Canon iR C2880 Series Service Manual page 515

Code Main Cause/Detail of Detection
***: Finisher-Z1 ****: Finisher-Y1, Saddle Finisher-Y2 *****: Puncher Unit
E243 Control panel unit error
0000 Communication between the main controller and the control panel unit is
abnormal.
E244 Error in connection of the flexible cable on the DC controller PCB
0000 Error in connection of the flexible cable on the DC controller PCB (right side
(1 pc.))
0001 Error in connection of the flexible cable on the DC controller PCB (left side (3
pc.))
E248 Backup memory error
0000 Check error of the SRAM PCB (at start up)
0001 Reader controller EEPROM error at power-on
0002 Reader controller EEPROM writing error
0003 Reader controller EEPROM reading error after check error writing
E315 Abnormality of image data
000e Data is corrupt (Abnormality of memory/HDD)
Soft decode error
E351 Main controller PCB error
0000 Communication error of the main controller PCB occurs at start-up.
E400 Feeder communication error
0001 Checksum error
0002 Reception status error
0003 Reception interrupt error
E413 Pressure motor trouble
0001 Pressure HP sensor OPEN
0002 Pressure HP sensor CLOSE
E490 Error in different feeder model
0001 Feeder for other model is detected.
E500 Finisher communication error
0001 Communication error is detected between the main body and the finisher for
specific times and specific period of time.
E503 *** Finisher internal communication error
0002 Communication error between the finisher and the saddle unit
0003 Communication error between the finisher and the puncher unit
E505 Finisher backup memory error
0001 Data stored in the backup memory is abnormal.
**** 0002 Abnormality of puncher unit EEPROM data
0003 Finisher controller EEPROM writing error
0004 Finisher controller EEPROM writing timeout error
E508 Error in different model
0001 At start-up, when the pickup/delivery option for different model is detected.
E514 *** Stack delivery error / **** End assist motor error
*** 8001 The HP sensor fails to be ON within 1500ms after the return belt starts to move
to its HP.
*** 8002 The HP sensor fails to be OFF within 1500ms after the return belt starts to
move to the belt contact position.
**** 8001 The HP sensor fails to be OFF after the end assist motor rotates for a specific
period of time.
**** 8002 The HP sensor fails to be ON after the end assist motor rotates for a specific
period of time.
E519 **** Gear change motor error
8001 The HP sensor fails to be OFF after the gear change motor rotates for a specific
period of time.
8002 The HP sensor fails to be ON after the gear change motor rotates for a specific
period of time.
E530 *** Rear alignment error / **** Front alignment error
Countermeasures
Check on connection between the main controller PCB and the
control panel unit
Check the connection of the flexible cable, replace the DC
controller PCB
Check on connection of the SRAM PCB, Replace the SRAM
PCB
Replace the reader controller PCB
Replace the image memory (SDRAM) , Replace the HDD
Disconnect and connect the main controller PCB (sub SJ-A/
PDRM-EF-A/R-A), or replace it.
Replace the main controller PCB (main).
- Check the connection of the cable
- Check on connection between the ADF controller PCB and the
main controller PCB (sub), Replace the ADF controller PCB,
Replace the main controller PCB (sub)
Replace the pressure motor.
Connect an appropriate feeder
Check on connection between the DC controller PCB and the
finisher controller PCB, Replace the finisher controller PCB,
Replace the DC controller PCB
Check on connection between the saddle stitcher controller
PCB and the finisher controller PCB, Replace the finisher
controller PCB, Replace the saddle stitcher controller PCB
Check on connection between the puncher controller PCB and
the finisher controller PCB, Replace the finisher controller
PCB, Replace the puncher controller PCB
Check on connection between the DC controller PCB and the
finisher controller PCB, Replace the finisher controller PCB,
Replace the DC controller PCB
Check on connection between the puncher controller PCB and
the finisher controller PCB, Replace the finisher controller
PCB, Replace the puncher controller PCB
Replace the finisher controller PCB
Replace to the supported pickup option (side paper deck),
delivery option (finisher) for this model.
Check on a drive of the stack retaining roller, Replace the return
belt U-turn HP sensor (SR5) , Replace the stack delivery motor
(M2)
Replace the end assist HP sensor (PI39) , Replace the end assist
motor (M39)
Replace the gear change HP sensor (PI49) , Replace the gear
change motor (M40)
Chapter 16
16-5