Connect The Power Cord - Nikon Eclipse Ni-E Instruction Manual

CONTACT ARM2
(Connect to CONTACT ARM2 of Ni-E
main body)
CONTACT ARM2
(Connect to CONTACT ARM2 of
contact arm)
DSC2
(Connect to EXT.I/O of
DS-L3/U3)
ERGO/JOY
(Connect to ergo controller
or
joystick controller)
ND
(Connect to motorized ND
filter wheel)
(Connect to Ni-E for control box A)
HGFIE
(Connect to motorized HG
precentered fiber illuminator
RS-232C)
CAMERA
(Connect to camera head)
EXT.I/O
(Connect to DSC1 of Ni-E
main body or DSC2 of
connector box)
DS-L3 DS camera control unit
26

Connect the power cord

(1) Check that the power switch for control box A is off
(press the switch to the "O" position).
(2) Plug the power cord into the AC inlet on control box A.
(3) Plug the other end of the power cord into a wall outlet.
Connecting the power cord to the connected motorized unit
Check that the power to the connected device such as a DS camera control unit, etc. is turned off, plug the
power cord into the AC inlet, and then plug the other end to the wall outlet.
Chapter 1
CONTACT ARM2
USB
DSC1
1.
HGFIE
2.
BOX
3.
BOX
Ni-E (Rear)
USB(H)
(Connect to USB at rear
of Ni-E main body)
Input voltage label
Assembly
EPI SHUTTER
MODEL ECLIPSE Ni-E
NIKON CORPORATION
TOKYO, JAPAN 9 1 0 0 0 1
M A D E I N J A P A N
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est confirme à la norme NMB-003 du Canada.
CAUTION!
-High Temperature-
Do not touch the lamphouse while the lamp is lit.
The surface of the lamphouse becomes hot when the
lamp is on.
Turn off the power and allow the lamp and lamohouse
to cool enough before replacing the lamp.
Wait for at least 30 minutes after turning off the
lamp.
Use 12V100W HALOGEN lamp only.
HALOGEN 12V100W
NI-LH
JAPAN
9 5 2 0 0 1
Ni-E (Connect to BOX of Ni-E)
OFF ON
FASTENING
N i - E POSITION SW CONTACT
This device complies with Part
15 of the FCC Rules. Operation
is subject to the following
two conditions:
(1) this device may not cause
harmful interference, and
(2) this device must accept any
interference received,
including interference that
may cause undesired
operation.
This Class A digital apparatus
complies with Canadian ICES-003.
Cet appareil numérique de la
classe A est confirme à la
norme NMB-003 du Canada.
MODEL NI-CTLA
5 4 0 0 0 1
MADE IN JAPAN
100-240V~ 5A 50/60Hz
Control box A (Rear)
35
CONTACT ARM1
(Connect to CONTACT ARM1 of
control box A)
EPI SHUTTER
(Connect to EPI motorized
shutter)
EX
(Connect to motorized
excitation filter wheel)
STAGE
(Connect to MICROSCOPE for
the motorized XY stage controller)
DIA SHUTTER
(Connect to DIA motorized
shutter)
USB
(Connect to the USB (H) for
DS-L3 or PC)
DSC1
(Connect to EXT.I/O of DS-L3/U3)
Fastening position mode
switch
(ON: fastening position mode,
OFF: normal mode)
ARM1
CONTACT ARM1
(Connect to CONTACT ARM1
of contact arm)
AC inlet
(Connect to AC power using a
LAMP
power cord)
LAMP
(Connect to dia-illumination
lamphouse)