Before Use; Notes On Handling Internal Hard Disk Drive Components; Do Not Use The Digital Video Recorder In The Following Locations; The Hard Disk And Cooling Fan Are Consumables - Sanyo DSR-M810PA Instruction Manual

1

BEFORE USE

Notes on handling internal hard disk
drive components
This unit has a built-in hard disk drive (HDD).
Be sure to observe the following points carefully when
operating, setting-up and servicing the unit.
Do not subject the unit to shocks or vibration.
If the unit is subjected to shocks or vibration, it may damage
the HDD or cause corruption of the data stored in the HDD.
Do not move the unit while the power is turned on. Turn
off the power and wait approximately 30 seconds before
removing the unit from or placing it in a rack.
When transporting the unit, pack it securely using the
specified packing materials. In addition, use a method
of transportation that minimizes vibration.
When placing the unit down on a surface such as a
floor, attach the specified feet to the base of the unit
and place it down gently.
Do not move the unit for 30 seconds after
turning off the power.
After the power is turned off, the disk inside the HDD will
continue to spin for a brief period due to inertia, and the
heads will be in an unstable state.
During this time, the unit is even more susceptible to
shocks and vibration than when power is being supplied.
Make sure that the unit is not subjected to even gentle
vibration for at least 30 seconds after turning off the power.
Do not operate the unit when condensation has
formed.
If the unit is operated when condensation has formed, it
may cause operating problems.
If sudden changes in the ambient temperature occur, wait
for the temperature to stablize before operating the unit.
Notes when replacing the HDD
Be sure to follow the correct replacement procedure when
replacing the HDD.
HDDs that have been removed from their packing may
not operate correctly if they are subjected to any shocks
and vibration. It is recommended that you place HDD
onto a soft, level surface with the printed circuit board
facing upward after unpacking it.
Be careful not to subject the HDD to shocks or vibration
when removing and tightening screws as part of the
HDD replacement procedure.
Make sure that all screws are tightened securely so that
they will not become loose.
The HDD is sensitive to static electricity, so you should
take proper precautions to prevent static electricity
buildup.
English
Handling the HDD unit by itself
If transporting or storing the HDD unit by itself, always be
sure to pack it in the specified packing first.
In addition, use a method of transportation that minimizes
the vibration.
If the HDD becomes damaged, handle the unit and the
damaged HDD that has been removed in order for it to be
replaced carefully to prevent the problem from being
aggravated until as the nature of the problem can be
checked and analyzed.
Do not use the digital video recorder in
the following locations:
The hard disk is sensitive to dust, vibrations and
shocks, and should also not be used near magnetic
objects. To prevent loss of recorded data, observe the
following precautions:
Do not subject the digital video recorder to shocks.
Do not use the digital video recorder on a vibrating or
unstable surface.
Do not disconnect the power plug from the wall outlet
during recording or playback.
Do not use the digital video recorder in areas of
extreme temperature changes (10ºC or more per hour).
Condensation may occur if the digital video recorder is
moved to an area of extremely different temperature or
high humidity. If the digital video recorder is used with
condensation inside it, operating problems may occur.
Do not install the digital video recorder in areas of
constant vibration such as motor vehicles or trains.
The hard disk and cooling fan are
consumables.
Under use in an ambient temperature of 25ºC, the hard disk
should generally be replaced after 2 years, and the cooling
fan after 3 years. These figures are intended as guidelines
only, and are not guarantees of part performance.
The POWER indicator flashes if a problem occurs in the
hard disk or fan. ( P.10)

Installation conditions

The digital video recorder has ventilation holes on its left,
rear and bottom panels. Make sure these holes are not
blocked after installation.
Do not use the unit in an area of poor ventilation such as a
bookshelf or box.
When installing the unit in a rack, ensure a gap of at least 5
cm at the top and bottom.
5