EWM Phoenix 401 Progress puls MM FKW Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.8.3
5.8.4
5.8.5
5.8.6
5.8.7
5.8.8
5.8.9
5.8.10
5.8.11
5.8.12
5.8.13
5.8.14
5.8.15
5.8.16
5.9 TIG welding .................................................................................................................................. 77
5.9.1
5.9.2
5.9.3
5.9.4
5.9.5
5.9.6
5.9.7
5.10 MMA welding ................................................................................................................................ 84
5.10.1
5.10.2
5.10.3
5.10.4
5.10.5
5.10.6
5.10.7
5.11 Remote control ............................................................................................................................. 87
5.12 Interfaces for automation ............................................................................................................. 87
5.12.1
5.12.2
5.12.3
4
5.8.2.5 Spool brake setting ........................................................................................ 43
Definition of MIG/MAG welding tasks ........................................................................... 44
Welding task selection .................................................................................................. 44
5.8.4.1 Basic welding parameters ............................................................................. 44
5.8.4.2 Operating mode ............................................................................................. 44
5.8.4.3 Welding type (MIG/MAG standard/pulse arc welding) .................................. 44
5.8.4.4 Choke effect / dynamics ................................................................................ 45
5.8.4.5 superPuls ...................................................................................................... 45
5.8.4.6 Burn-back ...................................................................................................... 46
MIG/MAG operating point ............................................................................................. 47
5.8.5.1 Selecting the display unit............................................................................... 47
5.8.5.2 Operating point setting using material thickness .......................................... 47
5.8.5.3 Arc length correction setting .......................................................................... 48
5.8.5.4 Accessory components for operating point setting ....................................... 48
MIG/MAG welding data display .................................................................................... 48
forceArc / forceArc puls ................................................................................................ 49
rootArc/rootArc puls ...................................................................................................... 50
MIG/MAG functional sequences / operating modes ..................................................... 51
5.8.9.1 Explanation of signs and functions ................................................................ 51
Conventional MIG/MAG Welding (GMAW non synergic) ............................................. 64
5.8.10.1 Setting the operating point (welding output).................................................. 64
MIG/MAG program sequence ("Program steps" mode) ............................................... 65
5.8.11.1 Selection of the program sequence parameter ............................................. 65
5.8.11.2 MIG/MAG overview of parameters ................................................................ 66
5.8.11.3 Example, tack welding (non-latched) ............................................................ 67
5.8.11.4 Example, aluminium tack welding (non-latched special) .............................. 67
5.8.11.5 Example, aluminium welding (latched special) ............................................. 68
5.8.11.6 Example, visible seams (latched super pulse) .............................................. 69
Main program A mode .................................................................................................. 70
5.8.12.1 Selecting parameters (program A) ................................................................ 72
MIG/MAG automatic cut-out ......................................................................................... 72
Standard MIG/MAG torch ............................................................................................. 73
MIG/MAG special-torches............................................................................................. 73
5.8.15.1 Program- and Up- / down operation .............................................................. 73
5.8.15.2 Switching between Push/Pull and intermediate drive ................................... 74
Expert menu (MIG/MAG) .............................................................................................. 75
5.8.16.1 Selection ........................................................................................................ 75
Welding torch and workpiece line connection .............................................................. 77
Welding task selection .................................................................................................. 78
Welding current setting ................................................................................................. 78
TIG arc ignition ............................................................................................................. 78
5.9.4.1 Liftarc ignition ................................................................................................ 78
Function sequences/operating modes .......................................................................... 79
5.9.5.1 Explanation of signs and functions ................................................................ 79
TIG automatic cut-out ................................................................................................... 82
TIG program sequence ("Program steps" mode) ......................................................... 83
Connecting the electrode holder and workpiece lead .................................................. 84
Welding task selection .................................................................................................. 85
Welding current setting ................................................................................................. 85
Arcforce......................................................................................................................... 85
Hotstart ......................................................................................................................... 86
Antistick......................................................................................................................... 86
Parameter overview ...................................................................................................... 86
Automation interface ..................................................................................................... 88
Remote control connection socket, 19-pole ................................................................. 89
RINT X12 robot interface .............................................................................................. 90
099-005323-EW501
21.05.2014