I Programmed Scan Operation; I Memory Scan Operation; I Select Memory Scan Operation; I Priority Watch - Icom I706MKTMG Instruction Manual

I Programmed scan operation

➀
Select VFO mode.
➁
Select the desired operating mode.
• The operating mode can also be changed while scan-
ning.
➂
Set [SQL] open or closed.
• See page a left for squelch condition.
➃
Select S2, then push [
• Decimal point blinks while scanning.
➄
When the scan detects a signal, the scan turns
OFF, pauses or ignores it depending on the
resume setting and the squelch condition.
• During scan [TS] can be used only when resume is ON.
➅
To cancel the scan push [

I Memory scan operation

➀
Select memory mode.
➁
Close the squelch with [SQL].
➂
Select S2, then push [
• Decimal point blinks while scanning.
➃
When the scan detects a signal, the scan stops or
pauses depending on the resume setting.
➄
To cancel the scan push [

I Select memory scan operation

➀
Select memory mode.
➁
Close the squelch with [SQL].
➂
Select S2, then push [
ory scan.
• Decimal point blinks while scanning.
➃
SEL] to change the memory scan to
Push [
(F-2)
select memory scan.
• Push [ SEL] for 2 sec. to clear all select memory
(F-2)
channels.
➄
When the scan detects a signal, the scan stops or
pauses depending on the resume setting.
➅
To cancel the scan push [

I Priority watch

➀
Select VFO mode, then set a frequency.
➁
Close the squelch with [SQL].
➂
Set the desired memory channel as the watching
channel.
➃
Select S2, then push [
• Decimal point blinks while scanning.
➄
When the scan detects a signal, the scan pauses
for 10 sec. or until the signal disappears, depend-
ing on the resume setting.
➅
To cancel the scan push [
SCN] to start the scan.
(F-1)
SCN].
(F-1)
SCN] to start the scan.
(F-1)
SCN].
(F-1)
SCN] to start the mem-
(F-1)
SCN].
(F-1)
PRI] to start the watch.
(F-2)
PRI].
(F-2)
MEMORY AND SCAN OPERATION
USB
VFO A
S1 3 5 7 9 20 40 60dB
P 5 10
O
S2 SCN PRI V/M
F-1
then push [
(F-1)
Note: If the same frequencies are programmed into
the scan edge memory channels 1A and 1B, pro-
grammed scan does not start.
USB
S1 3 5 7 9 20 40 60dB
MEMO
P 5 10
O
S2 SCN SEL V/M
F-1
then push [
(F-1)
Note: Two or more memory channels must be pro-
grammed for memory scan to start.
USB
S1 3 5 7 9 20 40 60dB
MEMO
P 5 10
O
S2 SCN SEL V/M
F-1 F-2
SCN], then [
Push [
(F-1)
Note: Two or more memory channels must be desig-
nated as select memory channels for select memory
scan to start.
USB
VFO A
S1 3 5 7 9 20 40 60dB
P 5 10
O
S2 SCN PRI V/M
F-2
Push [
Note: The paused condition when detecting a signal
differs depending on the scan resume condition.
resume on: pauses for 10 sec.
resume off: pauses until the signal disappears.
Select
VFO mode
CH
SCN]
Select
memory mode
CH
SCN]
Select
memory mode
Designate
S
CH
"S."
SEL].
(F-2)
Select
VFO mode
Select watching
CH
channel
PRI].
(F-2)
5
44