Outputs; Output Options: A/B/C/D - Assa Abloy S series Installation & Programming Manual

P26E4E so that the panel knows that Daylight Saving Time is currently active. Failure to do this will not allow the clock
to automatically adjust to the correct time when Daylight Saving Time Ends.
DAYLIGHT SAVING START SUNDAY - P27E 1E (Value 0-5, 0= DLS Disabled)
DAYLIGHT SAVING END SUNDAY -
DAYLIGHT SAVING START MONTH -
DAYLIGHT SAVING END MONTH -
DAYLIGHT SAVING START HOUR -
DAYLIGHT SAVING END HOUR -
If Daylight Saving (DLS) is used, the actual start and stop details can be entered here and the clock will automatically
adjust for daylight saving.
NOTE: If the start and/or stop Sunday (P27E above) must be the last Sunday of the month (which can be Sunday
number 4 or 5 depending on the year) then you must se the value to 5.
NOTE: With all output programming options we refer to outputs 1-8. Only outputs 1-4 are available as standard,
with outputs 5-8 requiring the connection of the optional 4 way output expander unit that connects to the
keypad buss ( the output expander provides 4 change-over relay contacts).
OUTPUT OPTIONS "A" - P34E 1-8E
Option 1 - Invert Output
Option 2 - Flash Output
Option 3 - Single Pulse to Output
Option 4 - Lockout Output
Option 5 - DTMF Remote Control of Output
Option 6 - Keypad User can Operate Output
Option 7 - <CONTROL> button can Operate Output
Option 8 - Pulsed Chime Alarm (linked to pulse timer)
Option 1 Invert Output - This option is used to invert the normal state of the output. The panel uses open
collector transistor switches and the default state of all outputs is off (open). When in alarm the
transistor is turned on and the output goes low (0V). The invert option reverses this function.
Option 2 Flash Output - When the output is turned on this option causes the output to flash at a rate set by the
pulse timer (P39E). One use is to flash a lamp during an alarm. DO NOT turn this option on if the Output
is to be manually controlled by a user or the "Control" button.
Option 3 Single Pulse to Output - This option produces a single pulse at the output when an alarm occurs (the
pulse time is the value programmed at the output pulse timer P39E).
Option 4 Lockout Output - This option is used to limit the output to one operation per arming period.
Option 5 DTMF Remote Control of Output - If the panel is set-up so a User can dial in from a remote telephone to
perform "DTMF Code Control" (P175E12E) of the Outputs, this option selects which Outputs are able to
be controlled by the remote user.
Option 6 Keypad User can Operate Output - If a DTMF Output control code is programmed into the panel
(P175E12E), the same code can be entered at the panel keypad to allow local control of the Outputs
selected at this address.
Option 7 <Control> button can Operate Output - The <Control> button on the keypad can also be used to turn
outputs on or off. For that to happen this option must be turned on for the output/s concerned. To turn
an output on locally at the keypad the operator simply presses the <Control> button for 2 seconds at
which time the "Control" LED will illuminate on an LED keypad or the word "OUTPUTS" will appear on
the LCD keypad to indicate that the Control mode is active. If any controllable outputs are currently on
they will be indicated at the keypad. The operator can now press a button relating to the output/s they
wish to control eg pressing the "1" button will turn output 1 on or off, The "2" button for output 2 etc.
When finished the operator then presses the <ENTER> button to cancel the Control mode and return to
normal.
P27E 2E (Value 0-5, 0= DLS Disabled)
P28E 1E (Value 1-12)
P28E 2E (Value 1-12)
P29E 1E (Value 0-23)
P29E 2E (Value 0-23)

OUTPUTS

OUTPUT OPTIONS "A"
49