Dentsply Sirona inFire HTC speed Manuals

Dentsply Sirona inFire HTC speed Manuals

Manuals and User Guides for Dentsply Sirona inFire HTC speed. We have 2 Dentsply Sirona inFire HTC speed manuals available for free PDF download: Service Manual, Operating Instructions Manual

Dentsply Sirona inFire HTC speed Service Manual

Dentsply Sirona inFire HTC speed Service Manual (62 pages)

Brand: Dentsply Sirona | Category: Furnace | Size: 4.28 MB

Table of Contents

Table of Contents
2
Important Information
5
General Information
5
Technical Data
6
Safety Information
8
How Does Infire HTC Work
10
Functional Diagram
10
Description of the Furnace
11
Circuit Diagram
12
Up to Serial No. 3000
12
From Serial No. 3000
13
System Overview
14
Front View
14
Rear View
16
Wiring Diagram
17
Tools
18
Initializing the Controller
20
Troubleshooting
21
Error Messages from Electronic Components
21
Error Message: SENSOR BROKEN
21
Error Message: SENSOR
22
Error Message: TURN-OFF
22
Error Message: POWER FAILURE
22
Error Without Message on the Display
23
Error: Wrong Time Displayed
23
Error: Furnace Does Not Heat up Although Autostart Program Is
23
Error: LED on Control Panel Indicates Heating, but Furnace Does Not
24
Error: Controller Board "Forgets" the Stored Programs
25
Error: Controller Board "Forgets" the Time
25
Error: no Display Reading, Yellow Pilot Light of ON/OFF Switch Is on
25
Diode Flashes Briefly
25
Error: no Display Reading, Yellow Pilot Light Is On, Diode Is Not Lit
26
Error: no Display Reading, Yellow Pilot Light Is off
26
Error: Furnace Triggers Circuit Breaker
27
Error: Furnace Triggers the Circuit Breaker in the Fuse Box
27
Error: the Furnace Door Does Not Close
28
Replacing Parts
29
Replacing the Heating Element
29
Resetting the Counter after Replacing the Heating Element
30
Replacing the Controller Board
30
Resetting the Counter after Replacing the Controller Board
31
Replacing the Storage Battery
32
Resetting the Counter after Replacing the Storage Battery
32
Replacing Main Fuses
32
Replacing Fuses
33
Replacing the Thermocouple
33
Replacing the Fan
33
Replacing the Sintering Chamber
34
Upgrading
38
Upgrading to Superspeed
38
Scope of Supply
38
Required Tools
39
Introduction
39
Procedure
40
Disconnect the Power Supply
40
Removing the Regulator Board
41
Unscrewing the Control Panel
43
Installing the New Regulator Board
43
Installing the New Control Panel
43
Final Work
44
Updating the Control Software
45
Upgrading to Non-Precious Metal Sintering
49
Scope of Supply
49
Required Tools
50
Preparation
51
Disconnect the Power Supply
51
Opening the Rear Panel of the Unit
51
Procedure
52
Install the Front Coupling
52
Install the Rear Coupling
53
Installing the Gas Management Module
54
Connecting Cables to the Regulator Board
56
Installing the Rear Panel of the Unit
56
Final Work
57
Modifying the Furnace Door
57
Assembling the Furnace Door with the Gas Socket
58
RS232 Interface
60
Temperature Difference Output
60
Service Codes
61

Advertisement

Dentsply Sirona inFire HTC speed Operating Instructions Manual

Dentsply Sirona inFire HTC speed Operating Instructions Manual (56 pages)

Brand: Dentsply Sirona | Category: Medical Equipment | Size: 1.77 MB

Table of Contents

Table of Contents
2
Dear Customer
5
General Data
6
Structure of the Document
6
- Identification of the Danger Levels
  6
- Formats and Symbols Used
  7
Warranty
7
Safety Information
8
Technical Description
11
Description of the Furnace
11
Certification
12
Intended Use
12
Technical Data
13
Setup
14
Installation Site
14
Electrical Connection
15
Operation
17
Controls and Displays
17
- Key Functions
  18
- Description of the Standby Display
  18
Switching on the Unit
19
Practical Use
19
- Initial Startup
  20
- Sintering Zirconium Oxide
  20
  - Preparing the Sintering Tray
    20
  - Preparing the Furnace Door
    21
- Program Selection
  26
- Loading a Program
  26
- Starting the Program
  26
- Lifting the Sintering Tray out of the Furnace
  26
Operating Modes
26
- Super Speed Sintering
  26
  - Performing Super Speed Sintering
    27
- Speed Sintering
  29
- Classic Sintering
  30
Non-Precious Metal (NPM) Sintering (Optional)
30
Programs
38
Default Settings
44
Display and Acoustic Signal
44
Adjustment of the Start Time (Casting Time Function)
45
Description of Special Functions
46
Sintering with Ventilation (Sintering with a Small Air Gap)
46
Sintering with Pre-Drying (Sintering with a Large Air Gap)
46
Pre-Drying Without Sintering
46
Sintering with Defined Cooling
46
Regular Care
47
General Care Instructions
47
Sirona Service Program
47
Maintenance

48
Malfunctions

50
- Error Messages from Electronic Components
  50
- Miscellaneous Errors and Their Causes
  51
Disposal

52
- Index
  53

Advertisement

Related Products

Dentsply Sirona Categories

Dental equipment Medical Equipment Lighting Equipment Science Education products

Switch

More Dentsply Sirona Manuals