Mitsubishi Electric FR-E800 Series Instruction Manual page 273

Incremen
Monitor item
t and unit
Motor load factor 0.1%
Cumulative
0.01 kWh
*8
energy
Torque command 0.1%
Torque current
0.1%
command
Feedback
—
*10
pulse
Trace status 1
PLC function user
monitor 1
PLC function user
Increment
monitor 2
set in the
register
SD1215
PLC function user
monitor 3
Station number
1
(PU)
Station number
1
(CC-Link)
Power saving Increment
effect and unit
vary
depending
Cumulative
on the
energy saving
parameter
settings.
PID set point 0.1%
PID measured
0.1%
value
PID deviation 0.1%
Input terminal
—
status
Output terminal
—
status
Option input
—
*10
terminal status
Option output
—
*10
terminal status
272
12. (M) Item and Output Signal for Monitoring
12.2 Monitor item selection on operation panel or via communication
Communication
Pr.
Monitor Monitor
setting
*1
code 1 code 2
24 H18 40224
25 H19 40225
32 H20 40232
33 H21 40233
35 H23 40235
38 H26 40238
40 H28 40240
41 H29 40241
42 H2A 40242
44 H2C 40244
45 H2D 40245
50 H32 40250
51 H33 40251
52 H34 40252
53 H35 40253
54 H36 40254
*11 *11
H0F 40215
*18
55
*12 *12
H10 40216
56 — —
57 — —
Negative
Monitor
indicatio
number
*4
*2
n (-)
*3
The output current value is displayed as a
percentage, considering the inverter rated
18 current value as 100%.
Readout (%) = present output current value /
inverter rated current value × 100
The cumulative energy based on the monitored
19 output power is displayed. Use Pr.170 to reset it.
(Refer to
The torque command value adjusted with Vector
20 ○
control is displayed.
The command value of the current for torque is
21 ○
displayed.
The number of pulses fed back from the encoder
in one cycle of the sampling is displayed (kept
displayed during a stop). (The output voltage is
displayed when a vector control option is not
installed.)
23
The sampling time period varies depending on
the Pr.369 Number of encoder pulses setting.
1050 or less: 1 s,
1051 to 2100: 0.5 s,
2101 to 4096: 0.25 s
The trace status is displayed. (Refer to
26
418.)
The user-designated monitor item is displayed
28
using the PLC function.
Each value of the following special registers is
29
displayed.
SD1216: displayed with the setting value "40",
SD1217: displayed with the setting value "41",
SD1218: displayed with the setting value "42"
2A
(Refer to the PLC Function Programming
Manual.)
The station number of the inverter enabling
communication via the PU connector is
2C
displayed. (Available only for the standard
model.)
The station number of the inverter enabling CC-
2D Link communication is displayed. ("0" is
displayed when the FR-A8NC is not installed.)
32 The energy saving effect monitoring is enabled.
The item to monitor is selectable from among
the saved power, the average energy saving,
and the energy cost savings. Some of them can
33
be displayed as a percentage according to the
parameter settings. (Refer to
34
The set point, measured value, and deviation
35 during PID control operation is displayed. (Refer
to page
36 ○
The ON/OFF state of the input terminals on the
F inverter is displayed. (Refer to
details of indication on the operation panel.)
The ON/OFF state of the output terminals on the
10 inverter is displayed. (Refer to
details of indication on the operation panel.)
The ON/OFF state of the input terminals on the
digital input option (FR-A8AX) is displayed on
—
the operation panel. (Refer to
details.)
The ON/OFF state of the output terminals on the
digital output option (FR-A8AY) or the relay
—
output option (FR-A8AR) is displayed on the
operation panel. (Refer to
Description
page 276.)
page 286.)
389.)
page 275
page 275
page 275
page 275 for details.)
page
for
for
for