Vandal resistant weatherproof digital keypad (13 pages)
Summary of Contents for Assa Abloy Yale Assure Lever YRL216
Page 1
Yale Assure Lever ® Keypad (YRL216) and Key-Free Keypad (YRL236) Installation and Programming Instructions #8-32 x 5/16" Machine screws #7 wood & #8-32 machine x 20mm M4 x 22mm Combination screws Pan head machine screws Levers Let's Get Started Installation Guide Envelope Battery Cover (Includes this manual and door checker with template)
Preparing to Install Tools Needed Standard Phillips Head Screwdriver Tools necessary only for new doors or adjusting existing prep. Tape Pencil Measure Drill Wood Mortise Utility Knife Level Chisel P/N YRL-PB-MNL-0017 Rev A...
Page 3
Check Door Measurements and Make Adjustments If Needed Door Checker Use door checker from installation guide envelope to verify your door measurements and make any needed adjustments. Check Your Door Guide Let's Get Started New Door Marking Template With door checker, use template from installation guide envelope to prep a new door that has not been predrilled for hardware.
Page 4
Determining Door Handing Inswinging Door Outswinging Door Interior Left Hand Right Hand Interior Reverse Reverse Left Hand Right Hand Exterior Exterior Face a door swinging open Face a door swinging open away from you. toward you. If it swings open to the right, If it swings open to the right, it it is a right hand door.
Page 5
Preparing Door & Frame Necessary for new doors or adjusting existing prep. 2-1/8" Door Prep (54mm) Template Dia. 2-3/8" (60mm) 1" (25mm) 2-3/4" (70mm) Dia. Backset Drill holes 1/2 way through door then complete from other side to prevent splitting. Frame Frame Inside...
Page 6
Installing Latch & Strike Plate Right Hand Installation Shown 2-3/8" through bolt posts default PULL 2-3/4" through bolt posts Note: Adjustment based on backset optional Outside of Door Frame *Backset *2-3/8" (60mm) 2-3/4" (70mm) P/N YRL-PB-MNL-0017 Rev A...
Page 7
Installing Keypad Right Hand Installation Shown “TOP” mark must be on top surface and tailpiece in vertical position. Incorrect orientation will cause lock to fail. Outside of Right Hand Door Inside of Right Hand Door P/N YRL-PB-MNL-0017 Rev A...
Page 8
Installing Interior Mounting Plate Right Hand Installation Shown Inside of Right Hand Door Inside of Right Hand Door P/N YRL-PB-MNL-0017 Rev A...
Page 9
Attaching the Cable Assembly Right Hand Installation Shown Ensure cable is securely fastened into adapter. Inside of Right Hand Door Use cable hooks for proper cable routing. P/N YRL-PB-MNL-0017 Rev A...
Page 10
Installing Interior Lock Right Hand Installation Shown Inside of Right Hand Door “Click” P/N YRL-PB-MNL-0017 Rev A...
Page 11
Installing Exterior Cylinder (YRL216) or Key-Free Cylinder (YRL236) YRL216 Cylinder YRL236 Key-Free Cylinder Remove key from cylinder. There is no key. Outside of Right Hand Door Cylinder Tailpiece (YRL216) must slide into vertical slot Cylinder must be installed Latch with bar away from latch. Tailpiece Cylinder (YRL216)
Page 12
Installing Exterior Lever Outside of Right Hand Door YRL216 Cylinder Shown Press pin while installing lever so lock is not damaged. Installing Interior Lever Inside of Right Hand Door Press pin while installing lever so lock is not damaged. P/N YRL-PB-MNL-0017 Rev A...
Page 13
Testing Thumbturn Operation Test with door open. Outside of Right Hand Door Outside of Right Hand Door Test thumbturn and both levers in locked and unlocked positions. If operation fails, check installation beginning with Step 2 and refer to Hardware Troubleshooting. P/N YRL-PB-MNL-0017 Rev A...
Page 14
Testing Key Operation (YRL216) Test with door open. Outside of Right Hand Door Outside of Right Hand Door If key operation test fails, check installation beginning with Step 6. P/N YRL-PB-MNL-0017 Rev A...
Page 15
Installing Smart Module (if included) Inside of Right Hand Door Batteries must not be installed prior to inserting and/or removing module. NOTE: If a Smart module was included with your lock, it is in a separate box with additional module installation instructions.
Page 16
Installing Batteries & Cover Inside of Right Hand Door Congratulations, you've installed the Yale Assure Lever ® Keypad ( YRL216 ) or Key-Free Keypad (YRL236)! Using Your Lock instructions will help you customize your lock. P/N YRL-PB-MNL-0017 Rev A...
Page 17
Testing Keypad Operation Test with door open. A Master Entry Code must be created upon installation or after resetting the lock to factory default. Programming and use of lock is not possible until this step has been successfully completed. See of Using Your Lock instructions below.
Resetting Lock to Factory Default Interior Lock Reset Button When resetting the lock, all user codes, including the Master Entry Code*, are deleted. All programming features are reset to original default settings. See “Setting Definitions”. 1. Remove the battery cover and batteries. 2.
Hardware Troubleshooting Cycle lock in both the locked and unlocked positions. If problems are found: Tailpiece and spindle will not mate and fit into the interior escutcheon a. Ensure that your door is between 1-3/8" and 1-3/4" thick b. Ensure that the square shaped spindle has “Top” writing and arrow facing upwards c.
Setting Definitions Settings Default Setting Definition The Master Entry Code is used for programming and for feature settings. It must be created prior to Creation Master Entry Code required* programming the lock. The Master Code will also operate (unlock/lock) the lock. This feature is enabled by the Master Entry Code.
Page 21
Using Your Lock Keypad Low Battery Indicator Press any key (flashes red) to wake keypad All Code Lockout Mode (keypad flashes) Press to enter Speaker or unlock Enter Master Entry Code and press to access Settings Menu Battery Back-up* Hold a 9V battery to the terminals in case of dead lock batteries and no key Interior Lock...
Page 22
Creating Master Entry Code Creating a Master Entry Code must be performed upon installation or after resetting the lock to factory default. Programming and use of lock is not possible until this step has been successfully completed. Press Press Press Enter 4-8 digit Master Entry Code...
Page 23
Creating Entry Codes Master Entry Code must be created first. *Max Entry Codes = 250 with Smart Module and 25 without. Enter Master Entry Code Press Press Enter 4-8 digit Entry Code Press Press Press Press (code flashes) Adding more Entry Codes: To end programming: Press Press...
Page 24
Deleting Entry Codes Enter Master Entry Code Press Press Press Press Press Deleting one Entry Code: To delete all Entry Codes (Does not delete To delete one Entry Code, Master Entry Code): you must enter the Entry Code you wish to delete. Enter 4-8 digit Entry Code Enter Press...
Unlocking Door with Entry Code Enter Entry Code Press Code Chart Duplicate if necessary Entry Code Management Entry Code Homeowner Master: Babysitter User Name: P/N YRL-PB-MNL-0017 Rev A...
Page 26
Customizing Lock Through Settings Menu *Master Entry Code Required 1. Press any key to wake lock. 2. Enter Master Entry Code* followed by icon. 3. Enter digit corresponding to the function to be performed followed by the icon. Advanced Auto Re-lock Disable Lock Settings 30 sec...
Programming Troubleshooting Symptom Suggested Action Check that keypad cable assembly is fully connected and not pinched. Check that the cable is firmly connected to the interior lock. Entry Codes must consist of 4 to 8 digits. Entry Code has already been added or maximum number of codes has been reached.
Page 28
Ÿ Consult the dealer or an experienced radio/TV technician for help. Ÿ Warning: Changes or modifications to this device, not expressly approved by ASSA ABLOY Residential Group could void the user's authority to operate the equipment. Industry Canada: This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.
Page 29
Yale Z-Wave Plus Smart Module ® ® ® Installation Guide Please use this procedure only when network primary controller is missing or otherwise inoperable. Adding a Yale Z-Wave Plus Smart Module to your Assure Lock & Z-Wave System ® 1. Install the Yale Smart Module into the slot above the battery compartment IMPORTANT: The batteries must be removed before removing the Yale Smart Module: •...
Page 30
24/7 Tech Support : 1-855-492-0505 • www.yalehome.com Yale® is a registered trademark of ASSA ABLOY Residential Group. Other products' brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only.
Page 31
Yale ZigBee Module ® ® ® Installation and Programming Instructions Installing the ZigBee Module ® IMPORTANT: the batteries must be removed prior to removing and/or inserting the network module: • Remove battery cover. • Remove batteries. • Remove and/or insert network module. •...
Page 32
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company. Yale® and Yale Real Living® are registered trademarks of Yale Security Inc., an ASSA ABLOY Group Company. Other products’ brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only.
Need help?
Do you have a question about the Yale Assure Lever YRL216 and is the answer not in the manual?
Questions and answers