Loewe Connect ID 46 Operating Instructions Manual page 24

Connect ID 32-46
Operating instructions
Initial installation
Setting options for DVB-C reception:
If you have not selected a DVB-C antenna in the antenna selection: Con-
tinue with Setting options for DVB-S reception (see right hand column).
Network If several networks are available over DVB-C, you can
selection decide which network you want to receive your channels
from. The normal DVB-C settings are derived from the
selection of the location or network and do not need
to be changed. Exactly which of the following settings
are present is dependent on which network is selected.
Select network,
OK Proceed.
Settings
INITIAL INSTALLATION (DVB-C)
Scrambled stations
Search method
Start frequency
Network ID
Symbol rate 1 (DVB-C)
Symbol rate 2 (DVB-C)
QAM modulation 1
QAM modulation 2
Proceed
OK
Select and adapt settings for DVB-C reception.
Encrypted You can state whether coded stations are to be searched
stations for in the search/update.
scrambled stations. However, these stations can only be
received in connection with a CA module and the
appropriate Smart Card.
described on page 63.
If a CA module with a SmartCard is already plugged in
for the station search, all the stations which this module
can descramble are also saved when no is preset.
Search If you want to run the station search independently of
method the channel grid, select frequency search for the search
method.
Start The DVB stations are only searched for in the frequency
frequency range above the start frequency.
Network ID Only change these defaults if you are familiar with other
symbol rates and types of modulation or if you have to
Symbol rate specify the network ID for your cable network. In the
case of small cable networks fed directly from the satel-
QAM lite, the rate of 6900 might have to be replaced by 6111.
modulation Your cable provider has the information you need.
OK Proceed.
- 24 -
no yes
Channel search
047.0 MHz
none
6875
6900
64
256
Select yes to save all found
Handling of the CA module is
Setting options for DVB-S reception:
If you have not selected a DVB-S antenna in the antenna selection:
Continue with Setting options for all types of reception on page 28.
The normal DVB-S settings are derived from the selection
of the location and do not need to be changed in most
cases.
Select
INITIAL INSTALLATION (DVB-S)
satellite
Select satellite installation
installation Single satellite
2 satellites on 22 kHz switchbox
2 satellites on toneburst switch
Max. 4 satellites on DiSEqC multiswitch
DiSEqC one cable communal system
other communal installation
Proceed
OK
Selecting the satellite system.
Specify how you receive which satellite(s) (single
satellite or type of satellite system). Ask your
dealer if required.
Single Reception of a single satellite via a connected LNC (LNB).
satellite See page 25 for settings.
Reception of two different satellites with two LNCs
2 satellites
(LNBs) which are connected to the TV set by a 22 kHz
on 22 kHz
switchbox switchbox. See page 25 for settings.
2 satellites Reception of two different satellites with two LNCs
(LNBs) which are connected to the TV set by a toneburst
on toneburst
switch. See page 25 for settings.
switch
Max. 4 The TV set controls a DiSEqC multiswitch to which up
satellites to four LNCs (LNBs) for different satellites are connect-
ed. See page 26 for settings.
on DiSEqC
multiswitch
DiSEqC Select setting if the TV set is connected to a DiSEqC
one cable single-cable system (according to EN 50494). Several
communal Sat receivers can be connected to one Sat cable. See
page 26 for settings.
system
other Select setting if the TV set is connected to a single-cable
communal system (without DiSEqC). Several Sat receivers can be
installation connected to one Sat cable. Unlike a DiSEqC single-cable
system there are restrictions in the range of certain
reception frequencies in single-cable community
systems. See page 27 for settings.
OK Proceed
(to the appropriate page of the satellite system).
OK
Back