP125 (C) MP135 (C) MEMORY UNIT MP42 (DC) MP902 (S) MP123 (C) J902 (S) MAIN UNIT MP901 (S) J902 (S) MP3 (S) J904 (S) MP1 (C) MP62 (DC) MP1 (ME) MP122 (DC) J903 (S) MP2 (ME)
Page 140
8-2 SW-A BOARD 8-4 SW-C BOARD • TOP VIEW • TOP VIEW MAIN FILTER FILTER VOX/BK-IN MAIN POWER PBT CLEAR PBT CLEAR TRANSMIT MAIN DIGI-SEL DIGI-SEL MONI MAIN TUNER APF/TPF APF/TPF MAIN AGCVR AGCVR NOTCH NOTCH MAIN TIMER ∆TX CLEAR DUAL SPLIT WATCH...
Page 141
• BOTTOM VIEW (SW-C BOARD) • BOTTOM VIEW (SW-A BOARD) 3R3V 3R3V SP1A SP1B MIGL KYSL SP2A PWRL DELL SP2B MAGL SAGL MSQL SSQL SNCL SAPL 3R3V PITL MSQL 3R3V MAGL PWRL to the VR-B board J1 to the VR-C board J1 to the PBT2 board J1 MIGL SSQL...
Page 142
8-5 VR-A BOARD 8-6 VR-B BOARD 8-7 VR-C BOARD • TOP VIEW • TOP VIEW • TOP VIEW KEY SPEED MAIN MIC/ AGC/SQL /DELAY AGC/SQL RF PWR MAIN NB/NR SUB NB/NR MAIN AF/RF SUB AF/RF Horizontal Horizontal Horizontal to the SW-A to the SW-A board J2 board J1...
Page 143
• BOTTOM VIEW (VR-C BOARD) • BOTTOM VIEW (VR-B BOARD) • BOTTOM VIEW (VR-A BOARD) MSND SQLS PHNI DSHK DOTK MUDL SAFL SRFL MAFL MRFL SNRL SNBL MNRL MNBL 3R3V to the DISPLAY board J6 PHOM PHOS DASH to the JACK board J1 MICE MSND SQLS...
Page 145
• BOTTOM VIEW (PBT1 BOARD) • BOTTOM VIEW (TENKEY BOARD) LDPS MTXD MRXD MLCD SPLD STXD SRXD SLCD to the LED board J1 3R3V MPWK MP1A MPRK MP1B XFCK MP2A MINK MP2B EQRK SUBK CHGK MNCL LDAT MAPL 3R3V LST1 to the PBT1 board J1 LDPS to the DISPLAY board J1...
Page 146
8-16 LOGIC UNIT +3R3V +3R3V CE01 +3R3V • TOP VIEW CE00 CE11 CE02 CE10 CE21 CE12 +3R3V +3R3V CE20 CE31 +3R3V CE22 CE30 VPEN CE32 J809 J808 J812 J824 J823 J820 J821 J805 BYTE# to the BPF unit J1 to the DISPLAY board J203 to the MAIN unit J900 to the MAIN unit J940 to the CHASSIS...
Page 150
8-18 MAIN UNIT J340 J404 J360 J142 • TOP VIEW T2LO from the RXPLL-A unit J561 REF IO SCPT from/to the OSC unit J71 to the SCOPE unit J11 to the RXPLL-B to the LOGIC unit J1501 unit J822 RELAY S/P DIF S/P DIF EXT-SP...
Page 158
8-22 RXPLL-A UNIT T2LO T1LO to the MAIN unit J502 to the MAIN unit J503 • TOP VIEW T3LO R1LO to the RXPLL-A unit J1101 to the MAIN unit J501 to the MAIN to the MAIN unit J400 unit J401 J1501 J1701 MP1653...
Page 160
8-23 RXPLL-B UNIT S2LO S2LO to the RXPLL-B unit J831 from the RXPLL-B unit J561 • TOP VIEW DACK S1LO to the RXPLL-B unit J1101 to the MAIN unit J399 to the MAIN to the MAIN unit J403 unit J404 J1501 J1701 MP1653...
Page 164
8-25 OSC UNIT • TOP VIEW M10M to the RXPLL-A unit J10 S10M to the RXPLL-B unit J10 to the LOGIC unit J814 REF IO from the MAIN unit J491 Horizontal 8 - 27...
Page 166
8-26 ANT-SW UNIT • TOP VIEW RX-ONLY RX-B to the BPF unit J108 to the BPF unit J506 Horizontal TX/RX-A from/to the CTRL board J301 to the FILTER unit J903 8 - 29...
Page 168
8-27 FILTER UNIT • TOP VIEW J905 J902 J903 to the CTRL board J53 to the CTRL board J52 DATA ANT4R +15V to the ANT-SW unit J4 Horizontal 8 - 31...
Page 170
8-28 NETWORK BOARD • TOP VIEW TUIN from/to the CTRL board J251 Horizontal TUOT from/to the CTRL board J252 to the TUNER unit MF3 to the CTRL board J51 8 - 33...
Page 172
8-29 CTRL BOARD to the NETWORK board J1 to the LOGIC unit J811 • TOP VIEW T15V T15V to the TUNER unit MF1/MF2 to the FILTER unit J905 TX/RX-A from/to the ANT-SW unti J1 TUOT from/to the NETWORK board J3 TUIN from/to the NETWORK board J2 to the FILTER unit J902...
Page 174
8-30 BPF UNIT • TOP VIEW RX-ONLY from the CTRL board J351 HF OUT-A 6m OUT-A RX-ANT to the DIGISEL unit J2 to the RXPLL-A unit J1201 from the ANT-SW unit J3 RXANT RXANT OUTA X-VERTER RXANT RXANT OUTB Horizontal HF OUT-B 6m OUT-B RX-B...
Page 176
8-31 PA200W BOARD • TOP VIEW from the MAIN unit J801 to the FILTER unit J901 Horizontal gray PAT8 from the REG unit black THML to the DC-DC to the MAIN unit J5 unit J430 8 - 39...
Page 177
• BOTTOM VIEW (PA200W BOARD) PA unit : MP20 PA unit : MP12 PA unit : MP20 Horizontal 8 - 40...
Page 178
8-32 DC-DC UNIT to the LOGIC unit J820 to the LOGIC unit J821 to the MAIN unit J450 • TOP VIEW to the PA200W board J5 C15V C15V LG_PWR to the REG unit Horizontal 8 - 41...
Page 182
FRONT UNIT DISPLAY UNIT LOGIC UNIT IC201/Q203/204 Q201/202 IC204/IC206 IC202/Q209/Q210 TC7SSET08/2SC4081/2SB1201 2SC3647 EDTCB23QAF ADV7123/SN74ACT04 TC7SET08/2SB1201/2SC4081 BRIGHT DC/AC Video INVERT CTRL CTRL MONITOR IC401 CF_BOARD PCI1410APGE IC404 RTL8139C Card CF_CARD BusC EtherC IC403 MAIN DIAL BR93LC46 IC610 FRONT CPU MAIN CPU2 MAIN CPU1 EEPROM HN58X2464...
Page 188
11-12 SW-C BOARD 11-13 PBT1 BOARD 11-14 PBT2 BOARD PBT2 BOARD PBT1 BOARD SW-C BOARD 3.30V 3.30V MAIN FILTER 0.00V MAIN DIGISEL 0.00V turn left turn right turn left turn right SUB FILTER 0.802V SUB DIGISEL 0.805V 3.3V 3.3V MAIN PBT 1.667V MAIN APF/TPF 1.658V...
Page 189
11-16 LOGIC UNIT AND MEMORY BOARD LOGIC UNIT (1) VDD3R3 VDD3R3 VDD3R3 VDD3R3 VDD3R3 VDD3R3 VDD3R3 VDD3R3 VDD1R5 VDD1R5 VDD1R5 VDD1R5 VDD1R5 BUS LINE1 3.17V 1 30 1 30 1 40 1 40 VDD3R3 VDD3R3 VDD3R3 VDD3R3 BUS LINE2 VDD3R3 VDD3R3 VDD3R3 VDD3R3...
Page 197
11-19 DSP-TX BOARD DSP-TX BOARD D3R3VL D3R3VL D3R3VL AFIN AFIN AFIN AFIN AFIN J921 R304 100 A15V A15V A15V A15V R341 AFIN R903 R804 R874 ANVOX R401 R412 V+ IC301 V+ IC341 4.7k 4.7k NJM5534MD NJM5534MD 1.2mV V+ IC801 IC871 2.27V R344 4.7k...
Page 198
11-20 SCOPE UNIT SCOPE UNIT (1) MESUREMENT CONDITIONS Explanatory notes voltage at RX(no instruction) frequency: 14.1 MHz mode: J3E(USB) DTC114EU MAIN VOLTAGE LINE ANT(RX): no input 6.46V 0.0V C35 0.01 (TX): no modulation 0.0V 6.47V from RXPLL-A SCPA SCPA SCOPE ATT: 0dB 0.0V 5.68V unit J1301...
Page 199
SCOPE UNIT (2) 3.03V L722 L721 3R3V 1.28V R721 R720 MESUREMENT CONDITIONS Explanatory notes voltage at RX(no instruction) frequency: 14.1 MHz mode: J3E(USB) VOLTAGE LINE ANT(RX): no input (TX): no modulation C727 Q720 SCOPE ATT: 0dB 2SC4406 Digital tester 0.0047 2.88V range: input impedance 0.75V...
Page 205
11-22 DIGISEL UNIT DIGISEL UNIT (A) RF OUT RF OUT RF OUT RF OUT RF OUT RF OUT to RXPLL-A unit J1002 Explanatory notes VOLTAGE LINE 0.0047 RX LINE FTR-B4CA012Z +15V +15V C137 120p C128 0.5p C138 100p RL67 RL58 FTR-B4CA012Z FTR-B4CA012Z +15V...
Page 206
DIGISEL UNIT (B) CP502 RF OUT-B RF OUT-B RF OUT-B RF OUT-B RF OUT-B J501 RF OUT-B RF OUT-B to RXPLL-B unit J1002 CP501 Explanatory notes C535 VOLTAGE LINE 0.0047 RL502 RX LINE FTR-B4CA012Z +15V +15V CP504 C637 120p C628 0.5p C638 100p...
Page 207
11-23 OSC UNIT OSC UNIT S10M to RXPLL-B unit J10 0.0047 -0.6dBm 2SC4081 0.0047 M10M to RXPLL-A unit J10 0.0047 0.0047 RL11 FTR-B4CA012Z DTC114EU 5.00V 10.21V 2SC4215 CR-772. IC10 12.02V 2SC4081 BA12FP REF V HF50ACC322513 3.3k 5.00V DTC114EU DTC114EU 2SC4081 LS-476 LS-476 RL10...
Page 208
11-24 ANT-SW UNIT 11-25 FILTER UNIT ANT-SW UNIT Explanatory notes FILTER UNIT VOLTAGE LINE TX LINE ANT1G ANT1G CP51 L804 L802 50MHz L803 TX/RX-A signal J901 from/to CTRL J904 from PA200W to CTRL CTIN CTIN board J301 ANT1 LA-589 LA-589 LA-590 LA-253 board J401...
Page 209
11-26 BPF UNIT BPF UNIT (1) BUS LINE1 J101 HF OUT-A to DIGISEL unit J2 +15V +15V +15V +15V +15V +15V +15V +15V +15V L231 +15V +15V R351 R354 +15V +15V +15V L234 C241 C245 L236 LR-456 LR-456 4.12V HF50A ATT12A ATT12A L232...
Page 210
11-27 NETWORK BOARD BPF UNIT (2) BUS LINE1 NETWORK BOARD 3.25V Explanatory notes RL40 +15V BPOE VS-12MBU VOLTAGE LINE VHDWA R907 VHDWIA BPCKA R141 BPCKA TUIN TUIN from/to CTRL VPR2A R906 VPR2IA BPSTA R142 BPSTA board J251 TX LINE R101 BI0A BPDAT R143...