Boss BR-1180 Owner's Manual page 182

MIDI Implementation
Hours Count xyyzzzzz
x Reserved (0)
yy Time Code type
* The time code types defined by the MIDI specification correspond to the BR-1180/
1180CD Sync parameter "MTC Type" as follows.
MIDI specification setting
0 = 24 Frames / Sec
1 = 25 Frames / Sec
2 = 30 Frames / Sec (Drop Frame)
3 = 30 Frames / Sec (Non Drop Frame
zzzzz
Song Position Pointer
Status 2nd byte
F2H mmH
mm, ll=value: 00 00H - 7F 7FH (0 - 16383)
* The current position is transmitted by the Song Position Pointer Message when the BR-
1180/1180CD is stopped, or the locate operation has been performed, if the SYNC
parameter "Gen." is set to "MIDI CLOCK."
System Realtime Messages
Timing Clock
Status
F8H
* Transmitted when "Gen." is "MIDI CLOCK" in the SYNC parameter.
Start
Status
FAH
* Transmitted when "Gen." is "MIDI CLOCK" in the SYNC parameter.
Continue
Status
FBH
* Transmitted when "Gen." is "MIDI CLOCK" in the SYNC parameter.
Stop
Status
FCH
* Transmitted when "Gen." is "MIDI CLOCK" in the SYNC parameter.
Active Sensing
Status
FEH
* This is transmitted at intervals of approximately 200 msec.
System Exclusive Messages
Universal Non-realtime System Exclusive Message
Identity Reply Message
Receiving Identity Request Message, the Fantom send this message.
Status Data byte
F0H 7EH, dev, 06H, 02H, 41H, 55H, 01H
00H, 00H, 00H, 00H, 00H, 00H
F0H 7EH, dev, 06H, 02H, 41H, 55H, 01H, 01H F7H
00H, 00H, 00H, 00H, 00H
Byte Remarks
F0H Exclusive status
7EH Universal System Exclusive Non-realtime Header
dev Device ID (dev: 10H - 1FH)
06H Sub ID#1 (General Information)
02H Sub ID#2 (Identity Reply)
41H ID number (Roland)
55H 01H Device family code
00H/01H 00H Device family number code
00H 00H: BR-1180 (without CD-R/RW drive)
01H 00H: BR-1180CD (with internal CD-R/RW drive)
182
"MTC Type" setting
24
25
29D
29N or 30
Hours (0-23)
3rd byte
llH
Status
F7H
BR-1180
(without CD-R/RW drive)
BR-1180CD
(with internal CD-R/RW drive)
00H 00H 00H 00H Software revision level
F7H EOX (End of Exclusive)
* For instructions on setting the device ID, refer to "How to set the device ID" (p. 179).
Universal Realtime System Exclusive Message
MIDI Machine Control (MMC)
Status Data byte
F0H 7FH, Dev, 06H, aaH, ..., bbH
Byte Remars
F0H Exlusive Status
7FH Universal System Exclusive Realtime Header
Dev Device ID
06H MMC command message
aaH command
: :
bbH command
F7H EOX (End of Exclusive)
STOP (MCS)
Status Data byte
F0H 7FH, dev, 06H, 01H
Byte Remarks
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC command message
01H STOP (MCS)
F7H EOX (End of Exclusive)
* If the transport switch [STOP] was pressed, the BR-1180/1180CD transmits this message.
DEFERRED PLAYÅiMCSÅj
Status Data byte
F0H 7FH, 7FH, 06H, 03H
Byte Remarks
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC command message
03H DEFERRED PLAY (MCS)
F7H EOX (End of Exclusive)
* If the transport switch [PLAY] was pressed, the BR-1180/1180CD transmits this
message.
RECORD STROBE
Status Data byte
F0H 7FH, 7FH, 06H, 06H
Byte Remarks
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC command message
06H RECORD STROBE
F7H EOX (End of Exclusive)
* If the transport switch [REC] was pressed out of the recording condition, the BR-1180/
1180CD transmits this message.
RECORD EXIT
Status Data byte
F0H 7FH, 7FH, 06H, 07H
Byte Remarks
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC command message
07H RECORD EXIT
F7H EOX (End of Exclusive)
* If the transport switch [REC] was pressed while recording, the BR-1180/1180CD
transmits this message.
Status
F7H
Status
F7H
Status
F7H
Status
F7H
Status
F7H