Program Summary Guide; Users - Assa Abloy S series Installation & Programming Manual

'
S series
The following program summary is an abbreviated version of all the panel program addresses. This is intended as a quick
guide to finding a program address. In many address locations, there is a main address (e.g. "P1E"), then a sub address
(e.g. P1E "1E"). You must enter in the main address number, followed by the sub address, then you can enter the actual
data. The program addresses are in numerical order with page references beside them so you can get more detailed
information if required. This Summary is split into 11 headings. These are;
1) Users Programming
2) Miscellaneous Panel & Clock Settings
3) Outputs
4) Areas
5) Keypads
6) Key-Switches
7) Zones
P1E 1-100E User Code 1-100 -
NOTE: The 100 Users can be keypad Code, Radio or Access key Users. They can be mixed but the Maximum is 100 Users.
The User type MUST be set to "0" (P2E User# E) for a code to be entered at the above address
P2E 1-100E User # 1-100 Type -
(Default = 0)
P3E 1-100E User # 1-100 Area -
(Default = 1)
P4E 1-100E Users 1-100 Access Options
(Default = 1,3,4)
P5E 1-100E Users 1-100 Privileges
(Default User 1 = 2,3,4,5,6,7,8)
(Default User 2-100 = All Off)
P7E 21-100E Radio User 21-100 Type
(Default = 0)
P8E 21-100E Radio Users 21-100 Privileges
(Default = 1)
'
SUMMARY GUIDE
Page 38
Page 44
Page 49
Page 52
Page 58
Page 66
Page 67

USERS

Default for User Code # 1 (P1E1E) = 1234 Codes can be 1-6 or 4-6 digits
(where 1E = User Code #1 to 100E = User Code #100)
0 = Keypad Code User {PIN}
1 = Radio User (Users 21-100 only)
2 = Access Tag/Card User
3 = Both Code and Access Tag/Card User {Tag + PIN)
4 = Either Code or Access Tag/Card User {Tag or PIN}
1 = Assigned to Area "A"
2 = Assigned to Area "B"
(Default 1-4
8) Time Zones
9) Dialler
10) Telephone Numbers
11) Miscellaneous 4+2 Program Options
12) SIA Report Codes -
13) Panel Diagnostic & Default Options
.
User Type (Code/Radio/Access Tag-Card)
) 1 = Code can Arm Area
2 = Code can arm Stay Mode
3 = Code can Disarm Area
4 = Code can disarm Stay Mode
5 = Code is a Security Guard Code
6 = Code will Arm Latchkey Mode
7 = Call Divert Code
8 = Can View Event Memory
1 = User can Change their Code
2 = User can Change All Codes
3 = User can Allow Access to Installer Mode/Edit all Codes
4 = User can Change Telephone Numbers
5 = User can Change the Clock
6 = User can Change DTMF Command Codes
7 = User can Learn New Radio Devices
8 = User can Force a Download to Callback Number
0 = General Pendant Type
1 = Crow Freelink Pendant
21 = Ness Pendant
1 = Pendant Can Disarm at All Times
2 = Pendant Causes Immediate Panic
3 = Pendant Causes Delayed Panic ( 1.5 Sec)
4 = Pendant only works during Entry Delay
5 = This User is a Duress Code (Users 21-100)
6 = Spare
7 = Spare
8 = Spare
93
PROGRAM
Page 77
Page 78
Page 82
Page 88
Page 90
Page 90
Programming User Codes
.
User Area Assignment
User Code Access Options
User Code Privileges
Radio User Type
Radio User Privileges
Page 38
Page 38
Page 39
Page 39
Page 40
Page 40
Page 41