System Settings; Initial Settings - Furuno FS-1562 Manual

2. System settings

2.1 Initial Settings

This section provides how to set up the following items.
1. Ship's ID number
2. DSC block settings
VHF block settings
3.
Protection OFF
Refer to section "2.2Changing system settings".
TEST VHF ch70
manual
[SELECT] [9]
System < Rom version >
V P ID DSC RT CH PO L
Select "ID" press the [ENT] key.
Refer to section "5 changing ID
Enter own identification
and Private mode".
[digits] MMSI: - - - - - - - - -
Enter own ship's ID and the [ENT] key twice.
DSC : Receiver < CH70 >
CH70 [1] VHF [2]
When two FM-8500s are installed, designate
one as Main (CH70) and the other as Sub (VHF).
The default setting is "CH70" as mainunit.
Select "CH70" or "VHF" press the [ENT] key.
DSC : remote DMC ON
ON [1] OFF [2]
Select whether DMC-5 is connected or not.
(ON:connected)
Select "ON" or "OFF" and press the [ENT] key twice.
RT1-Mode : USA/WX < OFF >
ON [1] OFF [2]
Disable or enable the USA/WX mode.
Select "ON" or "OFF" and press the [ENT] key .
RT1-Mode : private < OFF >
OFF [1] ON [2]
Disable or enable the PRIVATE channel mode.
Select "ON" or "OFF" and press the [ENT] key.
RT2-Hook work : CH16 < ON >
ON [1] OFF [2]
Disable or enable watch on CH16 when handset is on hook.
Select "ON" or "OFF" and press the [ENT] key.
RT2-Hook work : SP < ON >
ON [1] OFF [2]
Disable or enable speaker when handset is on hook.
Select "ON" or "OFF" and press the [ENT] key .
(*1)
4. Channel system settings
5. Selection of LCD display, Japanese or English
6. Protection (on/off)
Refer to section "5.Changing ID and
Private mode".
(*1)
RT3-Time out timer < OFF >
OFF [1] ON [2]
Disable or continue after a long transmission.
For USA, set to ON, Not effective unless USA mode is enabled.
Select "ON" or "OFF" and press the [ENT] key .
RT4-TX AF monitor < OFF >
OFF [1] ON [2]
Disable or enable monitoring of external equipment;
For example, Remote Station RB-700 is monitored.
Select "ON" or "OFF" and press the [ENT] key.
RT5-Auto 1W < ON >
ON [1] OFF [2]
ON:Automatic setting of 1W when selecting the low output power
channel set by "Channel Preset" operation.
Select "ON" or "OFF" and press the [ENT] key .
RT6-Dual watch < ON >
ON [1] OFF [2]
Disable or enable dual watch.
Select "ON" or "OFF" and press the [ENT] key .
RT6-Scanning < ON >
ON [1] OFF [2]
Disable or enable channel scanning.
Select "ON" or "OFF" and press the [ENT] key .
RT7-Auto SQ <L00 H03 H030>
LOW= 00 HIGH HOLD
Settings auto SQ function (*better not change these value)
LOW:Enter lowest limt of voice frequency which open
automatic SQ. Enter value by the following formula.
HIGH:Enter highest frequency which opens automatic SQ.
HOLD:Enter SQ hold time in two digits, by follwing the formula.
Press the [ENT] key 4 times .
*
INTL CH:016 < TX SIMP HI >
ENABLE= TX[1] RX[2] UN[3]
(continued next page)
E4-2
OFF !!
*You had better not change these value.
Setting value x 50 = Low Frequency
Setting value x 50 = Hi Frequency
Setting value x 20 msec= Time desired
FM-8500