Oki MC363 Advanced Manual page 270

Item
PreFix
Received Time Stamp
Print Check Message
Duplex
Distant Station Priority
• Fax Setting
Item
Service Bit
Country Code
A/R Full Print
Daily Tx/Rx Log Report Setting
Print Time
Tone For Echo (For Transmission)
Tone For Echo (For Reception)
H/Modem Rate (For Tx)
H/Modem Rate (For Rx)
Factory Description
default
setting
(NULL) Sets the dialing prefix. You can enter up to 40
digits.
OFF Sets whether to print the time stamp on
received faxes.
ON Sets whether to report the error content if a
transmission error occurs.
OFF or Sets simplex or duplex for printing received
ON(Duplex) fax and the binding position for duplex
printing.
Type 1 Sets the priority order of information for
Distant Station (information of the
destination).
Priority (High > Low)
[Type 1]: Destination information > Name in
speed dial > Phone number
[Type 2]: Name in speed dial > Phone
number
Factory Description
default
setting
OFF If set to OFF, some menu items are not
displayed on the screen.
International or Sets the country code.
U.S.A
ON Sets whether to print the list of the
communication results automatically after
every 50 communications.
OFF Enables / disables to print a daily report.
0 Hour Sets the date and time for printing the daily
0 Minute report.
0 Second
Disable Displays only if Service Bit is ON.
Disable Displays only if Service Bit is ON.
33.6 Kbps Sets the default modem reception
transmission speed while the machine is
sending a fax.
33.6 Kbps Sets the default value of the modem
transmission speed while the machine is
receiving a fax.
Item
Attenuator
MF Attenuator
Pulse Make Ratio
Pulse Dial Type
MF(Tone) Duration
Calling Timer
PBX Line
Forwarding Forwarding Setting
Setting
Forwarding Number
TAD Mode
Tel Priority Mode
CNG Detection
- 270 -
9. Operating Management/ Specifications
Factory Description
default
setting
10 dB, Range: Enter Attenuator. Displays only if Service Bit
0 - 15 dB is ON.
8 dB, Range: 0 Enter MF(Tone) Attenuator. Displays only if
- 15 dB Service Bit is ON.
40%, Range: Sets to make rate of DP (10 pps) during call.
33, 39, 40% Displays only if Service Bit is ON and Tone /
Pulse setting is PULSE.
N, Range: N, Sets the pulse type for dialing. Displays only
10-N, N+1 if Service Bit is ON and Tone / Pulse setting
is PULSE.
100 mseconds, Enter MF(Tone) Duration. Displays only if
Range: 75, 85, Service Bit is ON and Tone / Pulse setting is
100 mseconds TONE.
60 mseconds, Displays only if Service Bit is ON.
Range: 1 -
255 seconds
OFF When connecting to PBX (internal
exchange), put it to [ON].
OFF Sets whether to enable the fax forwarding
mode.
(NULL) Sets a fax number used for the fax
forwarding mode.
Type 3 Sets an operation type in Tel / Fax Ready
mode.
[Type 3]: A fax signal is detected in
15 seconds from when the answering
machine answers. Normally, use this type.
[Type 1]: A fax signal is detected right after
the answering machine answers, and then
the reception starts. If you have any fax
reception problems, they may be improved if
this type is set.
[Type 2]: A fax signal is detected right after
the answering machine answers. Set this
type if you usually use this machine as a
phone.
OFF Sets when the external telephone and the
machine ring in Tel / Fax Ready mode.
[ON]: The sender is assumed to make a
voice call. The telephone rings early.
OFF Sets whether to determine whether the
sender is sending a fax during the off the
hook condition in Tel / Fax Ready mode.