Setting The Bundled Software After Completion Of Installation - Fujitsu PRIMEQUEST 2000 Series Installation Manual

CHAPTER 4 Installation of Operating System and bundled software
4.4 Procedures to install Windows into internal HDD/SSD

4.4.4 Setting the bundled software after completion of installation

After completion of operating system installation, set the bundled software.
1. Install OneCommand Manager in the following cases.
- When the Emulex FC card or Converged Network Adapter Card is mounted
and
- When the OneCommand Manager is not installed.
It can be judged whether [Emulex] -[OneCommand Manager] exist under [Start] menu-[All programs] in the
installation status of OneCommand Manager.
Note
In Windows Server 2012 or Windows Server 2012 R2, "the [start] menu – [all programs]" should read "the [start]
menu – [all apps]".
a. Download the driver/utility of FC card or Converged Network Adapter Card from the following URL.
http://support.ts.fujitsu.com/
Note:
The driver/utility can be used in the PRIMEQUEST 2000 series though PRIMERGY is described in the
downloaded binary.
b. Double click the downloaded file and execute it.
The prompt screen of cmd.exe (black window) is displayed for a while and the file is extracted.
c. The window is closed automatically when the extraction is completed.
The downloaded file is uncompressed, and the folder or the file is created newly.
Remark
When the window is not closed even if displayed as [Complete] in the title bar of the window, click the [Close]
button and close the window.
d. Double-click the " elxocm-windows-x86-XXXXX.exe"(in case of x86, 32-bit OS) or "elxocm-windows-x64-
XXXXX.exe"(in case of x64, 64-bit OS) in the "FC_vXXXXXX" directory created in the decompression, and
execute it.
Remark
"XXXXX" shows the version number. Read it in different way properly.
2. Qlogic Converge Console (GUI/CLI) is installed in the following cases.
- When the Qlogic FC card is mounted.
And
- When Qlogic Converge Console (GUI/CLI) is not installed
The installation condition of Qlogic Converge Console (GUI) is determined by the presence of [Qlogic Corporation] –
[QCC GUI(localhost)] or [QCC GUI(127.0.0.1)] under the [start] menu – [all programs]
The installation condition of Qlogic Converge Console (CLI) is determined by the presence of [Qlogic Management
Suite] -[QConvergeConsole CLI] under the [start] menu – [all programs]
Note
In Windows Server 2012 or Windows Server 2012 R2, "the [start] menu – [all programs]" should read "the [start]
menu – [all apps]".
a. Driver/ Utility of FC Card is downloaded from the following URL.
http://support.ts.fujitsu.com/
Note
Driver/Utility can be used by the PRIMEQUEST 2000 series though PRIMERGY is described in the
downloaded binary.
b. The downloaded file is executed by a double click.
The prompt window of cmd.exe (black window) is displayed for a while and the file is extracted.
c. The window closes automatically after the extraction is completed.
The download file is extracted and folder or file is newly created.
Remark
If the window does not close even if "Complete" is displayed on the title bar of the window then click the "Close"
button and close the window.
d. Double click and execute "QConvergeConsole_Installer_Windows_XXXXX.exe" in "QCC_vXXXXXX" directory
created by extraction.
Remark
"XXXX" shows the version number. Read properly.
3. When the installation is completed, reboot the partition.
4. Check the setting of management LAN.
The STP function of the port to be connected is turned OFF when the management LAN is used for communication
with MMB in the switching hub which supports the STP function.
5. Set the trap destination and Mail Sending destination through MMB.
67
CA92344-0536-04