Symmetricom TimeProvider 5000 User Manual page 260

Chapter 3
TimeProvider 5000 CLI Command Set
show vlan-config
Use this command to display the VLAN configuration for a specified service port in
IOC and expansion shelf, including VLAN ID, Index value, priority, state, and Host,
Netmask, and Gateway IP address. This command also can be used to display the
VLAN mode for an IOC port or an expansion shelf.
Command Syntax:
To display the VLAN configuration for the specified port:

show vlan-config {ioc1-1 | ioc1-2 | exp[0-9]}
To display the VLAN mode:

show vlan-mode {ioc1 | exp[0-9]}
Example 1:
To display the VLAN configuration info for port 1 on IOC1 -
tp5000> show vlan-config ioc1-1
Results 1:
Idx VID P StT
1 21 0 en
2 22 0 en
3 23 0 en
4 24 0 en
5 25 0 en
6 26 0 en
7 27 0 en
8 82 0 en
9 29 0 en
10 30 0 en
11 31 0 en
12 32 0 en
13 33 0 en
14 34 0 en
15 35 0 en
16 36 0 en
Example 2:
To display the VLAN mode info for IOC1 
tp5000> show vlan-mode ioc1
Results 2:
VLAN Mode Configuration:
ETH1:
ETH2:
260 TimeProvider 5000 User's Guide
Address Netmask
10.11.11.101 255.255.255.0
10.21.21.101 255.255.255.0
10.31.31.101 255.255.255.0
10.41.41.101 255.255.255.0
10.51.51.101 255.255.255.0
10.61.61.101 255.255.255.0
10.71.71.101 255.255.255.0
10.81.81.101 255.255.255.0
10.91.91.101 255.255.255.0
10.101.101.101 255.255.255.0
10.111.111.101 255.255.255.0
10.121.121.101 255.255.255.0
10.131.131.101 255.255.255.0
10.141.141.101 255.255.255.0
10.151.151.101 255.255.255.0
10.161.161.101 255.255.255.0
enable
disable
Gateway/NextHop Destnetwork
10.10.10.1 10.10.10.0/24
20.20.20.1 20.20.20.0/24
30.30.30.1 30.30.30.0/24
40.40.40.1 40.40.40.0/24
50.50.50.1 50.50.50.0/24
60.60.60.1 60.60.60.0/24
70.70.70.1 70.70.70.0/24
80.80.80.1 80.80.80.0/24
90.90.90.1 90.90.90.0/24
100.100.100.1 100.100.100.0/24
10.110.110.1 10.110.110.0/24
10.120.120.1 10.120.120.0/24
10.130.130.1 10.130.130.0/24
10.140.140.1 10.140.140.0/24
10.150.150.1 10.150.150.0/24
10.160.160.1 10.160.160.0/24
098-00028-000 Revision F – May, 2012