Mitsubishi MELSEC Q Series User Manual page 239

Input signal error detection setting ............... 3-59
Input signal error detection extended setting
....................................................................... 3-59
Inrush current .................................................. 3-2
Installing ........................................................... 5-2
Insulation resistance ................................ 3-1, 3-2
Intelligent function module parameter ............ 5-7
Internal current consumption ................... 3-1, 3-3
Isolation method ....................................... 3-1, 3-2
[L]
List of I/O signals .................................. 3-28, 3-29
Low Voltage Directive ................................... A-12
[M]
Maximum and minimum values hold function
....................................................................... 3-16
Maximum and minimum values storage area
(16bit) ............................................................. 3-58
Maximum and minimum values storage area
(32bit) ............................................................. 3-62
Maximum number of writes for E
.................................................................. 3-1, 3-3
Maximum supply current ................................. 3-2
Maximum value/minimum value reset completed
flag ................................................................. 3-34
Maximum value/minimum value reset request
....................................................................... 3-35
MELSECNET/H ............................................... 2-1
Mode switching setting .................................. 3-67
Module ready ................................................. 3-30
Monitoring/test ............................................... 5-18
Move averaging ............................................. 3-13
Multiple CPU system ....................................... 2-1
[N]
Number of analog input channels ............ 3-1, 3-2
Number of I/O occupied points ................ 3-1, 3-3
Number of modules ......................................... 2-1
[O]
Offset value ..................................................... 3-4
Offset/gain setting ............. 4-11, 4-16, 5-19, 5-21
Offset/gain setting change completed flag ... 3-34
Offset/gain setting change request ............... 3-35
Offset/gain setting mode ............................... 3-58
Offset/gain setting mode flag ........................ 3-32
Online module change ............................. 2-2, 7-1
Index - 2
Open parameters ........................................... 5-12
Operating condition setting ............................ 5-19
Operating condition setting completed flag ... 3-31
Operating condition setting request .............. 3-35
Operating environment .................................... 5-4
[P]
Part identification nomenclature ...................... 4-3
Pass data ............................................. 5-25, 5-27
Pass data classification setting ..................... 3-67
Performance comparison ........................ App.-13
Performance specifications ..................... 3-1, 3-2
Primary delay filter ......................................... 3-14
Process alarm ................................................ 3-23
Process alarm upper/lower limit value .......... 3-62
Programming procedure .................................. 6-1
[Q]
Q62AD-DGH .................................................... 1-1
Q64AD-GH ....................................................... 1-1
QCPU (Q mode) ........................................... A-13
2
[R]
PROM
Rate alarm ...................................................... 3-24
Rate alarm upper/lower limit value ................ 3-64
Rate alarm warning detection period ............ 3-63
Read from PLC .............................................. 5-12
Reference accuracy ........................ 3-1, 3-2, 3-10
Remote I/O network ............................... 6-7, 6-20
Resolution ................................................ 3-1, 3-2
RUN LED ......................................................... 4-3
[S]
Sampling processing ..................................... 3-11
Save parameters............................................ 5-12
Screen for selecting a target intelligent function
module .............................................................. 5-9
Setting range .................................................. 3-57
Setup and procedures before operation ......... 4-2
Short circuit protection ............................. 1-1, 3-2
Software package ............................................ 2-2
Supply power ON/OFF function .................... 3-11
Supply voltage ................................................. 3-2
Switch setting for intelligent function module
........................................................................ 4-10
System monitor ................................................ 8-6
[T]
Temperature coefficient .................. 3-1, 3-2, 3-10
Ind
Index - 2