Xerox Phaser 8860 Service Manual page 89

Table 3 Jam Code Troubleshooting
Code Description / Procedure
N4A Y-Axis motor stalled on power-up following an abnormal shutdown.
N4B Y-Axis motor stalled on power-up following a normal shutdown.
N4C Y-Axis motor stalled during mechanical recovery
N4D Y-Axis motor stalled during warm-up.
NFE Y-Axis motor stalled during ready state.
N4F Y-Axis motor stalled during a fault state.
N4G Y-Axis motor stalled during an auto drum maintenance cycle.
N4H Y-Axis motor stalled during printhead maintenance.
N4J Y-Axis motor stalled during printhead purge.
N4K
Y-Axis motor stalled during an oil Transfix Roller cycle.
N4L Y-Axis motor stalled during standby mode.
N4S Y-Axis motor stalled during staging for transfix.
N4T Y-Axis motor stalled during transfixing.
N4V
Y-Axis motor stalled during a print drum maintenance cycle.
N4W Y-Axis motor stalled during drum imaging.
N4X Y-Axis motor stalled during paper exit.
1. Check for supported media, generally label, trifold or envelopes cause this error.
2. Try running fewer sheets through the tray.
3. Check that the Process Drive is correctly homed
4. Test theY-Axis Motor using Service Diagnostics, replace if necessary
4.0.11).
5. Test for Y-Axis Belt slippage using the Belt Slip test.
6. Replace the Tray 1 Separator Pad assembly.
7. Replace the Process Drive
N5T Y-Axis motor out of position during transfixing.
N5W Y-Axis motor out of position during drum imaging.
1. Check the Y-Axis drive belt.
2. Run the Check Drum Y-Axis Encoder test.
3. Run the Check Drum Y-Axis Drive test.
4. Test for Y-Axis Belt slippage using the Belt Slip test.
5. Replace the Y-Axis Motor (REP
sary.
N6T Y-Axis Motor media short during transfix. The media was shorter than expected. Legal
size paper from Tray 4 in standard print mode may buckle. Use slower print mode.
1. Check for supported media.
2. Check system grounds.
3. Run the Check Drum Y-Axis Encoder test.
4. Remove the Preheater (REP
paper interference.
5. Replace the Preheater (REP
Initial Issue
Phaser 8860/8860MFP Service Manual
(ADJ 4.7.1).
(REP 4.0.7).
4.0.11), or Drum Assembly (REP 2.0.3) if neces-
2.0.17), and check the Preheater flag for ink or
2.0.17).
Code Description / Procedure
N7T Y-Axis Motor media long during transfix. The media was longer than expected.
1. Check for supported media.
2. Try heavier media.
3. Try loading only a few sheets. Some photo media may require running one sheet
at a time.
4. Run the diagnostic Check Drum Y-Axis Encoder test.
5. Replace the Pick Assembly and Retard Roller
6. Run the clean ink smears and check the Preheater exit flag for debris.
7. Remove the Preheater
paper interference.
8. Replace the Preheater
P4A Process Drive stalled on power-up following an abnormal shutdown.
P4B Process Drive stalled on power-up following a normal shutdown.
P4C Process Drive stalled during mechanical recovery
P4D Process Drive stalled during warm-up.
PFE Process Drive stalled during ready state.
P4F Process Drive stalled during a fault state.
P4G Process Drive stalled during an auto drum maintenance cycle.
(REP P4H Process Drive stalled during printhead maintenance.
P4J Process Drive stalled during printhead purge.
P4K Process Drive stalled during an oil Transfix Roller cycle.
P4L Process Drive stalled during standby mode.
P4S Process Drive stalled during staging for transfix.
P4T Process Drive stalled during transfixing.
P4V Process Drive stalled during a print drum maintenance cycle.
P4W Process Drive stalled during drum imaging.
P4X Process Drive stalled during paper exit.
1. Check for supported media.
2. Check that the Process Drive is correctly homed
3. Test the Process Drive using Service Diagnostics.
4. Replace the Process Drive
5. Run the Transfix Fast and Slow tests.
6. Replace the Transfix Camshaft
7. Run the Tilt Drive test, replace if necessary.
8. Replace the Process Drive
09/2007
2-57
Table 3 Jam Code Troubleshooting
(REP 3.0.18).
(REP 2.0.17), and check the Preheater flag for ink or
(REP 2.0.17) if the error persists.
(ADJ 4.7.1).
(REP 4.0.7) if necessary.
(REP 2.0.10) and load arms if necessary.
(REP 4.0.7).
Error Messages and Codes
Jam Codes