Audio Input And Output Connections - Extron electronics DTP CrossPoint 4K Series User Manual

Audio Input and Output Connections

DTP CROSSPOINT 108 4K
COM 1 COM 2 COM 3 DIGITAL I/O
Tx Rx G RTS CTS Tx Rx G Tx Rx G 1 2 3 4 G
IR/SERIAL RELAYS eBUS
1 2 1 2 C 3 4 C +V +S -S G
R
S G S G PWR OUT = 6W
1 2 3 4
100-240V ~
3.0 A MAX
1 2 3
50-60 Hz
Figure 6.
1 2 3A 4A
3B
SIG LINK
XTP
DTP
OUT
HDBT
100-240V ~ 1.6 A MAX
1 2 3 4 5
50-60 Hz
Figure 7.
For inputs and outputs on captive screw connectors (see figure 6 and figure 7,
the connectors are included with the switcher, but you must supply the audio cable.
Audio inputs 1 through 6 — Connect balanced or unbalanced stereo audio
G
inputs to these 5-pole, 3.5 mm captive screw connectors (see
input connectors
Mic/Line inputs 1 through 4 — Connect microphones or other mono audio
H
inputs to these 3-pole, 3.5 mm captive screw connectors (see
connectors
+48 V (phantom power) LEDs — These LEDs light to indicate that +48 V
I
phantom power is applied to the associated mic/line inputs.
Audio outputs — Connect audio devices such as an audio amplifier or
J
powered speakers to these 4 or 2, 5-pole, 3.5 mm captive screw connectors.
These connectors output unamplified, line level audio, whether it is tied from
an analog input or de-embedded from an HDMI input (see
connectors
Amp output 1 (stereo audio model) — Connect unpowered, 4-ohm or
K
8-ohm speakers to this 4-pole 5 mm captive screw connector to play
the amplified stereo audio from audio output 1.
Amp output 1 (mono audio model) — Connect unpowered, high
L
impedence speakers to this 2-pole captive screw connector to play the
amplified mono audio from audio output 1.
ATTENTION:
•
•
N G
LAN 1
L R L R L R
1
3 5
2 4 6
L R L R L R
LAN 2 LAN 3 EXP
RS-232 IR
5A 6A 5B 6B 6
Tx Rx G Tx Rx
S/PDIF
SIG LINK OVER TP
SIG LINK
OUT
XTP XTP
RS-232 IR
DTP DTP
OUT Tx Rx G Tx Rx OUT
HDBT HDBT
RS-232 IR
4 5 6 7
Tx Rx G Tx Rx
SIG LINK
OVER TP
XTP
RS-232 IR
DTP IN
Tx Rx G Tx Rx
M
Audio Input and Output Connections and Indications, 10x8 Matrix
M
RS-232 IR COM 1
4B 4
Tx Rx G Tx Rx
Tx Rx G
REMOTE RTS CTS
SIG LINK S/PDIF
OVER TP
XTP OUT IR/SERIAL
RS-232 IR RESET
Tx Rx G
R 1
OUT DTP
Tx Rx G Tx Rx
HDBT S G S
RS-232 IR
6 7 8
Tx Rx G Tx Rx
SIG LINK SIG LINK
OVER TP
XTP
XTP
RS-232 IR
DTP
IN IN DTP
Tx Rx G Tx Rx EXP
N
Audio Input and Output Connections and Indications, 8x4 matrix
on page 21 to wire the connectors).
on page 22 to wire the connectors).
on page 22 to wire the connectors).
Ensure the rated input voltage of the speakers matches the rated output
voltage of the switcher.
Assurez-vous que la tension nominale d'entrée des enceintes soit compatible
avec la tension nominale de sortie du sélecteur.
DTP CrossPoint 4K Series Matrix Switchers • Installation
I H J K
8 / 4
+48V
L R L R 1
1
1 3 1 3
L R
MIC/LINE
2
2 4 2 4
L R L R
3
4
CLASS 2 WIRING
RS-232 IR REMOTE
RESET
7 8
Tx Rx G Tx Rx
SIG LINK OVER TP
SIG LINK
XTP XTP
RS-232 IR
HDBT HDBT
DTP DTP
OUT OUT
Tx Rx G Tx Rx Tx Rx G LAN
RS-232 IR
8 9 10
Tx Rx G Tx Rx
SIG LINK SIG LINK SIG LINK
OVER TP
XTP XTP XTP
RS-232 IR
IN DTP DTP IN IN DTP
Tx Rx G Tx Rx
K
COM 2 COM 3 DIGITAL I/O
LAN 1 8 / 4
1
Tx Rx G Tx Rx G 1 2 3 4 G L R
RELAYS DIGITAL I/O
2 1 2 C 3 4 C +V +V D -S +S
CLASS 2 WIRING
LAN 2 LAN 3
G PWR OUT = 6W
+48V
L R L R
L R L R L R 1 1 3
1 1 3
3 5
MIC/LINE
2
2 4 6 2 4 2 4
L R L R L R L R L R
3
4
G H J
I
Analog audio output
DTP CrossPoint IPCP SA
1
L
CLASS 2 WIRING
DTP CrossPoint IPCP MA
DTP CrossPoint IPCP SA
1
L
CLASS 2 WIRING
DTP CrossPoint IPCP MA
, , and ),
G H J
Analog audio
L R
Mic/Line input
+48V
1
L R
8 / 4
1
L R
CLASS 2 WIRING
1
CLASS 2 WIRING
15