System Configurations - Xerox Phaser 8860 Service Manual

System Configurations

Standard Features
The Phaser 8860/8860MFP offers these standard features:
• Maximum print speed (pages per minute) based on letter-size plain paper:
NOTE: Print speeds for media fed from Tray 1 may be up to 50% slower.
Table 1 Phaser 8860/8860MFP Print Speeds
Phaser 8860 Color Printer
PostScript Print Quality Modes:
– Fast Color: 30 ppm
– Standard: 24 ppm
– Enhanced: 16 ppm
– High Resolution/Photo: 10 ppm
PCL Print Quality Modes:
– 300 x 600 dpi: 16 ppm
– 600 x 600 dpi: 8 ppm
• First-page-out: 6 seconds for color prints, 15 seconds for color copies
• Copy, Print, Scan, Fax capabilities (options vary according to configuration and memory)
• Connections: USB, Ethernet 10/100 Base-Tx, Foreign Device Interface (available)
• RJ-11 Fax Modem (8860MFP only)
Available Configurations
Table 2 lists the standard configurations.
Table 2 Phaser 8860/8860MFP Configurations
Features
Memory
Hard Drive
Automatic 2-sided Printing (DADF)
525-Sheet Feeder
System Cart
Copy
Scan to PC
Scan to E-mail
Scan to Hard Drive
Fax
* This option can be purchased separately for this configuration.
Product Options
Phaser 8860/8860MFP options include:
• Additional Trays
Initial Issue
Phaser 8860/8860MFP Service Manual
Phaser 8860MFP Multifunction Product
PostScript Print Quality Modes:
– Fast Color: 30 ppm
– Standard: 24 ppm
– Enhanced: 16 ppm
– High Resolution/Photo: 10 ppm
PCL Print Quality Modes:
– 300 x 600 dpi: 16 ppm
– 600 x 600 dpi: 8 ppm
8860 8860MFP
256 MB 512 MB
No* Yes
No Yes
No* No*
No* No*
No Yes
No Yes
No Yes
No Yes
No Yes
• Memory
• System Cart
Additional Trays
Trays 1 and 2 are standard on all configurations. The following additional tray combinations are
supported:
• One 525-Sheet Feeder (Tray 3)
• Two 525-Sheet Feeders (Trays 3 and 4)
Memory
All configurations have two memory slots supporting 256 MB, 512 MB, and 1 GB SODIMM
modules (up to maximum of 1 GB DDR2).
System Cart
The System Cart supports a fully-optioned system and provides space for media storage.
Metered Printing
Metered printing (PagePack), involves the combination of control software and specialized Ink
Sticks to meter system activity for billing purposes. The Configuration page lists Metered Ink as
Enabled when metering is enabled.
Metered Operation
When a metered printer is initialized at first power-up, the customer sets the printer to Metered
operation using a unique, factory-supplied, 4-digit PIN. Once set to Metered operation, the con-
trol software performs the following:
1. The Mode and PIN-entered values in Engine Control Board NVRAM are set.
2. The Control Panel momentarily displays "Metered Ink is now enabled", then returns to
"Ready" (if no other errors).
3. The First Time Tips pages and the Configuration page are printed.
If an incorrect PIN is entered, "Incorrect numeric password" displays with a prompt "Retry" or
"Do not retry." Retry returns to the enter prompt, "Do not retry" returns to the Replace Ink Stick
error message. The error persists until the correct PIN is entered.
NOTE: The Hidden Service menu provides an Enable Metered Ink option to restore the
Metered mode parameters to NVRAM should they become lost or corrupt.
Metered Ink
To support metered printing, metered Ink Sticks are available in all four colors. The shape of
the metered Ink Stick differs from the non-metered versions.
09/2007
xiii
Introduction
System Configurations