Area Delinquency Time; Auto-Arm/Disarm Time-Zone; Keypads; Keypad Area Assignment - Assa Abloy S series Installation & Programming Manual

AUTOMATIC ARM/DISARM TIMEZONE - P68E 1-2E (1 = Area A, 2 = Area B) (Value 1-8)
Option 1 - Time-Zone 1
Option 2 - Time-Zone 2
Option 3 - Time-Zone 3
Option 4 - Time-Zone 4
If Option 2 or 3 are turned on location P46E then the Area can be automatically armed or disarmed by a time-zone/s. You
can assign more than one time-zone to each Area. If assigning multiple time-zones you should insure that they do not
overlap as this could cause confusion. A Time-zone would typically be 0830-1700 Monday-Friday. An area will turn on
when the Time-zone ends (eg 1700) and turn off when a Time-zone starts (eg 0830)
KEYPAD AREA ASSIGNMENT - P71E 1-8E
Option 1 - Area "A"
Option 2 - Area "B"
Option 1 Area "A" - This option assigns Area A to keypads. If a keypad is assigned to only Area A it can only Arm or
Disarm that area.
Option 2 Area "B" - This option assigns Area B to keypads. If a keypad is assigned to only Area B it can only Arm or
Disarm that area.
KEYPAD BUTTON OPTIONS - P72E 1-8E
Option 1 - <CHIME> or <CONTROL><PROGRAM> button Enabled
Option 2 - <BYPASS> button Enabled
Option 3 - <PANIC> button Enabled
Option 4 - Delayed Operation of <PANIC> button
Option 5 - <1> + <3> or <CONTROL> + <CHIME> Panic Alarm Enabled
Option 6 - <4> + <6> or <A> + <B> Fire Alarm Enabled
Option 7 - <7> + <9> or <B> + <CHIME> Medical Alarm Enabled
Option 8 - Stay Armed Beep to Keypad
Option 1 <CHIME> or <CONTROL><PROGRAM> button Enabled - This option enables the <CHIME> button on the
Landscape LCD keypads or the <CONTROL> followed by the <PROGRAM> button on the LED and Portrait
LCD keypads. Chime alarms to the keypad buzzer and outputs are disabled when "Chime" is off. If a zone is
programmed as a Chime Zone, it can beep the buzzer on a keypad and/or turn on an output as well to give a
local "CHIME" indication. A typical use of "Chime" Mode is as a door minder in a shop. Sometimes it may be
desirable to disable Chime mode without the need to reprogram the panel. This can be achieved by
allowing Chime Mode to be disabled with the <CHIME> button on a Landscape LCD keypad, or by using the
<CONTROL> and <PROGRAM> buttons on an LED or Portrait LCD keypad. If you press the <CHIME> button
on a Landscape LCD keypad for 2 seconds (and this option is turned on for that keypad) the display will
show "Chime Mode OFF". This means that the buzzer will now not sound at the keypad concerned and any
Chime Mode Outputs will not activate. Pressing the <CHIME> button again for 2 seconds will toggle chime
mode back to on again. If using an LED or Portrait LCD keypad (which do not have a dedicated chime
button), you simply press and hold the <CONTROL> Button and within 2 seconds then press the
<PROGRAM> button to toggle chime mode. The Portrait LCD keypad will show "Chime Mode OFF' and the
LED keypad will turn on the "AUX(0)" Led to show that chime mode is off. Performing the process again will
toggle chime mode back to the on state again.
Option 2 <BYPASS> button Enabled - This option enables the <BYPASS> button (by keypad number) on any
keypads connected to the panel .
AUTOMATIC ARM/DISARM TIMEZONE

KEYPADS

KEYPAD AREA ASSIGNMENT

Option 5 - Time-Zone 5
Option 6 - Time-Zone 6
Option 7 - Time-Zone 7
Option 8 - Time-Zone 8
KEYPAD BUTTON OPTIONS
58