Contact Id Reporting Code Summary - Assa Abloy S series Installation & Programming Manual

In addition to the programmable Contact ID Event Code assignments defined at P157E, P158E, P159E, P175E (10E-12E) there are a
number of fixed event codes. The programmable and fixed event codes are all listed in the table below. Associated with the fixed and
programmable event codes, there are a number of extension codes, that are also listed below. The list of extension codes is for your
reference only and can not be changed in programming.
Event Type
System Tamper
Zone Alarm (wired or wireless)
Zone Tamper - Low (short circuit)
Zone Tamper - High (open circuit)
Zone Tamper - Radio Zone
Zone Near Alarm
Zone Confirmed Alarm
Radio PIR / Reed Switch Battery Low
Radio PIR Supervised Alarm
Sensor-watch Alarm
Zone Excludes
Keypad Panic (or 1&3)
Radio-Key Panic
Keypad Fire (4&6)
Keypad Medical (7&9)
Keypad Tamper Switch Alarm
Wrong Code Alarm
Arm/Disarm by "ARM key (Quick Arm)
Arm/Disarm by user code
Arm/Disarm by Radio-key
Arm/Disarm by Key-switch
Arm/Disarm by DTMF or Up/Download
Arm/Disarm by Time-Zone
Latchkey Disarm
Fail to Arm on Time-Zone
Delinquency Alarm
Stay Mode Arm/Disarm (part set)
Stay Mode Arm/Disarm (part set)
Stay Mode Arm/Disarm by Key-switch
Stay Mode Arm/Disarm by Key-switch
Mains Fail
System Battery Low
Checksum Fail (Corrupt EEPROM Data)
Fuse Fail
Radio-key Battery Low
Radio-PIR / Reed Switch Battery Low
Automatic TEST Calls
Manual TEST Calls
Phone Line Failure
Duress Alarm
Program Mode Entry
Program Mode Exit
Output 1 or 2 Tamper
Time & Date Changed
Keypad Bus Trouble
RF Receiver jam detected
Dialler Failure
Listen-In Request

Contact ID Reporting Code Summary

Event Code
137
130
383
383
383
138
139
384
381
391
570
120
120
110
100
137
461
408
401
400
409
409
407
403
642
455
454
441
441
442
442
301
302
303
312
384
384
602
601
351
121
627
628
323
625
330
344
354
606
Extension Comment
000 Panel & Sat Tamper etc
001 to 016 Alarm on Zone 1-16
001 to 008 Zone Input 1-8 short circuit
009 to 016 Zone Input 1-8 open circuit
001 to 016 Radio Zone 1-16
001 to 016 Zone Input 1-16
001 to 016 Zone Input 1-16
001 to 016 Radio Zone 1-16
001 to 016 Supervised Radio Zone 1-16
001 to 016 Zone 1-16
001 to 016 Exclude Zone 1-16
001 to 008 Panic at keypad #1-8
021 to 100 Panic by Radio User # 21-100
001 to 008 Fire Alarm at keypad #1-8
001 to 008 Medical Alarm at keypad #1-8
101 to 108 Keypad 1-8 Tamper Switch Activated
001 to 008 4 Incorrect code entries at KP # 1-8
000 Arm/Disarm by single button
001 to 100 Arm/Disarm by User #1-100
021 to 100 Arm/Disarm by Radio User #21-100
000 Key-switch # 1 Arm/Disarm
001 Key-switch # 2 Arm/Disarm
000 Remote Arm/Disarm
000 Time-Zone Arm/Disarm
001 to 100 Latchkey User Disarm
000 Auto Arm fail
000 System not Armed within # days
000 Arm by "Stay" Button
001 to 100 Stay Mode Arm by User # 1-100
000 Stay Mode Arm by Key-switch # 1
001 Stay Mode Arm by Key-switch # 2
000 Mains (AC) fail
000 Control Panel Battery low
001-008 Checksum block error
000 Fuse 1 or 2 Fail
021 to 100 Radio-key User #21-100 low batt.
001 to 016 Radio Zone 1-16
000 24 hour test
000 User generated Test Call
000 Reported when line is restored
001 to 008 Duress at Keypad #1-8
000 Program Mode entered
000 Program Mode exited
001 or 002 O/P 1 or 2 wires cut.
000 Time & Date has been changed
001 to 008 Keypad device 1-8 offline
000 RF Jamming Detected
000 Failure to get kiss off
000 Hold line open after alarm
116