ROBBE-Futaba FX-32 Instruction Manual page 119

switch to the data input mode.
Select the function by scrolling the touch
sensor and touch the RTN button.
2. When you want to link this mix with other
mixes, move the cursor to the [LINK] item and
touch the RTN button to switch to the data
input mode.
Set the link mode to [+] or [-] by scrolling the
touch sensor and touch the RTN button.
*Check the direction by actual operation.
●Trim mode ON/OFF setting
1. When changing the trim mode, move the
cursor to the [TRIM] item and touch the RTN
button to switch to the data input mode.
Select ON/OFF by scrolling the touch sensor
and set the selection by touching the RTN
button.
*When mixing includes master side trim, select [ON] and
when mixing does not include master trim, select [OFF].
*Effective when a function is set at the master channel.
●Slave channel AFR mode setting (STK-STK)
1. Move the cursor to the [STK-STK] item, select
the mode by scrolling the touch sensor,
and change the mode by touching the RTN
button.
*When link is set at the slave side, and you want to add AFR
(D/R) to the mixing rate, select [ON].
*This is effective when the linkage is the same, but the travels
are substantially different.
●Mixing curve setting
(For a description of the curve setting method, see the
description at the back of this manual.)
●Fine tuning trim setting
Operation control [CTRL], operation mode
[MODE], and rate [RATE] adjustment is possible
by [FINE TUNING] item.
(For a description of the fine tuning trim setting method, see
the description at the back of this manual.)
●Servo speed setting
Adjustment is possible with the [SPEED] item.
(For a description of the servo speed setting method, see the
description at the back of this manual).
●Mixing ON/OFF delay setting
Delay time at mix ON [START] and delay time
at mix OFF [STOP] adjustment is possible by
[DELAY] item.
*This function is inactive when a mixing switch is not set.
1. Move the [START] or [STOP] item and touch
the RTN button to switch to the data input
mode.
2. Adjust the delay time by scrolling the touch
sensor.
Initial value: 0.0 sec
Adjustment range: 0~4 sec
(When the RTN button is touched for 1 second, the delay time
is reset to the initial value.)
Touch the RTN button to end adjustment and
return to the cursol move mode.
●Offset mode setting
O f f s e t m o d e i s f u n c t i o n w h i c h a l l o w s
simultaneous offset control of up 4 slave functions
per circuit.
1. Use [MODE] setting to select the program
mixing oparation mode. [MIXING] is the
normal mixing mode and [OFFSET] is the
offset mode.
2. Move the cursor to [INHIBIT] of the mixing No.
set to the offset mode and touch the RTN
button. The setup screen is displayed.
3. Press the S1 button. Page 5/5 is displayed.
4. Move the cursor to the [STATUS] item and
switch to the date input mode by touching
the RTN button.
5. Turn the dial to the left and right until [ACT]
blinks, and then touch the RTN button. To
deactivate the function, switch to [INH].
●ON/OFF switch selection
Move the cursor to the page 5/5 [SWITCH]
i t e m , c a l l t h e s w i t c h s e t u p s c r e e n b y
touching the RTN button, and then select
the switch and ON direction. (For a detailed
description of the selection method, see
[Switch Selection Method] at the back of the
instruction manual.)
●Slave No. selection
Setting of the slave No. from 1 to 4 at pages
1/5~4/5 is displayed. When the S1 button is
pushed, the displayed slave No. is switched.
●Slave function setting
Move the cursor to the [FUNCTION] item and
switch to the date input mode by touching
the RTN button. Select the function by
scrolling the dial and then touch the RTN
button.
●Offset rate setting
The function operation offset amount when
the mixing switch is ON and OFF can be set
independently.
1. Move the cursor to the [ON] or [OFF] item
and switch to the date input mode by
touching the RTN button.
2. Turn the dial to the left and right and set the
offset rate when the switch is ON or OFF.
Initial setting : 0%
Setting range : -300%~+300%
<Model Menu (Common Functions)> 119