Dtc P0300 Multiple Cylinder Misfire - Daewoo MATIZ Service Manual

DIAGNOSTIC TROUBLE CODE (DTC) – P0300 MULTIPLE CYLINDER MISFIRE
System Description
The Engine Control Module (ECM) monitors the crank-
shaft and camshaft positions to detect if the engine is
misfiring. The ECM looks for a quick drop in crankshaft
speed. This test is executed in blocks of 100 engine rev-
olution tests. It may take between one to several tests to
store a Diagnostic Trouble Code (DTC) and illuminate
the Malfunction Indicator Lamp (MIL). Under light misfire
conditions, it may also take more than one trip to set a
DTC. Severe misfire will flash the MIL, indicating that
catalyst damage is possible.
Conditions for Setting the DTC
D Emission threshold is 3.0% for automatic transaxle
and 3.0% for manual transaxle.
D 20 engine cycles have occurred since cranking has
started.
D A/C compressor clutch has not just engaged or disen-
gaged.
D Engine load and engine speed are in a detectable re-
gion and are at or above zero torque.
D Camshaft Position (CMP) sensor is in synchroniza-
tion.
D Electric Exhaust Gas Recirculation (EEGR) flow
diagnostic is not in progress.
D Fuel level is greater than or equal to 20% of rated
tank capacity.
D Decel Fuel Cutoff (DFCO) not active.
D Fuel is not shutoff from high engine speed of 6500
rpm for manual transaxle vehicle or 6500 rpm in drive
and 6250 rpm in park for automatic transaxle ve-
hicles.
D Fuel is not shutoff at 255 km/h (158 mph).
D An automatic transmission is not shifting.
D Throttle position change is less than 3% per 125 ms.
D Vehicle has not encountered an abusive engine
speed of 7000 rpm.
D Crankshaft speed patters are normal.
Step
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
1
Was the check performed?
1. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON, with the engine OFF.
2
3. Request Diagnostic Trouble Codes (DTCs)
Are DTCs P0201, P0202, P0203, P0204 set?
DAEWOO M-150 BL2
DTC P0300 – Multiple Cylinder Misfire
Action
ENGINE CONTROLS 1F – 139
D Throttle position is less than 4% when vehicle speed
is greater than 10 km/h (6 mph).
D Engine speed is between 600 and 4500 rpm.
D Vehicle voltage is between 11 and 16 volts.
D Engine Coolant Temperature (ECT) is between –7°C
(20°F) and 120°C (248°F).
D The engine speed is less than or equal to 1800 rpm or
the crank angle sensing error has not been learned.
D There is the correct ratio between Crankshaft Posi-
tion (CKP) sensor pulses and CMP sensor pulses.
D DTCs P0106, P0107, P0108, P0117, P0118, P0122,
P0123, P0320, P0337, P0341, P0342 and P0502 are
not set.
Action Taken when the DTC Sets
D Emission related.
D "Armed" after two trip with a fail.
D "Disarmed" after one trip with a pass.
D MIL on if failure is detected in three consecutive trips.
D Stores a History DTC on the third consecutive with a
fail (The DTC will be armed after the second fail).
D Stores a Freeze Frame on the third consecutive trip
with a fail (if empty).
Conditions for Clearing the MIL/DTC
D The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
D A history DTC will clear after 40 consecutive warm up
cycles without a fault.
D DTC(s) can be cleared by using the scan tool.
D Disconnecting the ECM battery feed for 10 seconds.
Diagnostic Aids
An intermittent can also be the result of a defective re-
luctor wheel. Remove the CKP sensor and inspect the
reluctor wheel through the sensor mount hole. Check for
porosity and the condition of wheel. If the DTC is inter-
mittent refer to "Symptoms Diagnosis" in this section.
Value(s)
–
Go to Step 2
–
Applicable DTC
Yes No
Go to
"On-Board
Diagnostic
System Check"
Go to
table
Go to Step 3