Pentek 6210 Operating Manual page 138

AD603–SPECIFICATIONS
Model
Parameter
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Noise Spectral Density
Noise Figure
1 dB Compression Point
Peak Input Voltage
OUTPUT CHARACTERISTICS
–3 dB Bandwidth
Slew Rate
2
Peak Output
Output Impedance
Output Short-Circuit Current
Group Delay Change vs. Gain
Group Delay Change vs. Frequency V
Differential Gain
Differential Phase
Total Harmonic Distortion
3rd Order Intercept
ACCURACY
Gain Accuracy
T to T
MIN MAX
3
Output Offset Voltage
T to T
MIN MAX
Output Offset Variation vs. V
T to T
MIN MAX
GAIN CONTROL INTERFACE
Gain Scaling Factor
T to T
MIN MAX
GNEG, GPOS Voltage Range
Input Bias Current
Input Offset Current
Differential Input Resistance
Response Rate
POWER SUPPLY
Specified Operating Range
Quiescent Current
T to T
MIN MAX
NOTES
1
Typical open or short-circuited input; noise is lower when system is set to maximum gain and input is short-circuited. This figure includes the effects of both voltage
and current noise sources.
Using resistive loads of 500 Ω or greater, or with the addition of a 1 kΩ pull-down resistor when driving lower loads.
2
The dc gain of the main amplifier in the AD603 is ×35.7; thus, an input offset of 100 µV becomes a 3.57 mV output offset.
3
4
GNEG and GPOS, gain control, voltage range is guaranteed to be within the range of – V
Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min
and max specifications are guaranteed, although only those shown in boldface are tested on all production units.
Specifications subject to change without notice.
(@ T = 25 C, V
A
Range, R = 500
L
Conditions
Pins 3 to 4
1
Input Short Circuited
f = 10 MHz, Gain = max, R
f = 10 MHz, Gain = max, R
V = 100 mV rms
OUT
≥ 500 Ω
R
L
≥ 500 Ω
R
L
f ≤ 10 MHz
f = 3 MHz; Full Gain Range
= 0 V; f = 1 MHz to 10 MHz
G
f = 10 MHz, V
OUT
f = 40 MHz, Gain = max, R
–500 mV ≤ V ≤ +500 mV
G
V = 0 V
G
–500 mV ≤ V ≤ +500 mV
G G
4
Pins 1 to 2
Full 40 dB Gain Change
= 5 V, –500 mV ≤ V ≤ +500 mV, GNEG = 0 V, –10 dB to +30 dB Gain
S G
, and C = 5 pF, unless otherwise noted.)
L
= 10 Ω
S
= 10 Ω
S
= 1 V rms
= 50 Ω
S
+ 4.2 V to +V – 3.4 V over the full temperature range of –40°C to +85°C.
S S
–2–
AD603
Min Typ Max
97 100 103
2
1.3
8.8
–11
± 1.4 ± 2
90
275
± 2.5 ± 3.0
2
50
± 2
± 2
0.2
0.2
–60
15
± 0.5
1
± 1.5
20
30
20
30
39.4 40 40.6
38 42
–1.2 +2.0
200
10
50
40
± 4.75 ± 6.3
12.5 17
20
Unit
Ω
pF
nV/√Hz
dB
dBm
V
MHz
V/µs
V
Ω
mA
ns
ns
%
Degree
dBc
dBm
dB
dB
mV
mV
mV
mV
dB/V
dB/V
V
nA
nA
MΩ
dB/µs
V
mA
mA
REV. D