Extron electronics CrossPoint 450 Plus Series Setup Manual
  1. Manuals
  2. Brands
  3. Extron electronics Manuals
  4. Matrix Switcher
  5. CrossPoint 450 Plus 64 Series
  6. Setup manual
Extron electronics CrossPoint 450 Plus Series Setup Manual

Extron electronics CrossPoint 450 Plus Series Setup Manual

Hide thumbs Also See for CrossPoint 450 Plus Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Enlarged version
Extron Electronics, USA
Extron Electronics, Europe
1230 South Lewis Street
Beeldschermweg 6C
Anaheim, CA 92805
3821 AH Amersfoort, The Netherlands
800.633.9876 714.491.1500
+800.3987.6673 +31.33.453.4040
FAX 714.491.1517
FAX +31.33.453.4050
www.extron.com
© 2008 Extron Electronics. All rights reserved.
Extron Electronics, Asia
Extron Electronics, Japan
135 Joo Seng Rd. #04-01
Kyodo Building, 16 Ichibancho
PM Industrial Bldg., Singapore 368363
Chiyoda-ku, Tokyo 102-0082
+800.7339.8766 +65.6383.4400
Japan
FAX +65.6383.4664
+81.3.3511.7655 FAX +81.3.3511.7656
Set Up Guide
CrossPoint 450 Plus Series
CrossPoint Ultra Series
MAV Plus Series
Matrix Switchers
68-521-50 Rev. A
05 08

Advertisement

Table of Contents
loading

Related Manuals for Extron electronics CrossPoint 450 Plus Series

Summary of Contents for Extron electronics CrossPoint 450 Plus Series

  • Page 1 Anaheim, CA 92805 3821 AH Amersfoort, The Netherlands PM Industrial Bldg., Singapore 368363 Chiyoda-ku, Tokyo 102-0082 05 08 800.633.9876 714.491.1500 +800.3987.6673 +31.33.453.4040 +800.7339.8766 +65.6383.4400 Japan FAX 714.491.1517 FAX +31.33.453.4050 FAX +65.6383.4664 +81.3.3511.7655 FAX +81.3.3511.7656 www.extron.com © 2008 Extron Electronics. All rights reserved.
  • Page 2 Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, elektrischen Schlags und/oder andere Gefahren bestehen. use. In no event will Extron Electronics be liable for direct, indirect, or consequential sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, und verstehen.
  • Page 3 安全须知 • 中文 警告 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 这个符号提示用户该设备用户手册中 必 须 使 用 有 地 线 的 供 电 系 统 供 电 。 第 三 条 线 有重要的操作和维护说明。...

  • Page 4: Table Of Contents

    Table of Contents Chapter One • Introduction ............ 1-1 About this Manual ..............1-2 About the Matrix Switchers ........... 1-2 Chapter Two • Installation ............2-1 Rear Panel ..................2-2 Making connections and rear panel settings ....... 2-4 Front Panel Configuration Port (Matrix Sizes up to 1616) ............

  • Page 5: Chapter One • Introduction

    Table of Contents, cont’d CrossPoint / MAV Matrix Switchers Chapter One Introduction About this Manual About the Matrix Switchers CrossPoint / MAV Matrix Switchers • Table of Contents Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.

  • Page 6: About This Manual

    Introduction For more information on any subject in this guide, refer In this manual, the term “video model” refers to any to the CrossPoint 450 Plus / CrossPoint Ultra / CrossPoint or MAV Plus switcher that switches video. MAV Plus User’s Manual, available on the Extron CD In this manual, the term “audio model”...

  • Page 7: Chapter Two • Installation

    Introduction, cont’d CrossPoint / MAV Matrix Switchers Chapter Two Installation Rear Panel Front Panel Configuration Port (Matrix Sizes up to 1616) CrossPoint / MAV Matrix Switchers • Introduction Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.

  • Page 8: Rear Panel

    Installation Rear Panel The MAV Plus switchers are housed in enclosures that range from 8U (figure 2-2) to 2U to support their diffent The CrossPoint 450 Plus 3232 and 2424 are housed in a video format and matrix sizes. The arrangement of 10U high enclosure (figure 2-1).

  • Page 9: Making Connections And Rear Panel Settings

    Installation, cont’d Making connections and rear panel settings Connections for balanced and unbalanced audio inputs (most Turn off power to the input and output devices, and stereo audio models) — Connect balanced or unbalanced disconnect their power cords. audio inputs to these 5-pole captive screw connectors. Video connectors are grouped by video plane.

  • Page 10: Front Panel Configuration Port (Matrix Sizes Up To 1616)

    Installation, cont’d Front Panel Configuration Port Remote port — If desired, connect a control (Matrix Sizes up to 1616) system or computer to the rear panel Remote RS-232/RS-422 port Serial port defaults: RS-232, 9600 baud, no parity, 8-bit, 1 stop bit, no flow control. RS-232 RS-422 All Models...

  • Page 11: Creating A Tie

    Installation, cont’d CrossPoint / MAV Matrix Switchers Chapter Three Front Panel Operation Creating a Tie Saving or Recalling a Preset Setting the Front Panel Locks (Executive Modes) Viewing and Adjusting the Audio Level Viewing Ties (and Muting Outputs) CrossPoint / MAV Matrix Switchers • Installation Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.

  • Page 12: Saving Or Recalling A Preset

    Front Panel Operation Saving or Recalling a Preset The video selection button is labeled “RGBHV” on the CrossPoint switchers and “Video” on the MAV Plus Save a preset — Press and hold the Preset button until it switchers. The two labels are used interchangeably in this flashes.

  • Page 13: Setting The Front Panel Locks (Executive Modes)

    Front Panel Operation, cont’d Setting the Front Panel Locks (Executive Modes) Selecting Lock mode 2 or toggling between mode 2 and mode 1 The matrix switcher has three levels of front panel security lock that limit the operation of the switcher from the front panel. The If the switcher is in Lock mode 0 or mode 1, this procedure three levels are: selects mode 2.

  • Page 14: Viewing Ties (And Muting Outputs)

    Front Panel Operation, cont’d Viewing Ties (and Muting Outputs) CrossPoint / MAV Matrix Switchers Press the View button. Output buttons light for outputs that have no ties established. If the Audio button blinks, audio is broken away (switched separately from video). If an output button blinks, that output is muted.

  • Page 15: Selected Sis Commands

    Remote Control Selected SIS Commands Number of connections A switcher can have up to 200 simultaneous TCP connections, The switchers have Simple Instruction Set (SIS ) commands that ™ including all HTTP sockets and Telnet connections. When you can use for operation and configuration. You can run these the connection limit is reached, the switcher accepts no new commands from a PC connected to either of the switcher’s serial connections until some have been closed.
  • Page 16 Command ASCII command Response Additional description (host to switcher) (switcher to host) Create ties • Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%4*24$. • The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%). N The &...
  • Page 17 Command ASCII command Response Additional description (host to switcher) (switcher to host) Audio output volume Set the audio volume to a specific •Vol value Example: 1*50v Set output 1 volume to 79%. Out01•Vol50 Increment volume Increase volume by 1 step. •Vol Example: Out01•Vol51...

  • Page 18: Installing And Starting The Control Program

    Remote Control, cont’d Installing and Starting the Control Program Another way to operate the switcher is via the Windows -based ® Matrix Switchers Control Program. This program is contained on the Extron Software Products CD-ROM (included with the switcher). Run this program on a PC connected to either of the switcher’s serial ports or the Ethernet port.

  • Page 19: Starting The Program

    • Check for Matrix Updates Starting the program a. Examine the Matrix IP Address field, which displays Click Start > Programs > Extron Electronics > Matrix the last Matrix IP address entered. Switchers > MATRIX Switcher + Control Pgm. If necessary, enter the correct IP address in the field.

  • Page 20: Accessing The Html Pages

    Remote Control, cont’d Accessing the HTML Pages A User name entry is not required. Another way to operate the switcher is via its factory-installed Enter the appropriate administrator or user password in HTML pages, which are always available and cannot be erased the Password field and click OK.
  • Page 21 Remote Control, cont’d CrossPoint / MAV Matrix Switchers • Remote Control 4-14 Refer also to the CrossPoint 450 Plus / CrossPoint Ultra / MAV Plus User’s Manual at www.extron.com.

This manual is also suitable for:

Mav plus seriesCrosspoint ultra series

Table of Contents