Before Use; Notes On Handling The Internal Hdd; Notes On Installation Locations; The Hdd And Cooling Fan Are Consumable Components - Sanyo DSR-5016 Instruction Manual

1

BEFORE USE

Notes on handling the internal HDD

This digital video recorder uses an internal HDD.
Be sure to observe the following points carefully when
operating, setting-up, or servicing the digital video recorder.
Do not subject the digital video recorder to
sudden impact or vibration.
If the digital video recorder is subjected to sudden impact or
vibration, it may damage the hard disk or cause corruption of
the data stored within it.
Do not move the digital video recorder while the power is
turned on. Always ensure that the power is turned off
before removing the digital video recorder from or placing it
in a rack.
When transporting the digital video recorder, pack it
securely using the specified materials. In addition, choose
a method of transportation that minimizes vibration.
When placing the digital video recorder on the floor or
another similar surface, attach the specified pads to its
base and place it down gently.
Do not move the digital video recorder for 30
seconds after turning off the power.
After the power is turned off, the disk inside the HDD
continues to spin for a brief period due to inertia and the
heads are in an unstable condition.
During this period, the digital video recorder is even more
susceptible to damage from sudden impact and vibration than
when it is turned on. Make sure that the digital video recorder
is not subjected to even gentle vibration for at least 30
seconds after turning off the power.
Do not operate the digital video recorder when
condensation has formed on it.
If the digital video recorder is operated in this type of
condition, there is a possibility that it may become
permanently damaged.
If the temperature around the digital video recorder changes
suddenly, wait for it to stabilize before operating the digital
video recorder.
Notes on replacing the HDD
Be sure to follow the correct procedure when replacing the
HDD.
HDDs that have been removed from their packing may not
operate correctly if they are subjected to sudden impact or
vibration. It is recommended that you place the HDD on a
soft, level surface with the printed circuit board facing
upward after it has been unpacked.
Take care to avoid subjecting the HDD to sudden impact or
vibration when removing and tightening screws as part of
the HDD replacement procedure.
Tighten all screws securely to ensure that they do not
loosen.
The HDD is sensitive to static electricity; accordingly, you
should take the appropriate precautions to prevent the
buildup of static charges.
Handling a detached HDD unit
If transporting or storing the HDD unit in a detached condition,
be sure to first of all pack it using the specified materials.
In addition, choose a method of transportation that minimizes
vibration.
English

Notes on installation locations

Avoid subjecting the HDD to sudden impact or vibration. In
addition, avoid using it in dusty locations or near magnetic
objects. The following precautions should be observed in
order to prevent the loss of recorded data:
Do not subject the digital video recorder to sudden impact.
Do not use the digital video recorder on a vibrating or
unstable surface.
Do not disconnect the power plug from the wall outlet
during recording or playback.
Do not use the digital video recorder in areas with extreme
temperature changes (i.e., 10ºC or more per hour).
Condensation may occur if the digital video recorder is
moved to an area with a significantly different temperature
or high humidity. If the digital video recorder is used with
condensation inside, operating problems may occur.
Do not install the digital video recorder inside motor
vehicles, trains, or other areas with constant vibration.
The digital video recorder has ventilation holes on its left,
rear, and bottom panels. Ensure that these holes are not
blocked after installation.
Do not use the digital video recorder in a bookshelf, box, or
any other area with poor ventilation.
This digital video recorder is designed for use in a
horizontal orientation, and vertical setup may result in
malfunction.
When installing the digital video recorder in a rack, ensure
that a gap of at least 5 cm at the back and sides and 1 cm
at the top and bottom is provided.
The HDD and cooling fan are consumable
components.
If used in an ambient temperature of 25ºC, the HDD should
generally be replaced after two years, and the cooling fan
after three years. These figures are intended as a general
guideline only and should not be taken as a guarantee of
component performance.
The ERROR indicator flashes if a problem occurs with the
HDD or fan. ( P.17)

Important recordings

Always perform test recording in advance to confirm
whether the playback of the digital video recorder is
normal.
Note that Sanyo accepts no responsibility for losses
occurring as a result of recording or playback problems
caused by malfunction of this digital video recorder or any
connected devices.
As a precaution against malfunction or accidents, it is
advisable to periodically back up important recordings or to
perform mirroring.

Protection of the HDD

The HDD is checked automatically when the power is turned
on. If an abnormality is detected, the ERROR indicator begins
to flash. To initialize the HDD or to save images stored on it,
contact the dealer from whom this digital video recorder was
purchased.
7