User Code Privileges; Radio User Type - Assa Abloy S series Installation & Programming Manual

option 6) or the key-switch (see P112E option 6). If a User with this option ON Disarms the alarm no
Latchkey Disarm report will be sent via the dialler. If Latchkey Mode is Armed and a user with this
option turned OFF Disarms the alarm a Latchkey disarm report will be sent to alert parents when their
children have returned home. Reporting of Latchkey Disarm is enabled at location (P189E option 1). If a
Voice report is desired the message is assigned at P176E10E. Normally you would select a telephone
number/s set for domestic or voice reporting to report the Latchkey disarm signal.
Option 7 User can set Call Divert Mode on Arm/Disarm - If a User has option 7 on, they can initiate the Call
Divert Number/s to be dialled on Arm/Disarm. This allows automatic call diversion when the alarm is
Armed and taking the diversion off when Disarmed. Call divert must also be programmed (P192-194E).
Option 8 User can View Event Memory - If access to memory mode is restricted by turning on option 8 at
location P25E13E, this option allows the user to access memory mode by pressing <MEMORY> <CODE
#> <ENTER>. If this option is off and memory access is restricted, the user cannot view memory mode.
USER CODE PRIVILEGES - P5E 1-100E (see chart on page 114 for the exact program locations)
Option 1 - User can Change Their Code
Option 2 - User can Change All Codes
Option 3 - User can Allow Access to Installer Mode/Edit All Codes
Option 4 - User can Change Telephone Numbers
Option 5 - User can Change Clock Settings
Option 6 - User can Change DTMF Codes
Option 7 - User can Learn New Radio Devices
Option 8 - User can Force a Download to the Call-back Number
Option 1 User can Change Their Code - If a User has option 1 on, they can access Client Program Mode and
change their code number.
Option 2 User can Change All Codes - If a User has option 2 on, they can access Client Program Mode and
change All User code numbers.
Option 3 User can Allow access to Installer Mode/Edit All Codes - If a User has option 3 on, they can access
Client program Mode. From there an Installer with the correct Installer Code can access Installer
Program Mode. The User with this option can also edit all User Codes and associated parameters as
shown in the chart on page 112.
Option 4 User can Change Telephone Numbers - If a User has option 4 on, they can access Client Program Mode
and change the telephone and call divert numbers.
Option 5 User can Change Clock Settings - If a User has option 5 on, they can access Client Program Mode and
change the Time & date settings as well as daylight saving sart and finish times.
Option 6 User can Change DTMF Codes - If a User has option 6 on, they can access Client Program Mode and
change the DTMF Codes. A DTMF Code can be used to remotely Arm/Disarm an Area, turn Output/s On/
Off or Acknowledge a Voice/Domestic alarm.
Option 7 User can Learn New Radio Devices - If a User has option 7 on, they can access Client Program Mode
and Learn a new Radio Key or Wireless Zone Device. They can also remove radio devices or find what
location number a device is stored at.
Option 8 User can Force a Download to the Call-back Number - If a User has option 8 on, they can access Client
Program Mode and force a PC connection to a pre-defined call-back number. They can either enter in
P200E12E or if using an LCD keypad go to the "Diagnostics" Menu and select "Start Callback".
RADIO USER TYPE - P7E 21-100E (NOTE: only Users 21-100 can be Radio Users)
Option 0 - Generic (General Pendant Type)
Option 1 - Crow Freelink Pendant

USER CODE PRIVILEGES

RADIO USER TYPE

40