Omron CJ Series Operation Manual page 275

maximum I/O response time ....................................... 5-52
memory used for the CJ-series Unit ...............5-2, 5-6, A-2
message communications ............................................ 6-2
message communications specifications ...................... 6-2
message monitoring timer ............................................. 6-3
minimum I/O response time ........................................ 5-59
mode number switch (MODE) ....................................... 2-8
MS indicator ................................................................ 1-35
multidrop connections ................................................. 3-15
multi-power supply ...................................................... 4-30
Multi-wiring Connector ................................................ 1-19
N
network wiring ............................................................... 3-4
NS indicator ................................................................ 1-35
O
Open Type Connector .......................................... 1-19, 4-7
P
peripheral devices ......................................................... 4-2
power supply wiring .................................................... 4-30
preparing and mounting Flat Connectors .................... 4-16
programless communications ....................................... 1-6
R
recommended CompoNet Cables ............................... A-26
Registered Slave Unit Participation
Monitoring Time ....................................................... 5-18
Registered Slave Unit Participation
Standby Mode .......................................................... 5-18
Registration Table Enable Setting ................................. 2-9
Registration Table Mode Flag ..................................... 5-32
Registration Table Verification Error Flag .................... 5-31
Registration Tables ..................................................... 5-16
remote I/O communications ........................................ 5-13
remote I/O communications performance ................... 5-52
Remote I/O Communications Start Switch ................. 5-13
Remote I/O Communications Started Flag ................. 5-32
Repeater Unit Communications Error Flag ................. 5-32
Repeater Unit Node Slave Unit Duplicated
Address Error Flag ................................................... 5-32
Repeater Units ....................................................... 1-3, 1-6
Representative Alarm Status Flag .............................. 5-32
Representative Warning Status Flag .......................... 5-32
rotary switches ............................................................ 5-36
Round Cable I ............................................... 1-9, 1-16, 3-9
Round Cable II .............................................. 1-9, 1-16, 3-9
S
segments ...................................................................... 1-5
SendCmd instruction ................................................... 6-10
sending explicit messages ................................... 6-4, 6-10
settings ............................................................... 5-12, 5-33
NJ-series Instructions Reference Manual (W502)
seven-segment display ......................................... 1-36, 2-5
Slave Unit allocations .................................................. 5-34
Slave Unit allocations for communications
mode number 8 ........................................................ 5-49
Slave Unit Duplicated Address Error ........................... 5-19
Slave Unit Duplicated Address Error Flag ................... 5-30
Slave Units .................................................................... 1-3
Smart Slave Unit Functions .......................................... 1-7
Special Tool ........................................................ 1-19, 4-17
status ................................................................. 5-12, 5-30
status information ........................................................ 5-11
stopping communications at communications errors .... 1-8
switch settings ............................................................... 2-7
Sysmac Studio .......................................... 1-23, 1-33, 5-36
system configuration example ....................................... 1-2
system configuration patterns ....................................... 1-6
system-defined variables ............................................ 6-12
T
T-branching ................................................................. 3-14
Terminating Resistors ........................1-3, 1-20, 3-17, 4-14
trunk line-branch line formation ..................................... 3-2
trunk lines ...................................................................... 1-3
types of cables ............................................................ 1-28
types of CompoNet Network node addresses ............ 5-35
U
Unit Configuration .............................................. 1-23, 1-33
unit number switches (MACH No.) ................................ 2-7
unrestricted wiring formation ......................................... 3-2
user-defined variables ................................................... 5-4
W
wiring formations ........................................................... 3-2
Index
I
Index-3