Extron electronics DTP CrossPoint 4K Series User Manual page 89

Command and Response Table for Matrix Switcher Commands (continued)
Command Function
Logo on and off
Assign a logo to an output
Example (DTP CrossPoint 108 4K):
Unassign a logo
View logo assignment
View all logo assignments
Captive screw and Ethernet serial port insertion enables
Enable an input captive screw serial
port insertion
Enable an input Ethernet serial port
insertion
Set all RS-232 input insertions
View input insertion
View all input insertions
Enable an output captive screw
serial port insertion
Enable an output Ethernet serial port
insertion
Set all RS-232 output insertions
View RS-232 output insertion
View all output insertions
Ethernet insertion serial port insert parameters
Set serial port parameters
Read serial port parameters
Configure current port timeout
Read current port timeout
Configure global IP port timeout
Read global IP port timeout
Set UART starting point
Read UART starting point
NOTE: X! = TP (scaled) and insertion output number
X2@ = TP and insertion input number
X2^ = Logo number
X4#
= Captive screw or UART
X4$ = Port number
X4% = Baud rate
X4^ = Parity
X4& = Data bits
X4* = Stop bits
X4( = Port timeout (in 10-sec. increments)
X5) = UART starting point (see
SIS Command Response
(Host to Unit) (Unit to Host)
Logo Commands
E X! X2^ }
E * LOGO LogoE
E }
E6*4LOGO LogoE6*4
E X! }
E *0LOGO LogoE
E X! } X2^]
E LOGO
E }
ELOGO 00
RS-232 Insertion Commands
E X2@ }
I *0LRPT LrptI
E X2@ }
I *1LRPT LrptI
E X4# }
I *LRPT LrptI
E X2@ } X4#]
I LRPT
E } X4#
ILRPT
E X! }
O *0LRPT LrptO
E X! }
O *1LRPT LrptO
E X4# }
O *LRPT LrptO
E X! } X4#]
O LRPT
E } X4#
OLRPT
EX4$ X4% X4^ X4& X4* }
* , , , CP
Cpn
EX4$ }
CP X4%
E X4( }
0* TC Pti0*
E } X4(]
0TC
E X4( }
1* TC Pti1*
E } X4(]
1TC
EX5) }
MD Pmd
E } X5)]
MD
See X! definition
See X2@
definition
–
01 16
= Captive screw RS-232 insert (default)
0
See X4$ definition
, ,
300 600 1200
, ,
28800 38400
dd, ven, one,
o e n
,
7 8
,
1 2
(= 10 seconds) -
1
X5) on page 70) The starting point (
The next positions (
The next positions (
DTP CrossPoint 4K Series Matrix Switchers • Programming Guide
Additional description
X! X2^]
Assign logo
*
] Assign logo 4 to output 6.
X! ]
*0 Set output
X2^
Logo
X2^ ] Up to four (n) 00s, which are not scaled
•
n y
outputs and up to four (y) 2-digit
which are the logo status of scaler outputs.
X2@ ] Enable the captive screw serial port insert,
*0
on input
X2@ ] Enable the Ethernet serial port insert on
*1
X2@
input
serial port insert.
X4#]
X4# X4# X4# ]
Two or four
w x y z
matrix size, one for each TP input.
X! ]
Enable the captive screw serial port insert,
*0
on output
insert.
X! ] Enable the Ethernet serial port insert on
*1
output
serial port insert.
X4#]
X4# X4# X4# ]
Two or four
w x y z
matrix size, one for each TP output.
X4$ X4% X4^ X4& X4*]
•Ccp , , ,
, , ,
X4^ X4& X4*]
X4(]
X4(]
X5)] Sets the initial (lowest) port number for
the range of numbers assigned to the
serial port and UARTs.
on page 69 for numbers by matrix size.
on page 69 for numbers by matrix size.
= Ethernet RS-232 insert (UART)
1
on page 69 for numbers by matrix size
, , , , , ,
1800 2400 3600 4800 7200
, (default= )
57600 115200 9600
ark, pace (only the first letter required) (
m s
(default is = 300 seconds = 5 minutes)
65000 30
X5) ) is the rear panel Remote RS-232 port.
X5) through X5) ) are DTP inputs.
+1 x
X5) through X5) ) are DTP outputs.
x+1 y
X2^ X!
to output .
X!
to output no logo.
X!
is assigned to output .
X2^
s,
X2@
, disabling the Ethernet insert.
, disabling the captive screw
X4#
s, depending on the
X!
, disabling the Ethernet
X!
, disabling the captive screw
X4#
s, depending on the
.
, , ,
9600 14400 19200
= default)
n
81