Lcd Program Menus; Lcd Keypad Menu Programming - Assa Abloy S series Installation & Programming Manual

The LCD Keypad enables "Manual Free' programming of the
will be displayed on the keypad to enable selection of the desired programming options.
ENTER
PROGRAM
<Up> or <Down> arrow keys will allow you to cycle through the Menu options (Main & Sub Menus).
<Left> or <Right> arrow keys can be used when in the Data Entry-Menus to cycle through the
options (eg if in "USERS" Data Entry-Menu, the options would be Users 1-100, if in "ZONES" the
options would Zones 1-16, etc)
SELECTING THE MAIN-MENU HEADINGS ("
Enter "INSTALLER" Program Mode eg <PROGRAM> - <INSTALLER CODE (000000)> - <ENTER>.
The LCD will display "INSTALLER:USERS". This is the default Main-Menu heading.
To access a desired program location you first navigate to the desired Main-Menu by using the "
arrow keys on the keypad. Each press of "
heading.
The Main-Menu headings are shown on the top line of the LCD display.
To access the Sub-Menu options from a Main-Menu press the <ENTER> button.
SELECTING THE SUB-MENU HEADINGS ("
Having pressed the <ENTER> button at the selected Main-Menu heading the keypad will now show Sub-Menus for that
heading. The Main-Menu heading will remain on the top line of the LCD display and the Sub-Menus will appear on the
bottom line. Each press of "
either up or down by one location.
To access the Data Entry-Menu options from the Sub-Menu press the <ENTER> button.
SELECTING THE DATA ENTRY-MENU HEADINGS
Having pressed the <ENTER> button at the desired Sub-Menu heading, the keypad will now be in the Data Entry-Mode.
The Main-Menu heading on the top line of the display will be replaced with the actual data entry field description, eg if
you had gone from "USERS" to "CODES" then to the data entry field of codes the display will show "USER CODE 1" on the
top line of the display and the code "123" on the bottom line ("123" being the default User 1 code). See the chart on
page 21 for details.
You can now change the code, eg to change Code # 1 to 4567 press <4567> <ENTER>. The bottom line will now show
the new code of "4567".
At this point you can use the "
Code 1 to program all of the options for code 1, or;
You can use the " Left" or "
the user codes from 1-100. The "
arrow key will take you down one User, eg if the display was currently showing "USER CODE 10", pressing the "
arrow key will take the display to "USER CODE 9", pressing the "
11". You can also use the "
User, you can also use the "
If you are at a location that has 8 programmable options, eg P4E where the User Arm/Disarm options can be set, by press-

LCD KEYPAD MENU PROGRAMMING

<ENTER> key selects the Menu you wish to work in or the option in a Sub-Menu you wish to
use.
<PROGRAM> key will step you back to the previous Menu level.
Up" or "
Up" or "
Up" or "
Up" or " Down" arrow keys will advance the Sub-Menus displayed on the bottom line
Up" or " Down" arrow keys to cycle through the other Sub-Menu options for User
Right" arrow keys to cycle through all of the User codes. This allows you to program all of
Right" arrow key when pressed will take you up one User at a time and the "
Left" or " Right" arrow keys to move through all of the User codes, and while at a particular
Up" or " Down" arrow keys to program all options for that User.
'S series' panel. Easy to follow plain text Menus
Down" Arrow Keys)
Down" arrow keys will advance the display to the next Menu
Down" Arrow Keys)
Right" arrow key will take the display to "USER CODE
30
Up" or " Down"
Left"
Left"