Extron electronics CrossPoint 450 Plus 84 HV User Manual
  1. Manuals
  2. Brands
  3. Extron electronics Manuals
  4. Matrix Switcher
  5. CrossPoint 450 Plus 84 HV
  6. User manual

Extron electronics CrossPoint 450 Plus 84 HV User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
im Vertrieb von
www.camboard.de
CAMBOARD Electronics
CrossPoint 450 Plus Series
Tel. 07131 911201
Fax 07131 911203
MAV Plus Series
Matrix Switchers
ce-info@camboard.de
68-521-02 Rev. B
12 04

Advertisement

Table of Contents
loading

Related Manuals for Extron electronics CrossPoint 450 Plus 84 HV

Summary of Contents for Extron electronics CrossPoint 450 Plus 84 HV

  • Page 1 im Vertrieb von CAMBOARD Electronics CrossPoint 450 Plus Series MAV Plus Series Matrix Switchers 68-521-02 Rev. B 12 04 www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...
  • Page 2 im Vertrieb von CAMBOARD Electronics Precautions Safety Instructions • English Warning This symbol is intended to alert the user of important operating and maintenance Power sources • This equipment should be operated only from the power source indicated on the product.

  • Page 3: Front Panel Controls

    im Vertrieb von CAMBOARD Electronics Quick Start — CrossPoint 450 Plus and MAV Plus Switchers Installation RS-232 RS-422 All Models 84 — 1616 2412 — 3232 Step 1 Pin# Pin Function Function Function Transmit + — Not used — Not used Turn off power to the input and output devices, Transmit –...
  • Page 4 im Vertrieb von CAMBOARD Electronics Quick Start — CrossPoint 450 Plus and MAV Plus Switchers, Cont’d On audio models, the output buttons also Save or recall a preset display the selected input’s audio level. 1. Save a preset — Press and hold the Preset button for 2 seconds.

  • Page 5: Table Of Contents

    im Vertrieb von CAMBOARD Electronics Table of Contents Chapter 1 • Introduction ....................... 1-1 About this Manual ......................1-2 About the Matrix Switchers ..................1-2 CrossPoint 450 Plus switchers .................... 1-5 MAV Plus switchers ......................1-6 Definitions ..........................1-7 Features ...........................
  • Page 6 im Vertrieb von CAMBOARD Electronics Table of Contents, cont’d I/O grouping ........................3-21 Example 5: Grouping inputs and outputs ..............3-23 Setting RGB delay (CrossPoint 450 Plus switchers only) ..........3-25 ............3-25 Example 6: Setting the RGB delay for an output Using presets ........................
  • Page 7 im Vertrieb von CAMBOARD Electronics Command/Response Table for IP SIS Commands ..........4-16 Symbol definitions ......................4-16 Special Characters ......................4-18 Chapter 5 • Matrix Software ....................5-1 Matrix Switchers Control Program ................5-2 Installing the software ...................... 5-2 Software operation via Ethernet ..................5-2 ....................
  • Page 8 im Vertrieb von CAMBOARD Electronics Table of Contents, cont’d Chapter 6 • HTML Operation ....................6-1 Download the Startup Page ..................6-2 System Status Page ......................6-3 DSVP page (CrossPoint 450 Plus switchers only) .............. 6-4 System Configuration Page ................... 6-5 IP settings fields .........................
  • Page 9 im Vertrieb von CAMBOARD Electronics Appendix A • Ethernet Connection ................A-1 Ethernet Link ........................A-2 Ethernet connection ......................A-2 Default address ......................... A-2 Ping to determine Extron IP address ................Ping to determine Web IP address ..................Connect as a Telnet client ....................A-3 Telnet tips ...........................
  • Page 10 im Vertrieb von CAMBOARD Electronics Table of Contents, cont’d 68-521-02 Rev. B All trademarks mentioned in this manual are the properties of their respective owners. 12 04 www.camboard.de Tel. 07131 911201 ce-info@camboard.de CrossPoint 450 Plus and MAV Plus Switchers • Table of Contents Fax 07131 911203...

  • Page 11: Chapter 1 • Introduction

    im Vertrieb von CAMBOARD Electronics CrossPoint 450 Plus and MAV Plus Switchers Chapter One Introduction About this Manual About the Matrix Switchers Definitions Features www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...

  • Page 12: About This Manual

    im Vertrieb von CAMBOARD Electronics Introduction Introduction, cont’d About this Manual This manual contains installation, configuration, and operating information for the complete Extron family of full-function, medium- and large-sized, analog matrix switchers, specifically: • CrossPoint 450 Plus ultra-wideband RGBHV and audio matrix switchers •...
  • Page 13 im Vertrieb von CAMBOARD Electronics 16 Outputs Projector Sound System Projector Ethernet U TS U TP Monitor U TS U TP U TS Y IN C IN U TS IN P Extron Mav Plus 1616 HDA I.T. System Control Matrix Switcher 16 Inputs sive gres...
  • Page 14 im Vertrieb von CAMBOARD Electronics Introduction, cont’d In this manual, the term “video model” refers to any CrossPoint 450 Plus or MAV Plus switcher that switches video. In this manual, the term “audio model” refers to any CrossPoint 450 Plus or MAV Plus switcher that switches audio.

  • Page 15: Crosspoint 450 Plus Switchers

    im Vertrieb von CAMBOARD Electronics Each model has an internal 100 VAC to 240 VAC, 50/60 Hz, auto switchable power supply that provides worldwide power compatibility. The CrossPoint 450 Plus 2412, 2424, 3216, and 3232 and MAV Plus 2412, 2424, 3216, and 3232 each have two, primary and redundant, power supplies.

  • Page 16: Mav Plus Switchers

    im Vertrieb von CAMBOARD Electronics Introduction, cont’d MAV Plus switchers There are 56 different MAV Plus models available, in a combination of matrix sizes and low resolution video formats, with or without audio or with audio only. The various matrix sizes and video formats are as follows: •...

  • Page 17: Definitions

    im Vertrieb von CAMBOARD Electronics • MAV 3216 Plus (32 inputs by 16 outputs) • MAV 3232 Plus (32 inputs by 32 outputs) MAV Plus HDA and HD switchers can also route low resolution RGsB and RsGsBs video signals. HDA and HD switchers can also route multiple composite video planes or S-video and composite video.

  • Page 18: Features

    im Vertrieb von CAMBOARD Electronics Introduction, cont’d Features Video — All switchers input and output video on BNC connectors. CrossPoint 450 Plus — These switchers input and output wideband RGBHV or RGBS video. They can also switch RGsB, RsGsGs, component/HDTV, S-video, or composite video.
  • Page 19 im Vertrieb von CAMBOARD Electronics Digital Sync Validation Processing (DSVP™) (CrossPoint 450 Plus switchers) — In critical environments or unmanned, remote locations, it may be vital to know that sources are active and switching. Extron’s DSVP confirms that input sources are active by scanning all sync inputs for active signals. DSVP provides instantaneous frequency feedback for composite sync or separate horizontal and vertical sync signals via the switcher’s RS-232/RS-422 or Ethernet port.
  • Page 20 im Vertrieb von CAMBOARD Electronics Introduction, cont’d Operational flexibility — Operations such as input/output selection, setting of presets, and adjustment of audio levels can be performed on the front panel or via the Ethernet or RS-232/RS-422 link. The RS-232/RS-422 links allow remote control via a PC or control system.
  • Page 21 im Vertrieb von CAMBOARD Electronics Power — The matrix switchers’ 100 VAC to 240 VAC, auto-switchable, internal power supply(s) provides worldwide power compatibility. Primary and redundant power supplies — (CrossPoint 450 Plus and MAV Plus 2412, 2424, 3216, and 3232 switchers only) Includes two internal 100 VAC to 240 VAC, 50/60 Hz, auto-switchable power supplies, which provide worldwide power compatibility.
  • Page 22 im Vertrieb von CAMBOARD Electronics Introduction, cont’d www.camboard.de Tel. 07131 911201 ce-info@camboard.de 1-12 CrossPoint 450 Plus and MAV Plus Matrix Switchers • Introduction Fax 07131 911203...

  • Page 23: Chapter 2 • Installation

    im Vertrieb von CAMBOARD Electronics CrossPoint 450 Plus and MAV Plus Switchers Chapter Two Installation Mounting the Switcher Rear Panel Views Connections www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...

  • Page 24: Mounting The Switcher

    im Vertrieb von CAMBOARD Electronics Installation Installation, cont’d Mounting the Switcher The matrix switchers are housed in rack-mountable, metal enclosures with 19" rack ears. The amount of vertical rack space required for each switcher is as follows: • 2U high enclosure MAV Plus 84, 88, 124, and 128 HDA, HD, SVA, and SV switchers MAV Plus 84, 88, 124, 128, 816, 168, and 1616 AV, AV RCA, V, and A switchers...

  • Page 25: Rear Panel Views

    im Vertrieb von CAMBOARD Electronics Rear Panel Views All connectors for all switchers are on the rear panel. Figure 2-1 through figure 2-10 show a representative sampling of all of the matrix switchers described in this manual. See Connections, on page 2-8, for connecting cables to the rear panel connectors.
  • Page 26 im Vertrieb von CAMBOARD Electronics Installation, cont’d Figure 2-2 shows the CrossPoint 450 Plus 1616 HVA RGB video and stereo audio matrix switcher. The CrossPoint 450 Plus 816 and 168 are housed in the same 6U enclosure, but have fewer output connectors to accommodate their smaller matrix sizes. INPUTS OUTPUTS RESET...

  • Page 27: Mav Plus Switchers

    im Vertrieb von CAMBOARD Electronics MAV switchers Figure 2-4 shows the MAV Plus 3232 SVA S-video and stereo audio switcher. The MAV Plus 2412, 2424, and 3216 are housed in a similar 8U enclosure, but have fewer input and/or output connectors to accommodate their smaller matrix sizes.
  • Page 28 im Vertrieb von CAMBOARD Electronics Installation, cont’d Figure 2-6 shows a MAV Plus 1616 HDA component/HDTV video and stereo audio switcher. The rear panel of the MAV Plus 816 and 168 models have the same features as the MAV Plus 1616 series models (figure 2-6 and figure 2-7), with the exception of fewer inputs or outputs.
  • Page 29 im Vertrieb von CAMBOARD Electronics INPUTS OUTPUTS LISTED 1T23 I.T.E. Figure 2-8 — MAV Plus 128 AV RCA matrix switcher Figure 2-9 shows a MAV Plus 128 HDA component/HDTV video and stereo audio matrix switcher. The MAV Plus 88 models are housed in the same 2U enclosure, but have fewer input and/or output connectors to accommodate the different matrix sizes they provide.

  • Page 30: Connections

    im Vertrieb von CAMBOARD Electronics Installation, cont’d Connections Use Electrostatic discharge precautions (be electrically grounded) when CAUTION making connections. Electrostatic discharge (ESD) can damage equipment, even if you cannot feel, see, or hear it. Remove system power before making all connections. CAUTION Video input and output (video switchers) The switchers do not alter the video signal in any way.
  • Page 31 im Vertrieb von CAMBOARD Electronics Input 1 I N P U T S I N P U T S I N P U T S GREEN BLUE O U T P U T S O U T P U T S O U T P U T S O U T P U T S Output 1...

  • Page 32: Video (Mav Plus Switchers Only)

    im Vertrieb von CAMBOARD Electronics Installation, cont’d Video (MAV Plus switchers only) Video input and output connections are made with female BNC connectors. Some video input and output devices do not have BNC video output connectors. For these cases, a suitable cable or connector adapter is necessary. The part number for the Extron RCA-to-BNC adapter is 10-229-01.
  • Page 33 im Vertrieb von CAMBOARD Electronics MAV Plus 88, 128 SVA and SV S-video MAV Plus 816, 168, 1616 SVA and SV MAV Plus 2412, 2424, S-video 3216, 3232 SVA and SV S-video Figure 2-13 — MAV Plus S-video connections MAV Plus 88, 128 HDA and HD Composite video MAV Plus...

  • Page 34: Sync Termination Switchers (Crosspoint 450 Plus Only)

    im Vertrieb von CAMBOARD Electronics Installation, cont’d Sync termination switches (CrossPoint 450 Plus only) Sync termination switches — The CrossPoint 450 Plus matrix switchers have sync termination switches on the rear panel for inputs 1 through 8 (CrossPoint 450 Plus 2412, 2424, 3216, and 3232) or inputs 1 through 4 (CrossPoint 450 Plus 84, 88, 124, 128, 816, 168, 1616).

  • Page 35: Audio Input And Output (Audio Models Only)

    im Vertrieb von CAMBOARD Electronics Audio input and output (audio models only) By default, the audio ties follow the video ties. Audio breakaway, which can be activated via the front panel or under Ethernet or RS-232/RS-422 control, allows you to select from any one of the audio input sources and route it separately from its corresponding video source.

  • Page 36: Rca Connector Model (Mav Plus 128 Av Rca)

    im Vertrieb von CAMBOARD Electronics Installation, cont’d Connections for balanced and unbalanced audio outputs — These 3.5 mm, 5-pole captive screw connectors output the selected unamplified, line level audio. Connect audio devices, such as an audio amplifier or powered speakers. See figure 2-18 to properly wire an output connector. Ring See caution Sleeve...

  • Page 37: Ethernet

    im Vertrieb von CAMBOARD Electronics If desired, connect an MCP 1000 remote control panel master unit to the switcher’s RS-232/RS-422 connector. You can also connect an MKP 1000 remote keypad or MCP 1000 slave unit to the MCP 1000 master unit. Refer to the MCP 1000 Remote Control Panel User’s Manual and the MKP 1000 User’s Manual for details.
  • Page 38 im Vertrieb von CAMBOARD Electronics Installation, cont’d • 10Base-T Ethernet requires CAT 3 UTP or STP cable at minimum. • 100Base-T Fast Ethernet requires CAT 5e UTP or STP cable at minimum. The Ethernet cable can be terminated as a straight-through cable or a crossover cable and must be properly terminated for your application (figure 2-20).

  • Page 39: Reset Button

    im Vertrieb von CAMBOARD Electronics Reset button Reset button — The Reset button initiates three levels of reset to the matrix switcher. Press and hold the button while the switcher is running or while you power up the switcher for different reset levels.

  • Page 40: Power

    im Vertrieb von CAMBOARD Electronics Installation, cont’d Figure 2-22 shows another configuration, in which the timing source passes through three video cameras and a video scan converter before connecting to the switcher. This type of video camera is capable of synchronizing with the external timing source for video editing applications.

  • Page 41: Chapter 3 • Operation

    im Vertrieb von CAMBOARD Electronics CrossPoint 450 Plus and MAV Plus Switchers Chapter Three Operation Front Panel Controls and Indicators Front Panel Operations Rear Panel Controls Optimizing the Audio (Audio Switchers) Troubleshooting Configuration Worksheets www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...

  • Page 42: Front Panel Controls And Indicators

    im Vertrieb von CAMBOARD Electronics Operation Operation, cont’d The operation of the CrossPoint 450 Plus switchers and MAV Plus switchers is very similar. There are two exceptions: • The video selection button is labeled “RGBHV” on the CrossPoint 450 Plus switchers and “Video” on the MAV Plus switchers. •...
  • Page 43 im Vertrieb von CAMBOARD Electronics INPUTS 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 CONTROL 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 ENTER PRESET AUDIO VIEW VIDEO OUTPUTS...

  • Page 44: Definitions

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Definitions The following terms, which apply to Extron matrix switchers, are used throughout this manual: Tie — An input-to-output connection. Set of ties — An input tied to two or more outputs. (An output can never be tied to more than one input.) Configuration —...

  • Page 45: Control Buttons

    im Vertrieb von CAMBOARD Electronics Output buttons — The output buttons have two primary functions (•) and three secondary (❏) functions: • Select output(s). • Identify the selected output(s). ❏ (Output 1 only) With the Input 1 button, select I/O Group mode. See I/O grouping on page 3-21.
  • Page 46 im Vertrieb von CAMBOARD Electronics Operation, cont’d Preset button — The Preset button has two primary functions (•) and five secondary (❏) functions: • Activates Save Preset mode to save a configuration as a preset and Recall Preset mode to activate a previously-defined preset. •...
  • Page 47 im Vertrieb von CAMBOARD Electronics Esc ( ) button — The Esc ( ) button has two primary functions (•) and eight secondary (❏) functions: • Cancel operations or selections in progress and reset the front panel button indicators. The Esc ( ) button does not reset the current configuration, the RGBHV (CrossPoint 450 Plus switchers) or Video (MAV Plus switchers) button and Audio selection button, any presets, or any audio gain or attenuation or volume settings.

  • Page 48: I/O Controls

    im Vertrieb von CAMBOARD Electronics Operation, cont’d I/O controls You must specify video, audio, or both when you are creating or viewing a configuration. This is done with the RGBHV button (CrossPoint 450 Plus switchers) or Video button (MAV Plus switchers) ( ) and Audio ( ) buttons.

  • Page 49: Power Indicators (2412 And Larger Models Only)

    im Vertrieb von CAMBOARD Electronics Power indicators (2412 and larger models only) Primary and Redundant Power Supply LEDs — Green — Indicates that the associated power supply is operating within normal tolerances. Red — Indicates that the associated power supply is operating outside the normal tolerances or has failed.

  • Page 50: Creating A Configuration

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Creating a configuration The current configuration can be changed using the front panel buttons. Change the current configuration as follows: Press the Esc button to clear any input button indicators, output button indicators, or control button indicators that may be lit. Select to configure video, audio, or both by pressing the RGBHV (CrossPoint 450 Plus switchers) or Video (MAV Plus switchers) button and/or Audio button.

  • Page 51: Example 1: Creating A Set Of Video And Audio Ties

    im Vertrieb von CAMBOARD Electronics Example 1: Creating a set of video and audio ties The following steps show an example in which input 5 is tied to outputs 3, 4, and 8. The steps show the front panel indications that result from your action. This example assumes that there are no ties in the current configuration.
  • Page 52 im Vertrieb von CAMBOARD Electronics Operation, cont’d Press and release the output 3, output 4, and output 8 buttons (figure 3-8). The entire set of ties can be canceled at this point by pressing and releasing the Esc button. The Esc button flashes red once. Press and release the Output 3, Output 4, and Output 8 buttons.

  • Page 53: Example 2: Adding A Tie To A Set Of Video And Audio Ties

    im Vertrieb von CAMBOARD Electronics Example 2: Adding a tie to a set of video and audio ties The following steps show an example in which a new video tie is added to the current configuration. The steps show the front panel indications that result from your action.
  • Page 54 im Vertrieb von CAMBOARD Electronics Operation, cont’d Press and release the output 1 button (figure 3-14). Press and release the Output 1 button. The button blinks green to indicate that only the selected RGBHV C O N T R O L or video input will be tied to this output.

  • Page 55: Example 3: Removing A Tie From A Set Of Video And Audio Ties

    im Vertrieb von CAMBOARD Electronics Example 3: Removing a tie from a set of video and audio ties The following steps show an example in which an existing audio tie is removed from the current configuration. The steps show the front panel indications that result from your action.
  • Page 56 im Vertrieb von CAMBOARD Electronics Operation, cont’d Press and release the output 4 button (figure 3-20). Press and release the Output 4 button. C O N T R O L The button blinks red to indicate the pending change: audio input will be untied. VIEW ENTER PRESET...

  • Page 57: Viewing A Configuration

    im Vertrieb von CAMBOARD Electronics Viewing a configuration The current configuration can be viewed using the front panel buttons. The View- Only mode prevents inadvertent changes to the current configuration. View-Only mode also provides a way to mute video and audio outputs (see Muting and unmuting video and/or audio outputs on page 3-31.

  • Page 58: Example 4: Viewing Video And Audio, Audio Only, And Video Only Ties

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Example 4: Viewing video and audio, audio only, and video only ties The following steps show an example of viewing the video and audio, audio-only, and video-only ties in the current configuration. The steps show the front panel indications that result from your action.
  • Page 59 im Vertrieb von CAMBOARD Electronics Press and release the input 5 button (figure 3-25). The output buttons for outputs that are tied to input 5 light the appropriate color: Amber for audio and RGBHV or video ties (audio follow) Green for RGBHV or video ties (audio breakaway) Red for audio ties (audio breakaway) Press and release the Input 5 button.
  • Page 60 im Vertrieb von CAMBOARD Electronics Operation, cont’d Press and release the RGBHV (CrossPoint 450 Plus switchers) or Video (MAV Plus switchers) button and the Audio button to toggle the RGBHV or Video button on green and the Audio button either unlit or providing background illumination (figure 3-27).

  • Page 61: I/O Grouping

    im Vertrieb von CAMBOARD Electronics I/O grouping I/O grouping is a matrix switcher feature that allows you to subdivide the front panel control of the matrix into four smaller functional sub-switchers and limit tie creation from the front panel only. Inputs and outputs can be assigned to one of four groups or not assigned to any group.
  • Page 62 im Vertrieb von CAMBOARD Electronics Operation, cont’d The I/O groups can be set up on the front panel or by using RS-232/RS-422 and Ethernet ports and either the SIS or the Windows control program (see chapter 4, Programmer’s Guide, and chapter 5, Matrix Software. Create I/O groups on the front panel as follows: Press the Esc button to clear any input buttons, output buttons, or control buttons that may be lit.

  • Page 63: Example 5: Grouping Inputs And Outputs

    im Vertrieb von CAMBOARD Electronics Example 5: Grouping inputs and outputs The following steps show an example in which several switcher inputs and outputs are assigned to groups. The steps show the front panel indications that result from your action. Press and release the Esc button (figure 3-30).
  • Page 64 im Vertrieb von CAMBOARD Electronics Operation, cont’d Press and release the input 1 through 4 and output 1 through 4 buttons (figure 3-33). Press and release the Input 1 through Input 4 buttons. The selected buttons light. 17 18 19 20 21 22 23 24 Press and release the Output 1 through Input 4 buttons.

  • Page 65: Setting Rgb Delay (Crosspoint 450 Plus Switchers Only)

    im Vertrieb von CAMBOARD Electronics Do nothing for approximately 30 seconds. The front panel times out and the switcher exits I/O Group mode. • Group 1 consists of inputs 1 through 4 and outputs 1 through 4. • Group 2 consists of inputs 5 through 8 and outputs 5 through 8. Setting RGB delay (CrossPoint 450 Plus switchers only) The CrossPoint 450 Plus switchers can briefly blank the RGB (video) output while it switches to the new input’s sync source, and then switches the RGB signals.
  • Page 66 im Vertrieb von CAMBOARD Electronics Operation, cont’d Press and hold the RGBHV button for approximately 2 seconds (figure 3-37). 2 seconds RGBHV RGBHV Press and hold the RGBHV button until it blinks. = Blinking button Figure 3-37 — Select RGB Delay mode Press and release the output 17 button (figure 3-38).

  • Page 67: Using Presets

    im Vertrieb von CAMBOARD Electronics Press and release the RGBHV button (figure 3-40). Press the RGBHV button to exit RGB delay mode. I / O All input buttons and output buttons RGBHV AUDIO return to unlit or background illumination. The RGBHV button stops blinking and goes out or becomes background illuminated.

  • Page 68: Example 7: Saving A Preset

    im Vertrieb von CAMBOARD Electronics Operation, cont’d 24 x 12, 24 x 24, 32 x 16, and 32 x 32 matrix sizes Preset Preset Preset Preset Preset Preset Preset Preset Preset Preset Preset Preset Preset Preset Preset Preset 9 10 11 12 13 14 15 16 Input buttons 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32...
  • Page 69 im Vertrieb von CAMBOARD Electronics Press and hold the Preset button for approximately 2 seconds until it blinks (figure 3-43). 2 seconds (Preset Assigned) PRESET PRESET Press and hold the Preset button until it blinks. All input buttons with assigned presets light red. If you then save the configuration to a lit preset number, 17 18 17 18...

  • Page 70: Example 8: Recalling A Preset

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Example 8: Recalling a preset The following steps show an example in which a preset is recalled to become the current configuration. The steps show the front panel indications that result from your action. Press and release the Esc button (figure 3-46).

  • Page 71: Muting And Unmuting Video And/Or Audio Outputs

    im Vertrieb von CAMBOARD Electronics Press and release the Enter button (figure 3-49). The configuration stored in selected memory location is now the current configuration and can be viewed in the View-Only mode (see example 4). Press the Enter button to recall the preset.

  • Page 72: Example 9: Muting And Unmuting An Output

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Example 9: Muting and unmuting an output The following steps show an example in which several switcher outputs are muted and unmuted. The steps show the front panel indications that result from your action.
  • Page 73 im Vertrieb von CAMBOARD Electronics One at a time, press and hold the Output 3 and then the Output 4 buttons (figure 3-52) for approximately 2 seconds until the buttons begin to blink. The output 3 and output 4 video and audio signals are muted. Mute outputs one at a time.

  • Page 74: Viewing And Adjusting The Input Audio Level (Audio Models)

    im Vertrieb von CAMBOARD Electronics Operation, cont’d If both RGBHV/video and audio are selected, the unmute action toggles both the video and audio outputs. If either the video output or the audio output is already unmuted, the muted output is unmuted and the unmuted output is muted.

  • Page 75: Example 10: Viewing And Adjusting An Input Audio Level

    im Vertrieb von CAMBOARD Electronics Press and release an input button to select an input. The output buttons display audio level and polarity (+ or –) for the selected input. Each lit output button indicates 1 dB of gain or attenuation. Green output buttons indicate a gain (+) audio level and red buttons indicate an attenuation (–) level.
  • Page 76 im Vertrieb von CAMBOARD Electronics Operation, cont’d Input audio level adjustment displays CrossPoint 450 Plus / CrossPoint 450 Plus / MAV Plus MAV Plus 2412, 2424, 3216, 3232 HVA 2412, 2424, 3216, 3232 HVA 9 10 11 12 13 14 15 16 9 10 11 12 13 14 15 16 18 19 20 21 22 23 24...
  • Page 77 im Vertrieb von CAMBOARD Electronics Input audio level adjustment displays CrossPoint xi Plus / CrossPoint xi Plus / MAV Plus MAV Plus 84, 88, 124, 128 HVA 816, 168, 1616 HVA 9 10 13 14 15 16 9 10 13 14 15 16 9 10 13 14...
  • Page 78 im Vertrieb von CAMBOARD Electronics Operation, cont’d Press and hold the Audio button for approximately 2 seconds (figure 3-57). 2 seconds AUDIO AUDIO Press and hold the Audio button until it blinks. = Blinking button Figure 3-57 — Select Audio mode Press and release the input 5 button (figure 3-58).
  • Page 79 im Vertrieb von CAMBOARD Electronics Green Green Green 1 2 3 4 5 6 7 8 OUTPUTS In this example, the output buttons display an audio gain level of +8 dB. = unlit button = fast blinking button Figure 3-60 — Level display on a 8-output-button switcher Press and release the View ( ) button once (figure 3-61) to decrease the input audio level by 1 dB.

  • Page 80: Viewing And Adjusting The Output Volume (Audio Models)

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Figure 3-63 shows the same level (–1 dB) as in figure 3-61, but displayed on a 8-output-button switcher, such as a CrossPoint 450 Plus 128 HVA. 2 3 4 5 6 7 8 OUTPUTS In this example, the output buttons display an audio gain level of +8 dB.

  • Page 81: Reading The Displayed Volume

    im Vertrieb von CAMBOARD Electronics Press and release the Audio button to save the audio settings and exit the Audio mode. The Audio button stops blinking. • There is one audio volume level setting per output. The audio level setting is shared by the left and right audio inputs.
  • Page 82 im Vertrieb von CAMBOARD Electronics Operation, cont’d Audio volume adjustment settings Highest # input button lit dB of Output Highest # input button lit dB of Output 12-input 16-input 32-input attenuation volume 12-input 16-input 32-input attenuation volume switcher switcher switcher switcher switcher switcher...
  • Page 83 im Vertrieb von CAMBOARD Electronics When all input buttons are lit for any switcher model, the audio output is 100% of the audio input level. Another way to view the volume level is to think in terms of the attenuation that is applied to the output.

  • Page 84: Example 11: Viewing And Adjusting An Output Volume Level

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Example 11: Viewing and adjusting an output volume level The following steps show an example in which the audio output volume is viewed and adjusted. The steps show the front panel indications that result from your action.
  • Page 85 im Vertrieb von CAMBOARD Electronics Figure 3-68 shows the same volume (41.5%) as in figure 3-67, but displayed on a 12-ouput-button switcher, such as a CrossPoint 450 Plus 128 HVA. The input LEDs display the selected output's audio volume level. In this example, the lit/blinking input buttons indicate 40 to 41.5 percent of the applied audio input.
  • Page 86 im Vertrieb von CAMBOARD Electronics Operation, cont’d Press and release the Esc ( ) button once (figure 3-70) to increase the volume by 1.5%. Press and release the Esc ( ) button several more times (figure 3-70) to increase the volume by 1.5% per button push. Note the input button indication changes that occur each time the Esc ( ) button is pressed and released.

  • Page 87: Locking Out The Front Panel (Executive Mode)

    im Vertrieb von CAMBOARD Electronics Figure 3-72 shows the same volume (61%) as in figure 3-70, but displayed on a 16-ouput-button switcher, such as a CrossPoint 1616 HVA. The input LEDs display the selected output's audio volume level. In this example, the lit/blinking input buttons indicate 59.5 to 62.5 percent of the applied audio input. The unlit/blinking input buttons indicate an audio volume attenuation of 25 dB to 27 dB.

  • Page 88: Performing A System Reset From The Front Panel

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Performing a system reset from the front panel The front panel reset is identical to the ZXXX SIS command (see chapter 4, Programmer’s Guide). A system reset clears all ties and presets, all video and audio mutes, resets all I/O grouping, sets all input audio levels to unity gain (+0 dB), and sets all output volume levels to 100% (0 dB of attenuation).

  • Page 89: Selecting The Rs-232/Rs-422 Protocol And Baud Rate

    im Vertrieb von CAMBOARD Electronics Selecting the RS-232/RS-422 protocol and baud rate The switcher can support either RS-232 or RS-422 serial communication protocol, and operate at 9600, 19200, 38400, and 115200 baud rates. The settings of these variables can be viewed and changed from the front panel. View and configure the switcher ’s serial communications settings as follows: To enter Serial Port Configuration mode, simultaneously press and hold all Control buttons (Enter, Preset, View, and Esc) (figure 3-77).

  • Page 90: Rear Panel Controls

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Rear Panel Controls The rear panel has a Reset button that initiates four levels of matrix switcher resets. Press and hold the button while the switcher is running or while you apply power to the switcher for different reset levels.
  • Page 91 im Vertrieb von CAMBOARD Electronics Perform a soft reset of the switcher as follows: Press and hold the Reset button until the front panel RGBHV (CrossPoint 450 Plus)/Video (MAV Plus) and Audio buttons blink once (events reset), twice (system reset), or three times (absolute reset) (figure 3-80). Release, then immediately Press and hold...

  • Page 92: Performing A Hard Reset

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Performing a hard reset The hard reset function restores the switcher to the base firmware that it shipped with. After a hard reset, events do not automatically start, but user settings and files are restored. Perform a hard reset as follows: The hard reset restores the factory-installed firmware.

  • Page 93: Troubleshooting

    im Vertrieb von CAMBOARD Electronics Troubleshooting This section gives recommendations on what to do if you have problems operating the CrossPoint 450 Plus or MAV Plus switcher, and it describes an actual image problem that Extron has encountered. General checks Ensure that all devices are plugged in and powered on.

  • Page 94: Configuration Worksheets

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Configuration Worksheets Rather than trying to remember the configuration for each preset, use worksheets to record this information. Make copies of the blank worksheet on page 3-57 (32-input button and -output button switchers) and page 3-59 (16-button switchers) and use one for each preset configuration.

  • Page 95: Worksheet Example 2: Daily Configuration

    im Vertrieb von CAMBOARD Electronics Worksheet example 2: Daily configuration Figure 3-83 continues from worksheet example 1 by showing the video and audio ties that make up the configuration of preset 1. A solid ink line shows video ties and a dashed pencil line shows the audio ties. In this example: •...

  • Page 96: Worksheet Example 3: Test Configuration

    im Vertrieb von CAMBOARD Electronics Operation, cont’d Worksheet example 3: Test configuration The A/V system in our fictional organization needs to be fine tuned on a regular basis. Figure 3-84 shows a typical test configuration, with an Extron video test generator (input 12) generating a test pattern to all monitors (outputs 1, 2, 3, 4, 8, 9, 10, and 12).
  • Page 97 im Vertrieb von CAMBOARD Electronics www.camboard.de Tel. 07131 911201 ce-info@camboard.de CrossPoint 450 Plus and MAV Plus Switchers • Operation 3-57 Fax 07131 911203...
  • Page 98 im Vertrieb von CAMBOARD Electronics Operation, cont’d This page was intentionally left blank. www.camboard.de Tel. 07131 911201 ce-info@camboard.de 3-58 CrossPoint 450 Plus and MAV Plus Switchers • Operation Fax 07131 911203...
  • Page 99 im Vertrieb von CAMBOARD Electronics www.camboard.de Tel. 07131 911201 ce-info@camboard.de CrossPoint 450 Plus and MAV Plus Switchers • Operation 3-59 Fax 07131 911203...
  • Page 100 im Vertrieb von CAMBOARD Electronics Operation, cont’d This page was intentionally left blank. www.camboard.de Tel. 07131 911201 ce-info@camboard.de 3-60 CrossPoint 450 Plus and MAV Plus Switchers • Operation Fax 07131 911203...

  • Page 101: Chapter 4 • Programmer's Guide

    im Vertrieb von CAMBOARD Electronics CrossPoint 450 Plus and MAV Plus Switchers Chapter Four Programmer’s Guide RS-232/RS-422 Link Ethernet Link Host-to-Switcher Instructions Switcher-Initiated Messages Switcher Error Responses Using the Command/Response Tables Command/Response Table for SIS Commands Command Response Table for IP SIS Commands Special Characters www.camboard.de Tel.

  • Page 102: Rs-232/Rs-422 Link

    im Vertrieb von CAMBOARD Electronics Programmer’s Guide Programmer’s Guide, cont’d RS-232/RS-422 Link The switcher’s rear panel Remote 9-pin D female connector (figure 4-1) can be connected to the RS-232 or RS-422 serial port output of a host device such as a computer running the HyperTerminal utility, an RS-232 capable PDA, or a control system.

  • Page 103: Ethernet Link

    im Vertrieb von CAMBOARD Electronics Ethernet Link The rear panel Ethernet connector on the switcher can be connected to an Ethernet LAN or WAN. This connection makes SIS control of the switcher possible using a computer connected to the same LAN or WAN. Ethernet connection The Ethernet cable can be terminated as a straight-through cable or a crossover cable and must be properly terminated for your application (figure 4-2).

  • Page 104: Host-To-Switcher Instructions

    The switcher-initiated messages are listed below (underlined). (C) Copyright 2004, Extron Electronics CP 300 450 MAV IP, Vx.xx The switcher initiates the copyright message when it is first powered on or when connection via Internet protocol (IP) is established. Vx.xx is the firmware version number.

  • Page 105: Switcher Error Responses

    im Vertrieb von CAMBOARD Electronics Amtnn•x The switcher initiates the Amt message when an audio output mute is toggled on or off from the front panel. “nn” is the output number, • is a space, and “x” is the mute status: 1 = on, 0 = off. Exen The switcher initiates the Exe message when executive mode is toggled on or off from the front panel.

  • Page 106: Command/Response Table For Sis Commands

    im Vertrieb von CAMBOARD Electronics Programmer’s Guide, cont’d Command/Response Table for SIS Commands Symbol Definitions: = Carriage return/line feed = Carriage return (no line feed) • = Space = Escape key Input and output numbers in commands may be entered as either 1-digit, 2-digit, or 3-digit numbers.
  • Page 107 im Vertrieb von CAMBOARD Electronics Command/response table for SIS commands Command ASCII Command Response Additional description (host to switcher) (switcher to host) Create ties • Commands can be made back-to-back, with no spaces. For example: 1*1!02*02&003*003%4*24$. • The quick multiple tie and tie input to all output commands activate all I/O switches simultaneously.
  • Page 108 im Vertrieb von CAMBOARD Electronics Programmer’s Guide, cont’d Command/response table for SIS commands (Cont’d) Command ASCII Command Response Additional description (host to switcher) (switcher to host) Video mute commands RGB mute Mute output RGB (video off). RGB unmute Unmute output RGB (video on).
  • Page 109 im Vertrieb von CAMBOARD Electronics Audio volume adjustment settings dB of Output dB of Output dB of Output value value value attenuation volume attenuation volume attenuation volume 5.5% 38.5% 71.5% 8.5% 41.5% 74.5% 11.5% 44.5% 77.5% 14.5% 47.5% 80.5% 17.5% 50.5% 83.5% 20.5%...
  • Page 110 im Vertrieb von CAMBOARD Electronics Programmer’s Guide, cont’d Command/response table for SIS commands (Cont’d) Command ASCII Command Response Additional description (host to switcher) (switcher to host) Names Write global preset name Esc X11 Example: 1,Security 1NG Nmg01,Security 1 Name global preset 1 “Security 1”. Read global preset name Esc X11 Example:...
  • Page 111 im Vertrieb von CAMBOARD Electronics Command/response table for SIS commands (Cont’d) Command ASCII Command Response Additional description (host to switcher) (switcher to host) I/O Grouping (Continued) Read output grouping … entry for each output, starting from input 1, n is the maximum number of inputs for this model.
  • Page 112 im Vertrieb von CAMBOARD Electronics Programmer’s Guide, cont’d Command/response table for SIS commands (Cont’d) Command ASCII Command Response Additional description (host to switcher) (switcher to host) Save, recall, and directly write presets (continued) Read room outputs Esc X8 Example: Class 1,01,02,08,09 Outputs 1, 2, 8, and 9 are assigned to room 3, which is named “Class 1”.
  • Page 113 im Vertrieb von CAMBOARD Electronics Command/response table for SIS commands (Cont’d) Command ASCII Command Response Additional description (host to switcher) (switcher to host) View ties, gain, volume, mutes, presets, and DSVP View RGBHV output tie & Example: 15& Input 27 RGBHV tied to output View video output tie Example: Input 2 video tied to output 7.
  • Page 114 im Vertrieb von CAMBOARD Electronics Programmer’s Guide, cont’d Command/response table for SIS commands (Cont’d) Command ASCII Command Response Additional description (host to switcher) (switcher to host) View ties, gain, volume, mutes, presets, and DSVP (continued) View audio global preset configuration *2VC •...
  • Page 115 im Vertrieb von CAMBOARD Electronics Command/response table for SIS commands (Cont’d) Command ASCII Command Response Additional description (host to switcher) (switcher to host) Information requests Information request •A = V size, A = A Size. Example: V32X16•A32X16 32 video and 32 audio inputs by 16 video and 16 audio outputs (CrossPoint 450 Plus 3216 HVA).

  • Page 116: Command/Response Table For Ip Sis Commands

    im Vertrieb von CAMBOARD Electronics Programmer’s Guide, cont’d Command/Response Table for IP SIS Commands Symbol Definitions: = Matrix name (Up to 240 characters) The following characters are invalid in the name: {space} ~ , @ = , ‘ [ ] { } < > ’ “ ; : | \ and ?. = Default name Factory default name (model name + last 3 pairs of MAC address).
  • Page 117 im Vertrieb von CAMBOARD Electronics = Data bits 7, 8 = Stop bits 1, 2 = Port type 0 = RS-232, 1 = RS-422, 2 = RS-485 = Verbose mode 0 = Clear/none (default for Telnet connection) 1 = Verbose mode (default for RS-232/RS-422 connection) 2 = Tagged responses for queries 3 = Verbose mode and tagged for queries If tagged responses is enabled, all read commands return the constant string and the value as the...

  • Page 118: Special Characters

    im Vertrieb von CAMBOARD Electronics Programmer’s Guide, cont’d Command/response table for IP SIS commands (continued) Command ASCII Command Response Additional description (host to switcher) (switcher to host) IP setup commands (continued) , ..., You must first have set an e-mail Set e-mail events for recipient Esc X41 recipient for the e-mail account...

  • Page 119: Chapter 5 • Matrix Software

    im Vertrieb von CAMBOARD Electronics CrossPoint 450 Plus and MAV Plus Switchers Chapter Five Matrix Software Matrix Switchers Control Program Special Characters Button-Label Generator www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...

  • Page 120: Matrix Switchers Control Program

    By default, the Windows installation creates a C:\MTRX50 directory and places two icons (MATRIX Switcher+ Control Program and MATRIX Switcher+ Help) into a group or folder named “Extron Electronics”. The program was designed to control most Extron matrix switchers, but its operation is limited to the features and configuration of your CrossPoint 450 Plus or MAV Plus switcher.

  • Page 121: Using The Software

    To run the Matrix Switcher+ Control Program, double-click on the Matrix Switcher+ Control Program icon (shown at right) in the Extron Electronics group or folder. The Comm Port Selection window (figure 5-1) appears. Figure 5-1 — Comm port selection window Choose either the comm port that is connected to the CrossPoint 450 Plus or MAV Plus switcher’s RS-232/RS-422 port, IP [LAN], or Emulate.
  • Page 122 im Vertrieb von CAMBOARD Electronics Matrix Software, cont’d If you selected IP [LAN] in step 2, the IP Connection window appears (figure 5-2). Figure 5-2 — Address and password entry Examine the Extron IP Address field in the IP Connection window. The field displays the last Extron IP address entered.
  • Page 123 im Vertrieb von CAMBOARD Electronics The Extron Matrix Switcher+ Control Program window (figure 5-3 and figure 5-4) appears. The window displays the current configuration of the attached matrix. Figure 5-3 — Extron Matrix Switcher+ Control Program window (blank) Figure 5-4 — Sample program window (complete) www.camboard.de Tel.

  • Page 124: Ip Settings/Options Window

    im Vertrieb von CAMBOARD Electronics Matrix Software, cont’d • To set up audio in follow mode (audio and video have the same tie configuration), select the Follow box at the bottom of the window. To set up audio in breakaway mode (audio and video have different tie configurations), deselect the Follow box.

  • Page 125: Matrix Ip Address Field

    im Vertrieb von CAMBOARD Electronics Editing variables on the IP Settings/Options screen while connected via the Ethernet port can immediately disconnect the user from the switcher. Extron recommends editing the settings on this screen using the RS-232 link and protecting the Ethernet access to this screen by assigning an administrator’s password to qualified and knowledgeable personnel only.

  • Page 126: Gateway Ip Address Field

    im Vertrieb von CAMBOARD Electronics Matrix Software, cont’d Gateway IP address field The Gateway IP Address field identifies the address of the gateway to the mail server to be used if the CrossPoint 450 Plus or MAV Plus switcher and the mail server are not on the same subnet.

  • Page 127: Time (Local) Field

    im Vertrieb von CAMBOARD Electronics Time (local) field The Time (local) field displays the current time in the local time zone. If necessary, click on the Sync Time to PC button to set the switcher to your computer’s internal time or else adjust the time manually as follows: Click in the time field.

  • Page 128: User Password Field

    im Vertrieb von CAMBOARD Electronics Matrix Software, cont’d The following characters are invalid in passwords: {space} + ~ , @ = ‘ [ ] { } < > ’ “ ; : | \ and ?. Edit this field as follows: Click in the Administrator Password field.

  • Page 129: Mail Server Domain Name Field

    im Vertrieb von CAMBOARD Electronics Mail Server Domain Name field The Mail Server Domain Name field displays the domain name that the CrossPoint 450 Plus or MAV Plus switcher uses to log on to the e-mail server. Standard domain conventions (such as nnnnn@xxx.com) apply. The following characters are invalid in a domain name: {space} + ~ , = ‘...

  • Page 130: Update Firmware

    im Vertrieb von CAMBOARD Electronics Matrix Software, cont’d The radio buttons and check boxes associated with each address field permit the administrator to specify specific e-mail requirements for each recipient. Edit these fields and controls as follows: Click in the desired E-mail Addressee field. The graphic cursor becomes a text cursor.
  • Page 131 im Vertrieb von CAMBOARD Electronics Click Tools > Update firmware. The open file window appears (figure 5-7). Figure 5-7 — Open window Navigate to the folder where you saved the firmware upgrade file. Select the file. Valid firmware files must have the file extension .S19. Any other file extension is not a firmware upgrade.

  • Page 132: Upload Html Files

    im Vertrieb von CAMBOARD Electronics Matrix Software, cont’d Upload HTML files You can create customized HTML pages for the switcher to display. The HTML Files List window (figure 5-8) provides a way to view the contents of the switcher’s file system and upload custom HTML pages to the switcher. Figure 5-8 —...

  • Page 133: Windows Buttons, Drop Boxes, And Trash

    im Vertrieb von CAMBOARD Electronics Windows buttons, drop boxes, and trash The buttons, drop boxes, and trash can on the right side of the program window perform the following functions: Power — Unavailable for CrossPoint 450 Plus and MAV Plus switchers, because the switcher power cannot be controlled via software.

  • Page 134: Tools Menu

    im Vertrieb von CAMBOARD Electronics Matrix Software, cont’d Tools menu Assign device icons — Displays the complete set of input and output device icons. You can drag any of these icons to the input and output boxes. Edit device palette — Allows you to add your own device icon graphics.

  • Page 135: Preferences Menu

    im Vertrieb von CAMBOARD Electronics Green — Proper operation. Red — Component has failed. White — Components are not installed. The CrossPoint 450 Plus and MAV Plus switchers are not available in custom configurations. Each model has all available monitored components, such as power supplies and fans, installed.
  • Page 136 im Vertrieb von CAMBOARD Electronics Matrix Software, cont’d Ties as crosspoints — Displays ties as a matrix of inputs and outputs (figure 5-11). Ties that have been made are indicated as amber (video and audio), green (video only), and red (audio only) boxes. Ties that will take effect when you click on the Take button are indicated by +.

  • Page 137: Master Reset Selection

    Using the help system For information about program features, you can access the help program in any of the following ways: • From the Extron Electronics program folder or group, double-click on the MATRIX Switcher+ Help icon (shown at right). •...

  • Page 138: Button Label Generator

    Matrix Switcher+ Control Program, or the C:\BUTTONS directory, if installed as a stand-alone program. The Button-Label Generator icon is placed in the “Extron Electronics” group or folder. Using the software To run the Button-Label Generator program, double-click on the Button-Label Generator icon (shown at right) in the Extron Electronics group or folder, and click OK when prompted.

  • Page 139: Chapter 6 • Html Operation

    im Vertrieb von CAMBOARD Electronics CrossPoint 450 Plus and MAV Plus Switchers Chapter Six HTML Operation Download the Startup Page System Status Page System Configuration Page File Management Page Set and View Ties Page Special Characters www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...

  • Page 140: Download The Startup Page

    im Vertrieb von CAMBOARD Electronics HTML Operation HTML Operation, cont’d The switcher can be controlled and operated through its Ethernet port, connected via a LAN or WAN, using a web browser such as Microsoft’s Internet Explorer. The browser’s display of the switcher’s status or operation has the appearance of web pages.

  • Page 141: System Status Page

    im Vertrieb von CAMBOARD Electronics Is there a file in the switcher’s memory that is named “index.html”? If so, the switcher downloads “index.html” as the default startup page. If neither of the above conditions is true, the switcher downloads the factory-installed default startup page, “nortxe_index.html”...

  • Page 142: Dsvp Page (Crosspoint 450 Plus Switchers Only)

    im Vertrieb von CAMBOARD Electronics HTML Operation, cont’d DSVP page (CrossPoint 450 Plus switchers only) You can view a snapshot-in-time of the input frequencies of connected inputs on the Digital Sync Validation Processing (DSVP) page (figure 6-3). Click the DSVP link to the left of the Status page to download the DSVP page.

  • Page 143: System Configuration Page

    im Vertrieb von CAMBOARD Electronics System Configuration Page The CrossPoint 450 Plus or MAV Plus switcher downloads the System Configuration page (figure 6-4) when you click the Configuration tab. The screen consists of fields in which you can view and edit IP administration and system settings.

  • Page 144: Ip Settings Fields

    im Vertrieb von CAMBOARD Electronics HTML Operation, cont’d IP Settings fields The IP Settings fields provide a location for viewing and editing settings unique to the Ethernet interface. After editing any of the settings on this page, click the Submit button at the bottom of the page. Unit Name field The Unit Name field contains the name used as the “from”...

  • Page 145: Date/Time Settings Fields

    im Vertrieb von CAMBOARD Electronics Date/Time Settings fields The Date/Time Settings fields (figure 6-5) provide a location for viewing and setting the time functions. Figure 6-5 — Date/Time Settings fields Change the date and time settings as follows: Click the desired variable’s drop box. The adjustable variables are month, day, year, hours, minutes, AM/PM, and (time) zone.

  • Page 146: Passwords Page

    im Vertrieb von CAMBOARD Electronics HTML Operation, cont’d Passwords page Access the Passwords page (figure 6-6) by clicking the Passwords link on the System Settings page. Select System Settings. Select Email Settings. Select Firmware Upgrade. Figure 6-6 — Passwords page The fields on the Passwords page are for entering and verifying administrator and user passwords.

  • Page 147: Email Settings Page

    im Vertrieb von CAMBOARD Electronics Email Settings page Reach the Email Settings page (figure 6-7) by clicking the Email Settings link on the System Configuration page. The Email Settings page has fields for setting up the switcher’s e-mail notification capabilities. For the e-mail settings and for each row of the e-mail notification settings, click the Edit button to make the fields available for editing.

  • Page 148: Email Address Fields

    im Vertrieb von CAMBOARD Electronics HTML Operation, cont’d Email address fields The eight Email address fields identify the e-mail addresses of the personnel to whom the CrossPoint 450 Plus or MAV Plus switcher e-mails notification of its failure and repair status. Standard e-mail address conventions (nnnnn@xxx.com) apply.

  • Page 149: File Management Page

    im Vertrieb von CAMBOARD Electronics Connect the PC to the CrossPoint 450 Plus or MAV Plus switcher via the switcher’s Ethernet port. Access the CrossPoint 450 Plus or MAV Plus switcher using HTML pages. Click the Configuration tab. Click the Firmware Upgrade link. Click the Browse button.

  • Page 150: Set And View Ties Page

    im Vertrieb von CAMBOARD Electronics HTML Operation, cont’d Upload your own files as follows: The following characters are invalid in file names: {space} + ~ , @ = ‘ [ ] { } < > ’ “ ; : | \ and ?. Click the Browse button.

  • Page 151: Create A Tie

    im Vertrieb von CAMBOARD Electronics Create a tie Select and switch an input as follows: Click the Video Only, Audio Only, or Video & Audio button to select video, audio, or both for switching (audio follow or audio breakaway). Each mouse click on a button toggles the other two buttons off.
  • Page 152 im Vertrieb von CAMBOARD Electronics HTML Operation, cont’d Change the input gain and attenuation (audio models only) Users can set each input’s level of audio gain or attenuation (-18 dB to +24 dB) from the RGB and Audio Settings page. Audio levels can be adjusted so there are no noticeable volume differences between sources.
  • Page 153 im Vertrieb von CAMBOARD Electronics Mute and unmute one or all outputs Mute one or all outputs as follows: To select an individual output to mute or unmute, click the Output drop box. A drop down scroll box appears (figure 6-14). Figure 6-14 —...

  • Page 154: Change The Rgb Delay (Crosspoint 450 Plus Switchers Only)

    im Vertrieb von CAMBOARD Electronics HTML Operation, cont’d Change the RGB delay (CrossPoint 450 Plus switchers only) The RGB delay interval defines how long the screen is blanked when switching to a new input for the selected output. Change the RGB delay as follows: Click the Output drop box.

  • Page 155: Change The Output Volume Level (Audio Models Only)

    im Vertrieb von CAMBOARD Electronics Change the output volume level (audio models only) Users can set each output’s volume level through a range of zero steps of attenuation (full attenuation, minimum volume) to 64 steps of attenuation (no attenuation, full volume) from the RGB and Audio Settings page. Change an output’s audio level setting as follows: Click the output drop box.
  • Page 156 im Vertrieb von CAMBOARD Electronics HTML Operation, cont’d Audio volume adjustment settings dB of Output dB of Output dB of Output value value value attenuation volume attenuation volume attenuation volume 5.5% 38.5% 71.5% 8.5% 41.5% 74.5% 11.5% 44.5% 77.5% 14.5% 47.5% 80.5% 17.5%...

  • Page 157: Global Presets Page

    im Vertrieb von CAMBOARD Electronics Global Presets page You can save and recall global presets from the Global presets page (figure 6-20). Access the Global presets page by clicking the Global Presets link on the left of the Control page. Select Set &...

  • Page 158: Special Characters

    im Vertrieb von CAMBOARD Electronics HTML Operation, cont’d Special Characters The HTML language reserves certain characters for specific functions. The switcher will not accept these characters as part of preset names, the switcher’s name, passwords, or locally created file names. The switcher rejects the following characters: {space} + ~ , @ = ‘...

  • Page 159: Appendix A • Ethernet Connection

    im Vertrieb von CAMBOARD Electronics CrossPoint 450 Plus and MAV Plus Switchers A ppendix A Ethernet Connection Ethernet Link Subnetting — A Primer www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...

  • Page 160: Ethernet Connection

    im Vertrieb von CAMBOARD Electronics Ethernet Connection, cont’d Ethernet Link The rear panel Ethernet connector on the CrossPoint 450 Plus or MAV Plus switcher can be connected to an Ethernet LAN or WAN. This connection makes SIS control of the switcher possible using a computer connected to the same LAN.

  • Page 161: Ping To Determine Extron Ip Address

    im Vertrieb von CAMBOARD Electronics Ping to determine Extron IP address The Microsoft Ping utility is available at the DOS prompt. Ping tests the Ethernet interface between the computer and the CrossPoint 450 Plus or MAV Plus switcher. Ping can also be used to determine the actual numeric IP address from an alias and to determine the web address.

  • Page 162: Telnet Tips

    im Vertrieb von CAMBOARD Electronics Ethernet Connection, cont’d Microsoft (R) windows 2000 (TM) Version 5.0 (Build 2195) Welcome to Microsoft Telnet Client Telnet Client Build 5.00.99203.1 Escape Character is 'CTRL+]' Microsoft Telnet> Figure A-3 — Telnet screen Telnet tips It is not the intention of this manual to detail all of the operations and functionality of Telnet, however some basic level of understanding is necessary for operating the CrossPoint 450 Plus or MAV Plus switcher via Telnet.

  • Page 163: Local Echo

    im Vertrieb von CAMBOARD Electronics Local echo Once connected to the CrossPoint 450 Plus or MAV Plus switcher, by default, Telnet does not display your keystrokes on the screen. SIS commands are typed in blindly and only the SIS responses are displayed on the screen. To command Telnet to show keystrokes, at the Telnet prompt, type set local_echo and then press [Enter] before you open the connection to the switcher.

  • Page 164: Subnetting - A Primer

    im Vertrieb von CAMBOARD Electronics Ethernet Connection, cont’d Subnetting — A Primer It is not the purpose of this manual to describe TCP/IP protocol in detail. However, some understanding of TCP/IP subnetting (a subnet is a subset of a network — a set of IP devices that have portions of their IP addresses in common) is necessary in order to understand the interaction of the CrossPoint 450 Plus or MAV Plus switcher and the mail server gateway.

  • Page 165: Determining Whether Devices Are On The Same Subnet

    im Vertrieb von CAMBOARD Electronics Determining whether devices are on the same subnet To determine the subnet, the local device’s IP address is compared to the remote device’s IP address (figure A-6). Each address’s octets are compared or not compared, depending on the value in the related subnet mask octet. •...
  • Page 166 im Vertrieb von CAMBOARD Electronics Ethernet Connection, cont’d This page was intentionally left blank. www.camboard.de Tel. 07131 911201 ce-info@camboard.de CrossPoint 450 Plus and MAV Plus Switchers • Ethernet Connection Fax 07131 911203...

  • Page 167: Appendix B • Reference Information

    im Vertrieb von CAMBOARD Electronics CrossPoint 450 Plus and MAV Plus Switchers A ppendix B Reference Information CrossPoint 450 Plus Specifications MAV Plus Specifications Part Numbers Button Labels www.camboard.de Tel. 07131 911201 ce-info@camboard.de Fax 07131 911203...

  • Page 168: Crosspoint 450 Plus Specifications

    im Vertrieb von CAMBOARD Electronics Reference Information Reference Information, cont’d CrossPoint 450 Plus Specifications Video Routing .......... 84 Series ....8 x 4 matrix 88 Series ....8 x 8 matrix 124 Series ....12 x 4 matrix 128 Series ....12 x 8 matrix 816 Series ....
  • Page 169 im Vertrieb von CAMBOARD Electronics Sync Input type ........RGBHV, RGBS, RGsB, RsGsBs Output type ........RGBHV, RGBS, RGsB, RsGsBs Input level ........0.5 V to 5.0 V p-p, 4.0 V p-p normal Output level ........AGC to TTL: 4 V to 5 V p-p, unterminated Input impedance 84/88/124/128/816/168/1616 Series ..
  • Page 170 im Vertrieb von CAMBOARD Electronics Reference Information, cont’d Audio output — HVA models only Number/signal type ....4, 8, 12, 16, 24, or 32 stereo, balanced/unbalanced Connectors ........(4, 8, 12, 16, 24, or 32) 3.5 mm captive screw connectors, 5 pole Impedance ........
  • Page 171 im Vertrieb von CAMBOARD Electronics Product weight 84/88/124/128 Series ..14.4 lbs (6.5 kg) 816/168/1616 Series ... 19.4 lbs (8.8 kg) 2412/3216 Series ....32 lbs (14.5 kg) 2424/3232 Series ....36 lbs (14.5 kg) Shipping weight 84/88/124/128 Series ..21 lbs (9.5 kg) DIM weight ......

  • Page 172: Mav Plus Specifications

    im Vertrieb von CAMBOARD Electronics Reference Information, cont’d MAV Plus Specifications Video — video models Routing .......... MAV Plus 88 Series: 8 x 8 matrix MAV Plus 816 Series: 8 x 16 matrix MAV Plus 128 Series: 12 x 8 matrix MAV Plus 168 Series: 16 x 8 matrix MAV Plus 1616 Series: 16 x 16 matrix MAV Plus 2412 Series: 24 x 12 matrix...
  • Page 173 im Vertrieb von CAMBOARD Electronics Video output — video models Number/signal type MAV Plus 2412/2424/3216/3232 Series 12, 16, 24, or 32 composite video All other models ....4, 8, or 16 RGsB, RsGsBs, HDTV, component video, S-video, composite video (follows input type) Connectors MAV Plus 88/128/168 Series 8 x 3 BNC female for RGB/HDTV/component video, 8 x 2 BNC female for...
  • Page 174 im Vertrieb von CAMBOARD Electronics Reference Information, cont’d Gain MAV Plus 128 RCA .... Unbalanced 0 dB All other models ....Unbalanced output: -6 dB; balanced output: 0 dB Frequency response ..... 20 Hz to 20 kHz, ±0.05 dB THD + Noise ........ 0.03% @ 1 kHz at nominal level S/N ..........
  • Page 175 im Vertrieb von CAMBOARD Electronics ® Program control ......Extron’s control/configuration program for Windows Extron’s Simple Instruction Set (SIS ™ ® ® ® Microsoft Internet Explorer, Netscape Navigator , Telnet General Power ..........100 VAC to 240 VAC, 50/60 Hz, internal, autoswitchable MAV Plus 88/128 Series: 30 watts MAV Plus 816/168/1616 Series: 48 watts MAV Plus 2412/2424 Series: 2 (primary and redundant), 100 watts...

  • Page 176: Part Numbers

    Vertrieb von CAMBOARD Electronics Reference Information, cont’d Part Numbers CrossPoint 450 Plus part numbers Model Part # CrossPoint 450 Plus 84 HV 60-337-12 CrossPoint 450 Plus 84 HVA 60-337-11 CrossPoint 450 Plus 88 HV 60-336-12 CrossPoint 450 Plus 88 HVA...
  • Page 177 im Vertrieb von CAMBOARD Electronics Model (continued) Part # MAV Plus 124 HD component/HDTV video 60-658JZ MAV Plus 124 HDA component/HDTV video and audio 60-658JW MAV Plus 124 SV S-video 60-658IZ MAV Plus 124 SVA S-video and audio 60-658IW MAV Plus 124 V composite video 60-658HZ MAV Plus 124 AV composite video and audio 60-658HW...

  • Page 178: Included Parts

    im Vertrieb von CAMBOARD Electronics Reference Information, cont’d Model (continued) Part # MAV Plus 3232 SV S-video 60-473-22 MAV Plus 3232 SVA S-video and audio 60-473-21 MAV Plus 3232 V composite video 60-473-02 MAV Plus 3232 AV composite video and audio 60-473-01 MAV Plus 3232 A audio 60-473-03...

  • Page 179: Assorted Connectors

    im Vertrieb von CAMBOARD Electronics Plenum BNC-5 Mini HR Cable Part # Plenum BNC-5 Mini HR bulk, 500’ 22-103-02 Plenum BNC-5 Mini HR bulk, 1000’ 22-103-03 Assorted connectors BNC connectors Part # BNC Mini HR crimp connectors, qty. 50 100-074-51 SHRmale crimp connectors, qty.

  • Page 180: Button Labels

    im Vertrieb von CAMBOARD Electronics Reference Information, cont’d Button Labels Page B-15 provides strips of blank button labels. If desired, photocopy them or cut them out of the manual, write button information in each button area as desired, and put them in the switcher’s input or output buttons’ windows. You can also create labels using the Button-Label Generator software (see chapter 5, Matrix Software).
  • Page 181 im Vertrieb von CAMBOARD Electronics www.camboard.de Tel. 07131 911201 ce-info@camboard.de CrossPoint 450 Plus and MAV Plus Switchers • Reference Information B-15 Fax 07131 911203...
  • Page 182 im Vertrieb von CAMBOARD Electronics Reference Information, cont’d www.camboard.de Tel. 07131 911201 ce-info@camboard.de B-16 CrossPoint 450 Plus and MAV Plus Switchers • Reference Information Fax 07131 911203...
  • Page 183 Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period...
  • Page 184 PM Industrial Building 16 Ichibancho The Netherlands Singapore 368363 Chiyoda-ku, Tokyo 102-0082 Japan 714.491.1500 +31.33.453.4040 +65.6383.4400 +81.3.3511.7655 www.extron.com Fax 714.491.1517 Fax +31.33.453.4050 Fax +65.6383.4664 Fax +81.3.3511.7656 www.camboard.de Tel. 07131 911201 ce-info@camboard.de © 2004 Extron Electronics. All rights reserved. Fax 07131 911203...

This manual is also suitable for:

Crosspoint 450 plus seriesMav plus seriesCrosspoint 450 plus 124 hvCrosspoint 450 plus 88 hvaCrosspoint 450 plus 128 hvCrosspoint 450 plus 128 hva ... Show all

Table of Contents