Mitsubishi Electric FR-E800 Series Instruction Manual page 86

Pr. group Pr.
Amplitude compensation
A303 595
amount during acceleration
A304 596 Amplitude acceleration time
A305 597 Amplitude deceleration time
A600 759 PID unit selection
A601 131 PID upper limit
A602 132 PID lower limit
A603 553 PID deviation limit
A604 554 PID signal operation selection
Integral stop selection at
A607 1015
limited frequency
A610 128 PID action selection
A611 133 PID action set point
PID control automatic
A612 127
switchover frequency
A613 129 PID proportional band
A614 130 PID integral time
A615 134 PID differential time
Output interruption detection
A621 575
time
Output interruption detection
A622 576
level
Output interruption cancel
A623 577
level
PID set point/deviation input
A624 609
selection
PID measured value input
A625 610
selection
C42
A630 PID display bias coefficient
*2
(934)
C43
A631 PID display bias analog value
*2
(934)
C44
A632 PID display gain coefficient
*2
(935)
C45
A633 PID display gain analog value
*2
(935)
Automatic restart after
A700 162 instantaneous power failure
selection
Rotation direction detection
A701 299
selection at restarting
A702 57 Restart coasting time
A703 58 Restart cushion time
Stall prevention operation
A710 165
level for restart
A711 298 Frequency search gain
A712 560 Second frequency search gain
A730 261 Power failure stop selection
PLC function operation
A800 414
selection
Inverter operation lock mode
A801 415
setting
Refer
Name
to page
378
378
378
393
380,
396
380,
396
380
380
380
380,
396
380,
396
380
380,
396
380,
396
380,
396
380
380
380
380,
396
380,
396
393
393
393
393
403,
408,
410
403
403,
408
403
403
345,
410
345,
410
414
416
416
Pr. group Pr.
PLC function flash memory
A804 498
clear
User parameter auto storage
A805 675
function selection
A810 to 1150 to PLC function user parameters
A859 1199 1 to 50
A900 1020 Trace operation selection
A902 1022 Sampling cycle
A903 1023 Number of analog channels
A904 1024 Sampling auto start
A905 1025 Trigger mode selection
Number of sampling before
A906 1026
trigger
A910 1027 Analog source selection (1ch)
A911 1028 Analog source selection (2ch)
A912 1029 Analog source selection (3ch)
A913 1030 Analog source selection (4ch)
A914 1031 Analog source selection (5ch)
A915 1032 Analog source selection (6ch)
A916 1033 Analog source selection (7ch)
A917 1034 Analog source selection (8ch)
A918 1035 Analog trigger channel
Analog trigger operation
A919 1036
selection
A920 1037 Analog trigger level
A930 1038 Digital source selection (1ch)
A931 1039 Digital source selection (2ch)
A932 1040 Digital source selection (3ch)
A933 1041 Digital source selection (4ch)
A934 1042 Digital source selection (5ch)
A935 1043 Digital source selection (6ch)
A936 1044 Digital source selection (7ch)
A937 1045 Digital source selection (8ch)
A938 1046 Digital trigger channel
Digital trigger operation
A939 1047
selection
 B: Position control parameters
Parameters for the position control setting.
Pr. group Pr.
B003 422 Position control gain
 N: Communication operation
parameters
Parameters for the setting of communication operation such
as the communication
characteristics.
Pr. group Pr.
N000 549 Protocol selection
Communication EEPROM
N001 342
write selection
Communication reset
*6
N010
349
selection
Stop mode selection at
N013 502
communication error
3.4 Parameter list (by function group number)
Refer
Name
to page
416
416
416
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
418
Refer
Name
to page
434
specifications or operating
Refer
Name
to page
*4
*4
*4
*4
3. Parameters
1
2
3
4
5
6
7
8
9
10
85