Table of Contents
Advertisement
Chapter 18
Installing the System Software
When downloaded, the system software is stored in the temporary storage area of the HDD. At the end of downloading, the main power switch must be turned off
and then back on, thus restarting the machine and writing the system software to both system area and flash ROM from the temporary storage area. When the main
power switch is turned off and then back on once again, the machine will start up using the new system software.
Writing takes place.
3)
<<<<< do
<<<<< download shell >>>>>
wnload shell >>>>>
[ SYSTEM JPja-m ] - - - -
[ SYSTEM JPja-m ] - - - -
[ SYSTEM ZZ ] - - - - - - -
[ SYSTEM ZZ ] - - - - - - -
[ SYSTEM JPja-w ] - - - -
[ SYSTEM JPja-w ] - - - -
[ SYSTEM ZZ ] - - - - - - -
[ SYSTEM ZZ ] - - - - - - -
[ FONT F ] - - - - - - - - - -
[ FONT F ] - - - - - - - - - -
[ FONT G ] - - - - - - - - - -
[ FONT G ] - - - - - - - - - -
+++ Switch OFF the power then ON.
+++ Switch OFF the po
18.1.4 Points to Note at Time of Downloading
iR C3380i / iR C3380 / iR C2880i / iR C2880 / iR C3580 / iR C3580i / iR C3080i
Do Not Turn Off the Power During Download/Write Operation
Do not turn off the power while the system software is being downloaded/written. Otherwise, the machine may fail to start up when its power is turned back on. (If
such is the case, execute HDD formatting, and download the system software. In the case of a boot ROM, replace the DIMM-ROM.)
Points to Note About Upgrading the DC Controller/Reader Controller
The DC controller/reader controller may be downloaded in either in normal mode or in safe mode. If done in safe mode, however, the controller version information
cannot be obtained, causing the data retained by the SST to be written over. It is a good idea, therefore, to use normal mode (so that the software will not be replaced
with software of a previous version).
18.2 Making Preparations
18.2.1 Installing the System Software (System CD -> SST)
iR C3380i / iR C3380 / iR C2880i / iR C2880 / iR C3580 / iR C3580i / iR C3080i
Here, you will be copying the system software found on the System CD to the SST.
[Preparatory Work]
Requirements
- PC installed with SST version 3.22 or later
- System CD for this machine
[Installing the System Software]
1) Turn on the PC.
2) Set the System CD in the PC.
18-6
Status of reception (sample)
- - - Do
- - - Download Mode - - -
wnload Mode - - -
[ iR2270i-JPjaxxxx-MN.dsh ] - - - - xx%
[ iR2270i-JPjaxxxx-MN.dsh ] - - - - xx%
System
Software
2)
The main power switch is turned off and then on.
HDD
Upg
Upgrading complete
ading complete
Upgrading complete
Upg
ading complete
Upg
Upgrading complete
ading complete
Upgrading complete
Upg
ading complete
Upg
Upgrading complete
ading complete
Upg
Upgrading complete
ading complete
er then ON. +++
+++
System
Software
Temporary
storage area
System area
Boot
ROM
FLASH
ROM
1)
The system software is downloaded.
- - - Download Mode - - -
- - - Do
wnload Mode - - -
[ iR2270i-JPjaxxxx-MN.dsh ] - - - - - - - - - -
[ iR2270i-JPjaxxxx-MN.dsh ] - - - - - - - - - -
[ iR2270iM-JPjaxxxx-1F77-MN.PRG ] - - - -
[ iR2270iM-JPjaxxxx-1F77-MN.PRG ] - - - -
[ iR2270iM-ZZjaxxxx-49AD.PRG ] - - - - - - -
[ iR2270iM-ZZjaxxxx-49AD
[ iR2270iW-JPjaxxxx-5C16-MN.PRG ] - - - -
[ iR2270iW
-JPjaxxxx-5C16-MN.PRG ] - - - -
[ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - -
[ iR2270iW
-ZZjaxxxx-A825.PRG ] - - - - - - -
[ iR2270iF-JPjaxxxx-DE96-ICC.PRG ] - - - -
[ iR2270iF-JPjaxxxx-DE96-ICC
[ iR2270iW
[ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - -
-ZZjaxxxx-A825.PRG ] - - - - - - -
[ iR2270iG-JPjaxxxx-EC30-ICC
[ iR2270iG-JPjaxxxx-EC30-ICC.PRG ] - - - -
HDD
System
Software
Temporary
storage area
4)
The main motor switch
is turned off and then on.
The machine starts up using
5)
the new version.
F-18-3
Complete
Complete
Complete
Complete
.PRG ] - - - - - - -
Complete
Complete
Complete
Complete
Complete
Complete
.PRG ] - - - -
Complete
Complete
Complete
Complete
.PRG ] - - - -
Complete
Complete
0014-4489
0014-4490
Advertisement
Chapters
Table of Contents
