Telephone Number Report Options - Assa Abloy S series Installation & Programming Manual

8/16 zone control communicator

page of 119

/ 119
Contents
Table of Contents
Bookmarks

Table of Contents

Option 6

4 + 2 (10 pps) - This option transmits a 4 digit account code followed by a 2 digit event code to a central

monitoring station. The handshake tone from the monitoring station must be 2300hz and the transmit tone

from the panel will be at 1800hz at 10 pulses per second.

Option 7

4 + 2 (20 pps) - This option transmits a 4 digit account code followed by a 2 digit event code to a central

monitoring station. The handshake tone from the monitoring station must be 1400hz and the transmit tone

from the panel will be at 1900hz at 20 pulses per second.

Option 8

4 + 2 (20 pps) - This option transmits a 4 digit account code followed by a 2 digit event code to a central

LED KEYPAD

BUTTON

INDICATION

"BYPASS"

"PANIC"

"MEMORY"

"CONTROL"

"ARM"

"STAY"

monitoring station. The handshake tone from the monitoring station must be 2300hz and the transmit tone

from the panel will be at 1800hz at 20 pulses per second

Option 9

4 + 2 (DTMF) - This option transmits a 4 digit account code followed by a 2 digit event code plus a

checksum using DTMF signals to a central monitoring station. The handshake tone from the monitoring

station must be 1400 hz /2300 hz .

Option 10

SIA - This option selects FSK SIA format. If using SIA format, ensure that the monitoring receiver does not

generate a 4+2 2300hz acknowledge tone before the SIA acknowledge tone because the 4+2 tone accuracy

is +/– 5% which can make it the same as the SIA acknowledge tone. Also when reporting alarms on different

areas (1 =Area A and 2 = Area B) the panel will send the area number associated with each event (ri01 or

ri02) but it will also send different account codes if programmed that way. To avoid using two account

numbers when reporting alarms on different areas you should program both account codes (P62E 1 & 2) to

be the same number and identifying the two areas by the area number sent.

Option 11

SIA Slow - This option selects FSK SIA Slow format. This format is similar to option 10 except every signal will

be sent separately with a kissoff after each signal whereas option 10 will send all signals in one continuous

burst with one kissoff at the end. In SIA slow the area number is not sent (see option 10 above) so each

account code must be different when identifying alarms for both areas.

TELEPHONE NUMBER REPORT OPTIONS - P183E 1-8E

Option 1 - Stop Dialling if Kissed Off

Option 2 - Monitor Call Progress

Option 3 - Blind Dial

Option 4 - Use Group Numbers for Contact ID Reporting

Option 5 - Stay On-line after Alarm report for two way voice

Option 6 - Auto Kiss-off for Voice/Domestic Reporting

Option 7 - Use the Dial Pre-fix Number

Option 8 - Used as the Call-back Number

Option 1

Stop if Kissed Off - If this option is turned on for the telephone number, the dialler will stop sending the

alarm if the signal is kissed off and will not proceed with any other telephone numbers for that event. If not

kissed off the dialler will start dialling any other programmed numbers. If the event is not kissed off from any

of the telephone numbers and the maximum re-tries limit is reached then the event is marked as unsent

and will be added to the next event that causes the dialler to report. If this option is off, the dialler will send

LCD KEYPAD

BUTTON

CONTROL & 0

CONTROL & 2

CONTROL & 3

CONTROL & 4

CONTROL & 5

CONTROL & 6