SMC Networks HRS012-A*-10-* Operation Manual page 144

HRX-OM-M090
Chapter 8 Documents
Model
Cooling method
Refrigerant
Control method
Ambient temperature and humidity
Circulating fluid
Operating temperature
∗ 2
range
∗ 4
Cooling capacity
(50/60Hz)
∗ 6
Temperature stability
∗ 7
Pump capacity
(50/60Hz)
∗ 8
Rated fiow (50/60Hz)
Tank capacity
Port size
Wetted material
Temperature range
Pressure range
∗ 13
Required flow
Facility water pressure
differential
Port size
Wetted material
Feed water pressure
range
Feed water temperature
range
Feed water capacity
Automatic fluid filling Port size
Over flow port Port size
Power supply
∗ 17
Circuit protector
Applicable earth leakage
∗ 9
breaker capacity
∗ 4
Rated operating current
(50/60Hz)
Rated power
∗ 4
consumption (50/60Hz)
∗ 10
Noise level (50/60Hz)
∗ 11
Dimensions
Accessory
∗ 12
Weight
∗1
For water -cooled type.
∗2
Use the product in conditions where freezing will not occur.
Consult with SMC if using in a season or region where the ambient temperature will fall below zero.
∗3
If tap water is used, use water which satisfies the standard of The Japan Refregeration And Air Conditioning Industry Association (JRA
GL-02-1994/Cooling water system - circulation type - make-up water)
∗4 (1)Operating ambient temp.: 25°C, (2)Circulating fluid temp.: 20°C, (3)Circulating fluid rated flow, (4)Criculating fluid : Tap water,(5)Facility water
temp.: 25°C.
The cooling capacity will be reduced by 300W when option T and MT [High head pump] are selected.
∗5
Use a 15% ethylene glycol aqueous solution if operating in a place where the circulating fluid temp. is lower than 10
∗6
Outlet temp. when the circulating fluid flow is rated flow, and the circulating fluid outlet and the return are directly connected. Installation
environment and power supply are within specification range and stable.
∗7
The capacity at the thermo-chiller outlet when the circulating fluid temp. is 20°C.
∗8
Fluid flow to maintain the cooling capacity and the temperature stability.
The specification of the coolong capacity and the temperature stability may not be satisfied if the flow rate is lower than the rated flow.
∗9 To be prepared by the customer. Use an earth leakage breaker with sensitivity of 30mA/200V in power supply specification..
∗10 Front 1m/Height 1m/Static with no load. See note 3 for other conditions.
∗11 Dimension between panels. Projection is not included.
∗12 Weight when the circulating fluid and facility water (for water-cooled type) is not included.
The weight will increase by 1kg when option J [Automatic fluid filling] is selectedThe weight will increase by 6kg when option T and MT [High head
pump] are selected.
∗13 There is required flow when adding load described on cooling capacity in case of note4 conditions.
∗14 For option J [Automatic fluid filling port].
∗15 Copper, bronze and brass are not included when option M [DI water piping] is selected
∗16 This fitting is not included when option T and MT [High head pump] are selected.
∗17
If option "Earth leakage breaker type" is selected, the earth leakage breaker is used instead of the circuit protector.
∗18
The operating ambient temperature is 5 to 45°C for option G [High temperature type].
8.1 Specifications List
8-2
Table 8-2 Specifications List [HRS ∗∗∗ - ∗∗ -20-（BGJMT）]
HRS012-A∗
-20-（BGJMT） -20-（BGJMT）
Air-Cooled Water-Cooled
refrigerated
type
∗ 2
∗ 3
℃
W 1100/1300
℃
MPa
L/min
L
∗ 15,
Brass
-
℃
MPa -
L/min -
MPa -
MPa
℃
L/min
1-phase AC200 to 230V 50/60Hz. Allowable voltage range ±10%
A
A
4.6/5.1
A
For option -T，-MT : 5.6/6.7
0.9/1.0
kVA
For option -T，-MT : 1.1/1.3
dB
mm
Fitting (for drain port) 1pc., Sequence I/O command
signal connector 1pc., Power supply connector 1pc., Operation manual (Installatio･Operation ) 1pc,
Quick manual (with a clear cover) 1pc., Alarm code list label 1pc.
kg
HRS012-W∗ HRS018-A∗
-20-（BGJMT）
Air-Cooled
refrigerated refrigerated
type type
R407C(HFC),
PID control
Temperature ：5 to 40℃
Tap water, Ethylene glycol aqueous solution 15%
5 to 40
1700/1900
±0.1
0.13(at 7L/min)/0.18(at 7L/min)
For option -T：0.44(at 10L/min)/0.40(at 14L/min)
For option -MT：0.32(at 10L/min)/0.32(at 14L/min)
7/7
For option -T, -MT：10/14
Approx. 5
Rc1/2
Stainless steel, Copper brazing (Heat exchanger)
SIC, Aluminum oxide ceramic, Carbon, PP, PE, POM, FKM, EPDM, PVC
5 to 40 -
0.3 to 0.5 -
8 -
0.3 more -
Rc3/8
Stainless steel, Copper brazing, Bronze, Synthetic rubber
0.2 to 0.5
5 to 40
Approx.1
Rc3/8
Rc3/4
10（ For option -T，-MT : 15）
10（ For option -T，-MT : 15）
4.7/5.2
For option -T，-MT : 5.7/6.8
0.9/1.0
For option -T，-MT : 1.1/1.4
60/61
W377xD500xH615 (W14.8XD19.7xH24.2[Inch])
43
HRS018-W∗ HRS024-A∗
-20-（BGJMT） -20-（BGJMT）
Water-Cooled Air-Cooled
refrigerated refrigerated
type type
(GWP:1653)
∗ 18
、 Humidity：30 to 70%
∗ 5
2100/2400
∗ 15 ∗ 15
, Bronze
5 to 40 -
0.3 to 0.5 -
12 -
0.3 more -
For option -T，-MT : 6.1/7.5
For option -T，-MT : 1.2/1.5
o
C.
HRS024-W∗
-20-（BGJMT）
Water-Cooled
refrigerated
type
5 to 40
0.3 to 0.5
14
0.3 more
5.1/5.9
1.0/1.2
HRS Series