D Command Table - Icom IC-9700 Reference Manual

Remote control
NOTE:
Operation of some control dials overrides CI-V commands. If a control dial, such as the AF Volume dial that has
a mark on it, is rotated after sending a CI-V command, the command will be overwritten by the operation.

D Command table

Cmd. Sub cmd. Data
00 See p. 13 Send the frequency data (transceive)
01 See p. 13 Send the mode data (transceive)
See p. 13 Read the band edge frequencies
02
* 1
See p. 13 Read the operating frequency
03
* 1
See p. 13 Read the operating mode
04
* 1
See p. 13 Set the operating frequency
05
* 2
See p. 13 Set the operating mode
06 *
2
07 Select the VFO mode
00 Select VFO A
( In the satellite mode, selects the VFO
01 Select VFO B
(In the satellite mode, "FA" (NG) is returned.)
A0 Equalize VFO A and VFO B
B0 Exchange MAIN and SUB Bands
D0 Select the main band
D1 Select the sub band
D2* 00 Send/read main band selection
01 Send/read sub band selection
Select the Memory mode
08
* 2
0001 to 0099 Select the Memory channel (Including the
satellite mode)
(0001=M-CH01, 0099=M-CH99)
0100 to 0105 Select program scan edge channel
1A/1B to 3A/3B
( 0100/0101 (1A ch/1B ch),
0106, 0107 Select call channel C1/C2
(0106 (C1 ch), 0107 (C2 ch))
09 Memory write
0A Memory copy to VFO
0B Memory clear
See p. 13 Read frequency offset
0C
* 1
*2
0D See p. 13 Send frequency offset
0E 00 Cancel the scan
01 Start a Programmed/memory scan
02 Start a Programmed scan
03 Start a ∂F scan
12 Start a Fine programmed scan
13 Start a Fine ∂F scan
22 Start a Memory scan
23 Start a Select memory scan
24 Start a Mode Select scan
Select ∂F scan span
Ax
* 2
(x=1 to 7) ( x=1 (±5 kHz), x=2 (±10 kHz),
x=3 (±20 kHz), x=4 (±50 kHz),
x=5 (±100 kHz), x=6 (±500 kHz),
x=7 (±1 MHz))
Clear the Select channel setting
B0
* 2
Set as select channel
B1
* 2
( The previously set number by CI-V is set
01 to 03 Set the channel as a Select channel
(01=SEL1, 02=SEL2, 03=SEL3)
00 to 03 Set the Select memory scan channel
2
B2 *
(00=ALL, 01=SEL1, 02=SEL2, 03=SEL3)
Set Scan resume OFF
D0
* 2
Set Scan resume ON (Close&Delay)
D3
* 2
*1
0F 00 Read Split OFF setting
01 Read Split ON setting
11 Read DUP– operation
12 Read DUP+ operation
13 Read DD Repeater Simplex mode (RPS)
Set Split function OFF
00
* 2
Set Split function ON
01
* 2
Description
mode.)
0104/0105 (3A ch/3B ch))
after turning power ON, or "1" is selected if
no selection is performed.)
Cmd. Sub cmd. Data
0F
10
* 2
11
* 2
12
* 2
13
* 2
10* 00 to 11
11* 00
10
13 00
01
02
14* 01 0000 ~ 0255 Send/read the AF level
02 0000 ~ 0255 Send/read the RF gain level
03 0000 ~ 0255 Send/read the squelch level
06 0000 ~ 0255 Send/read the NR level
07 0000 ~ 0255 Send/read [TWIN PBT] (PBT1) position
08 0000 ~ 0255 Send/read [TWIN PBT] (PBT2) position
09 0000 ~ 0255 Send/read CW pitch (5 Hz steps)
0A 0000 ~ 0255 Send/read RF power
0B 0000 ~ 0255 Send/read MIC gain
0C 0000 ~ 0255 Send/read keying speed
0D 0000 ~ 0255 Send/read Notch filter setting
0E 0000 ~ 0255 Send/read the COMP level
0F 0000 ~ 0255 Send/read the Break-IN Delay setting
12 0000 ~ 0255 Send/read NB level
15 0000 ~ 0255 Send/read Monitor audio [MONI] level
16 0000 ~ 0255 Send/read the VOX gain
17 0000 ~ 0255 Send/read the Anti VOX gain
19 0000 ~ 0255 Send/read LCD backlight brightness
01 00 or 01
15
* 1
02 0000 to 0255 Read S-meter level
05 00 or 01
07 00 or 01
11 0000 ~ 0255 Read the PO meter level
4
Description
Set the simplex operation
Set DUP– operation
Set DUP+ operation
Set DD Repeater Simplex mode (RPS)
Send/read the tuning step
( 00=OFF (10 Hz or 1 Hz),
01=100 Hz, 02=500 Hz, 03=1 kHz,
04=5 kHz, 05=6.25 kHz, 06=10 kHz,
07=12.5 kHz, 08=20 kHz, 09=25 kHz,
10=50 kHz, 11=100 kHz)
Send/read attenuator OFF setting
Send/read 10 dB attenuator setting
Speech all data with voice synthesizer
(S meter level, frequency and mode)
Speech the operating frequency and S meter
level by voice synthesizer
Speech the operating mode by voice synthesizer
L The mode is announced after the ongoing
speech.
(0000=Minimum to 0255=Maximum)
(0000=Minimum to 0255=Maximum)
(0000=Minimum to 0255=Maximum)
(0000=0%, 0255=100%)
( 0000=max. Counter Clockwise, 0128=center,
0255=max. Clockwise)
( 0000=max. Counter Clockwise, 0128=center,
0255=max. Clockwise)
( 0000=300 Hz, 0128=600 Hz, 0255=900 Hz)
( 0000=Minimum to 0255=Maximum)
(0000=Minimum to 0255=Maximum)
(0000=6 WPM to 0255=48 WPM)
( 0000=max. Counter Clockwise, 0128=center,
0255=max. Clockwise)
(0000=0 to 0255=10)
(0000=2.0 d to 0255=13.0 d)
(0000=0% to 0255=100%)
(0000=0% to 0255=100%)
(0000=0% to 0255=100%)
(0000=0% to 0255=100%)
(0000=0% to 0255=100%)
Read noise or S-meter squelch status
(00=Close, 01=Open)
(0000=S0, 0120=S9, 0241=S9+60 dB)
Read various squelch (tone squelch, and so
on) status
(00=Close, 01=Open)
Read the OVF status
( 00=OVF indicator is OFF, 01=OVF indicator is ON)
(0000=0% to 0143=50% to 0213=100%)