Omron VARISPEED E7 User Manual page 92

Parame-
ter Num- Name
ber
Sets P-control proportional gain.
Proportional
b5-02 P-control is not performed when the set-
gain (P)
ting is 0.00.
Sets I-control integral time.
b5-03 Integral (I) time I-control is not performed when the set-
ting is 0.0.
Sets the I-control limit as a percentage of
b5-04 Integral (I) limit
the maximum output frequency.
Sets the limit after PI-control as a per-
b5-06 PI limit centage of the maximum output fre-
quency.
Sets the offset after PI-control as a per-
PI offset adjust-
b5-07 centage of the maximum output fre-
ment
quency.
Sets the time constant for low pass filter
PI delay time
b5-08 for PI-control output.
constant
Usually not necessary to set.
Selects forward/reverse direction for PI
PI output char-
output.
b5-09 acteristics selec-
0: PI output is forward.
tion
1: PI output is reverse
b5-10 PI output gain Sets output gain.
0: Limit to 0 when PI output is negative.
1: Reverses when PI output is negative.
PI reverse out-
b5-11 Limit to 0 is also active when reverse
put selection
prohibit is selected by
b1-04.
0: No detection of PI feedback loss.
1: Detection of PI feedback loss.
Selection of PI Operation continues during detection,
b5-12 feedback signal the fault contact is not operated.
loss detection 2: Detection of PI feedback loss.
The motor coasts to stop at detection,
and the fault contact operates.
Sets the PI feedback loss detection level
PI feedback loss
b5-13 as percentage using the maximum output
detection level
frequency as 100%.
PI feedback loss
b5-14 Sets the PI feedback loss detection time.
detection time
Sleep function Sets the sleep function start level as a fre-
b5-15
operation level quency.
Sleep operation Sets the delay time until the sleep func-
b5-16
delay time tion starts.
Accel/decel
Sets the accel/decel time for the PI Soft-
b5-17 time for PI ref-
starter (SFS).
erence
PI Setpoint 0: Disabled
b5-18
Selection 1: Enabled
b5-19 PI Setpoint PI-target value
Setting
Description
Range
0.00
to
25.00
0.0 to
360.0
0.0 to
100.0
0.0 to
100.0
-100.0
to
+100.0
0.00 to
10.00
0 or 1
0.0 to
25.0
0 or 1
0 to 2
0 to
100
0.0 to
25.5
0.0 to
200.0
0.0 to
25.5
0.0 to
25.5
0 to 1
0.00 to
100.00
%
Change
MEMO-
Factory during Access
BUS
Setting Opera- Level
Register
tion
1.00 Yes A 1A6H
1.0 s Yes A 1A7H
100.0% Yes A 1A8H
100.0% Yes A 1AAH
0.0% Yes A 1ABH
0.00 s Yes A 1ACH
0 No A 1ADH
1.0 No A 1AEH
0 No A 1AFH
0 No A 1B0H
0% No A 1B1H
1.0 s No A 1B2H
0.0 Hz No A 1B3H
0.0 s No A 1B4H
0.0 s No A 1B5H
0 No A 1DCH
0 Yes A 1DDH
5
5
5-