Extron electronics DTP CrossPoint 4K Series User Manual page 177

Command Function
Group masters
NOTES:
•
See Group masters on page 119, for more information about audio group masters.
•
A group must have assigned members for these commands to have an effect.
•
X8$
For , a positive (+) value is assumed unless a negative (-) value is specified.
•
X8$
If entering a value outside the valid range for the group or outside the soft limits, the DTP CrossPoint responds with an invalid
parameter ( ) error.
E13
Set a group fader control
Example:
Raise a group fader control
Example:
Lower a group fader control
View the group fader control level
Mute a group mute control
Clear (unmute) a group mute control
View a group mute control mute
Set soft limits
Example:
View soft limits
View group type
View group members
NOTE: X8) = Object ID (gain control or mix-point)
X8# = Group master group number
X8$ = Group fader setting
X8% = Group fader increment
X8^ = Group fader soft limit
X8& = Group type
SIS Command Response
(Host to Unit) (Unit to Host)
E X8# X8$ }
D * GRPM GrpmD
E }
D2*-293GRPM GrpmD2*-293
}
E X8# X8% GrpmD
D * +GRPM
E }
D2*30+GRPM GrpmD2*-263
E X8# X8% }
D * -GRPM GrpmD
E X8# }
D GRPM GrpmD
E X8# }
D *1GRPM GrpmD
E X8# }
D *0GRPM GrpmD
E X8# } X8@]
D GRPM
E X8^ X8^ X8^ }
L * * GRPM
upper lower
GrpmL
E }
L2*+60*-60GRPM
GrpmL2*60*–60
}
GrpmL
E X8^
L GRPM
E X8# }
P GRPM GrpmP
E X8# }
O GRPM
X8#
GrpmO
See OID table, beginning on page 161.
01 – 32
dB value, in 0.1 dB increments. The valid range depends on the type of gain block
dB value, in 0.1 dB increments, to raise or lower a group fader
dB value, in 0.1 dB increments.
X8^ must be within the range for the gain block grouped in
6= gain
DTP CrossPoint 4K Series Matrix Switchers • DSP SIS Commands
Additional description
X8# X8$] Set the group fader to a value of
*
] Set the group 2 fader control to
-29.3 dB.
X8# X8$]
Increase the level of the
*
X8%
by dB.
] Raise the group 2 fader 3 dB (from
-29.3 dB to -26.3 dB, starting from the
level set in the Set a group fader control
example, above.
X8# X8$]
* Decrease the level of the
X8%
fader by
X8# X8$] In verbose modes 1 and 2, the response
*
is simplified to
X8# ]
Mute all blocks in group
*1
X8# ]
*0 Umute all blocks in group
Set the groups soft limits to
X8^ X8^ X8^]
* *
Set the upper soft limit for the group 2
]
fader to +6.0 dB and the lower limit to
-6.0 dB.
X8^ X8^ X8^] In verbose modes 0 and 1, the response
* *
is simplified to
X8# X8&]
Show the group type (
*
X8#
. In verbose modes 0 and 1, the
response is simplified to
X8)
is the control or mix-point. In
verbose modes 0 and 1, the response is
X8) X8) X8) ]
* * *...*
1 2 16
simplified to
12 = mute
X8$ .
X8#
group fader
X8#
group
dB.
X8$]
.
X8#
.
X8#
.
X8^ X8^
and .
X8^ X8^]
* .
X8&
) for group
X8&] .
X8) X8) X8) ]
* *...* .
1 2 16
X8# .
169