Water Ingress; Disclaimers; Chart Cards And Memory Cards; Emc Installation Guidelines - Raymarine a67 Wi-Fi Installation And Operation Instructions Manual

Water ingress

Water ingress disclaimer
Although the waterproof rating capacity of this product meets
the IPX6 standard, water intrusion and subsequent equipment
failure may occur if the product is subjected to commercial
high-pressure washing. Raymarine will not warrant products
subjected to high-pressure washing.

Disclaimers

This product (including the electronic charts) is intended to be
used only as an aid to navigation. It is designed to facilitate use
of official government charts, not replace them. Only official
government charts and notices to mariners contain all the
current information needed for safe navigation, and the captain
is responsible for their prudent use. It is the user's responsibility
to use official government charts, notices to mariners, caution
and proper navigational skill when operating this or any other
Raymarine product. This product supports electronic charts
provided by third party data suppliers which may be embedded
or stored on memory card. Use of such charts is subject to
the supplier's End-User Licence Agreement included in the
documentation for this product or supplied with the memory card
(as applicable).
Raymarine does not warrant that this product is error-free or that
it is compatible with products manufactured by any person or
entity other than Raymarine.
This product uses digital chart data, and electronic information
from the Global Positioning System (GPS) which may contain
errors. Raymarine does not warrant the accuracy of such
information and you are advised that errors in such information
may cause the product to malfunction. Raymarine is not
responsible for damages or injuries caused by your use or
inability to use the product, by the interaction of the product with
products manufactured by others, or by errors in chart data or
information utilized by the product and supplied by third parties.

Chart cards and memory cards

Memory cards are used for archiving data and chart cards
provide additional or upgraded charts.
Compatible cards
The following types of memory or chart card are compatible with
your Raymarine product:
• micro Secure Digital Standard-Capacity (microSDSC)
• micro Secure Digital High-Capacity (microSDHC)
Note: The maximum card capacity supported is 32 GB.
Chart cards
Your product is pre-loaded with electronic charts (worldwide
base map). If you wish to use different chart data, you can insert
compatible chart cards into the unit's card slot.
Use branded chart cards and memory cards
When archiving data, Raymarine recommends the use of quality
branded memory cards. Some brands of memory card may not
work in your unit. Please contact customer support for a list
of recommended cards.

EMC installation guidelines

Raymarine equipment and accessories conform to the
appropriate Electromagnetic Compatibility (EMC) regulations,
to minimize electromagnetic interference between equipment
and minimize the effect such interference could have on the
performance of your system
Correct installation is required to ensure that EMC performance
is not compromised.
For optimum EMC performance we recommend that wherever
possible:
10
• Raymarine equipment and cables connected to it are:
– At least 1 m (3 ft) from any equipment transmitting or
cables carrying radio signals e.g. VHF radios, cables and
antennas. In the case of SSB radios, the distance should
be increased to 7 ft (2 m).
– More than 2 m (7 ft) from the path of a radar beam. A
radar beam can normally be assumed to spread 20 degrees
above and below the radiating element.
• The product is supplied from a separate battery from that used
for engine start. This is important to prevent erratic behavior
and data loss which can occur if the engine start does not
have a separate battery.
• Raymarine specified cables are used.
• Cables are not cut or extended, unless doing so is detailed in
the installation manual.
Note: Where constraints on the installation prevent
any of the above recommendations, always ensure the
maximum possible separation between different items of
electrical equipment, to provide the best conditions for EMC
performance throughout the installation

RF exposure

This transmitter with its antenna is designed to comply with FCC
/ IC RF exposure limits for general population / uncontrolled
exposure. The WiFi / Bluetooth antenna is mounted behind the
front facia on the left hand side of the screen. It is recommended
to maintain a safe distance of at least 1 cm from the left hand
side of the screen.

FCC

Compliance Statement (Part 15.19)

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
FCC Interference Statement (Part
15.105 (b))
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
4. Consult the dealer or an experienced radio / TV technician
for help.
New a Series / New c Series / New e Series