Mitsubishi Electric FR-E800 Series Instruction Manual page 88

 (G) Control parameters
Parameters for motor control.
Pr. group Pr.
G000 0 Torque boost
G001 3 Base frequency
G002 19 Base frequency voltage
G003 14 Load pattern selection
G010 46 Second torque boost
G011 47 Second V/F (base frequency)
Energy saving control
G030 60
selection
SF-PR slip amount adjustment
G060 673 operation selection [200/400 V
class]
SF-PR slip amount adjustment
G061 674
gain [200/400 V class]
DC injection brake operation
G100 10
frequency
DC injection brake operation
G101 11
time
G102 802 Pre-excitation selection
G103 850 Brake operation selection
G106 250 Stop selection
Special regenerative brake
G107 70
duty
DC injection brake operation
G110 12
voltage
Regeneration avoidance
G120 882
operation selection
Regeneration avoidance
G121 883
operation level
Regeneration avoidance
G123 885 compensation frequency limit
value
Regeneration avoidance
G124 886
voltage gain
Regeneration avoidance
G125 665
frequency gain
G200 800 Control method selection
G203 245 Rated slip
Slip compensation time
G204 246
constant
Constant output range slip
G205 247
compensation selection
Constant output range torque
G210 803
characteristic selection
G211 820 Speed control P gain 1
G212 821 Speed control integral time 1
Torque control P gain 1
G213 824 (current loop proportional
gain)
Torque control integral time 1
G214 825
(current loop integral time)
*1
G215 Speed detection filter 1
823
G217 854 Excitation ratio
Speed feed forward control/
G220 877 model adaptive speed control
selection
G221 878 Speed feed forward filter
Speed feed forward torque
G222 879
limit
G223 881 Speed feed forward gain
Refer
Name
to page
Simple Simple Simple 426
Simple Simple Simple 428
428
430
426
428
432
433
433
434
434
434
434
440
442
434
446
446
446
446
446
97
449
449
449
114,
143
121
121
149
149
154
155
124
124
124
124
Pr. group Pr.
G224 828 Model speed control gain
G230 840 Torque bias selection
G231 841 Torque bias 1
G232 842 Torque bias 2
G233 843 Torque bias 3
G234 844 Torque bias filter
G235 845 Torque bias operation time
Torque bias balance
G236 846
compensation
Fall-time torque bias terminal 4
G237 847
bias
Fall-time torque bias terminal 4
G238 848
gain
*1
G240 Speed feedback range
367
*1
G241 Feedback gain
368
Second motor control method
G300 451
selection
G311 830 Speed control P gain 2
G312 831 Speed control integral time 2
Torque control P gain 2
G313 834 (current loop proportional
gain)
Torque control integral time 2
G314 835
(current loop integral time)
*1
G315 Speed detection filter 2
833
G400 286 Droop gain
G401 287 Droop filter time constant
G410 653 Speed smoothing control
Speed smoothing cutoff
G411 654
frequency
Speed control gain (Advanced
G932 89
magnetic flux vector)
Second motor speed control
G942 569
gain
*1 The setting is available when a plug-in option for Vector
control is installed.
*2 On the LCD operation panel used as the command source,
the parameter number in parentheses appears instead of that
starting with the letter C.
*3 For the Ethernet model and the safety communication model,
the setting is available only when the FR-A8AY is installed.
*4 For details, refer to the Instruction Manual (Communication).
*5 Available when the PLC function is enabled. (Pr.313 to
Pr.315 are always available for settings in the Ethernet model
and the safety communication model.)
*6 For the standard model, the setting is available only when a
communication option is installed.
*7 For details, refer to the FR-E800-SCE Instruction Manual
(Functional Safety).
3.4 Parameter list (by function group number)
Refer
Name
to page
124
126
126
126
126
126
126
126
126
126
450
450
97
121
121
149
149
154
452
452
453
453
102
102
87
3. Parameters
1
2
3
4
5
6
7
8
9
10