Pentek 6230 Operating Manual page 197

Pin
No. Mnemonic
1 NTEST_OUT/ADD
THERM
2
3 SDA
4 SCL
5 FAN1/AIN1
6 FAN2/AIN2
7 CI
8 GND
9 V
CC
INT
10
11 NTEST_IN/AOUT
RESET
12
13 D1–
14 D1+
15 +12 V
IN
16 +5 V
IN
17 V /D2–
CCP2
18 +2.5 V /D2+
IN
19 +V
CCP1
20 VID4/IRQ4
21 VID3/IRQ3
22 VID2/IRQ2
23 VID1/IRQ1
24 VID0/IRQ0
REV. A
PIN FUNCTION DESCRIPTIONS
Description
Digital I/O. Dual Function pin. This is a three-state input that controls the 2 LSBs of the Serial
Bus Address. This pin functions as an output when doing a NAND test.
Digital I/O. Dual Function pin. This pin functions as an interrupt output for temperature interrupts
only, or as an interrupt input for fan control. It has an on-chip 100 kΩ pull-up resistor.
Digital I/O. Serial Bus bidirectional Data. Open-drain output.
Digital Input. Serial Bus Clock.
Programmable Analog/Digital Input. 0 V to 2.5 V analog input or digital (0 to V
tachometer input.
Programmable Analog/Digital Input. 0 V to 2.5 V analog input or digital (0 to V
tachometer input.
Digital I/O. An active high input from an external latch which captures a Chassis Intrusion event.
This line can go high without any clamping action, regardless of the powered state of the ADM1024. The
ADM1024 provides an internal open drain on this line, controlled by Bit 6 of Register 40h or Bit 7 of
Register 46h, to provide a minimum 20 ms pulse on this line, to reset the external Chassis Intrusion Latch.
System Ground.
POWER (2.8 V to 5.5 V). Typically powered from 3.3 V power rail. Bypass with the parallel combination of
10 µF (electrolytic or tantalum) and 0.1 µF (ceramic) bypass capacitors.
Digital Output. Interrupt Request (open-drain). The output is enabled when Bit 1 of Register 40h
is set to 1. The default state is disabled. It has an on-chip 100 kΩ pull-up resistor.
Digital Input/Analog Output. An active-high input that enables NAND Test mode board-level connectivity
testing. Refer to section on NAND testing. Also functions as a programmable analog output when NAND
Test is not selected.
Digital I/O. Master Reset, 5 mA driver (open drain), active low output with a 45 ms minimum pulsewidth.
Set using Bit 4 in Register 40h. Also acts as reset input when pulled low (e.g., power-on reset). It has an
on-chip 100 kΩ pull-up resistor.
Analog Input. Connected to cathode of first external temperature sensing diode.
Analog Input. Connected to anode of first external temperature sensing diode.
Programmable Analog Input. Monitors 12 V supply.
Analog Input. Monitors 5 V supply.
Programmable Analog Input. Monitors second processor core voltage or cathode of second external
temperature sensing diode.
Programmable Analog Input. Monitors 2.5 V supply or anode of second external temperature sensing diode.
Analog Input. Monitors 1st processor core voltage (0 V to 3.6 V).
Digital Input. Core Voltage ID readouts from the processor. This value is read into the VID4 Status Regis-
ter. Can also be reconfigured as an interrupt input. It has an on-chip 100 kΩ pull-up resistor.
Digital Input. Core Voltage ID readouts from the processor. This value is read into the VID0–VID3 S tatus
Register. Can also be reconfigured as an interrupt input. It has an on-chip 100 kΩ pull-up resistor.
Digital Input. Core Voltage ID readouts from the processor. This value is read into the VID0-VID3 S tatus
Register. Can also be reconfigured as an interrupt input. It has an on-chip 100 kΩ pull-up resistor.
Digital Input. Core Voltage ID readouts from the processor. This value is read into the VID0–VID3 Status
Register. Can also be reconfigured as an interrupt input. It has an on-chip 100 kΩ pull-up resistor.
Digital Input. Core Voltage ID readouts from the processor. This value is read into the VID0–VID3 Status
Register. Can also be reconfigured as an interrupt input. It has an on-chip 100 kΩ pull-up resistor.
–5–
ADM1024
) amplitude fan
CC
) amplitude fan
CC