Alcatel-Lucent 7210 SAS M Configuration Manual page 354

System Information Commands
Syntax [no] card-type card-type
Context config>system>vwm-shelf>card
Description
This command provides the user a better control over the modules plugged into the 1830 CWDM
device slots. The user can pre-provision acceptable modules by configuring the card-type parameter
with the appropriate card-type vwm-acronym. The modules are identified using the acronyms listed
below.
The 7210 SAS validates the configured card-types with the card-type acronym retrieved from the
clip-on device and checks the following:
If the user has pre-provisioned the card set to administratively up and the module is missing, 7210
SAS raises an event/trap. The event results in a major alarm with the major LED set to the appropriate
color. If the user has pre-provisioned the card and administratively shut it down, 7210 SAS does not
attempt to match the module's identifier (if the module is equipped in the slot) and clear any pending
alarms. 7210 SAS retrieves any information about the equipped module to aid the user with
provisioning.
The no form of the command removes and clears the card-type information. Until the card-type is
provisioned, the 7210 SAS software does not raise any events/traps/alarms for the card and clear all
pending events/traps/alarms/LEDs.
Default
No default
Parameters
card-type — Identifier used to match the configured slot module with the equipped slot module. The
Table 31
modules usable with the clip-on device.
Page 354
Guide
• If the configured card-type matches the card-type acronym retrieved from the clip-on device,
7210 SAS allows management of the module.
• If the configured card-type does not match the card-type acronym retrieved from the clip-on
device, 7210 SAS raises an event to alert the user of mismatch in configuration. The event results
in a major alarm with the major LED set. In such a case, the card status displays "Provisioning
Mismatch" error.
• The mismatch event/trap is cleared if the module is replaced with the one that has a correct card-
type acronym. Any pending trap/event, major alarm and major LED is cleared.
and Table 32 below provides the list of acronyms that can be used to identify the supported
Values
CWDM:
SFC1A SFC1B SFC1C SFC1D SFC1E SFC1F SFC1G SFC1H SFC2A&B
SFC2C&D SFC2E&F SFC2G&H SFC4A-D SFC4E-H SFC8
DWDM:
ANY|EALPFG|SFD8A_R|SFD8B_R|SFD8C_R|SFD8D_R|SFD4A_R|SFD4B_R|S
FD4C_R|SFD4D_R|SFD4E_R|SFD4F_R|SFD4G_R|SFD4H_R|SFD2A_R|SFD2B
_R|SFD2C_R|SFD2D_R|SFD2E_R|SFD2F_R|SFD2G_R|SFD2H_R|SFD2I_R|SF
D2L_R|SFD2M_R|SFD2N_R|SFD2O_R|SFD2P_R|SFD2Q_R|SFD2R_R|SFD8A|
SFD8B|SFD8C|SFD8D|SFD4A|SFD4B|SFD4C|SFD4D|SFD4E|SFD4F|SFD4G|SF
D4H|SFD2A|SFD2B|SFD2C|SFD2D|SFD2E|SFD2F|SFD2G|SFD2H|SFD2I|SFD2
L|SFD2M|SFD2N|SFD2O|SFD2P|SFD2Q|SFD2R
ascii-string - can use ASCII alphabets or numbers. Valid card-type acronyms is
listed in the table below.
7210 SAS M, T, X, R6 Basic System Configuration